How to remove the front Sway Bar Kit on Toyota Sequoia?

The first step in unstabilizing the front bar involves removing the front wheel from its mounting point. The front sway bar kit assembly on the left-hand side needs its bolt and nut and sway bar link removed as well as a 6 mm hexagon wrench to hold the stud when the ball joint rotates with the nut. You must perform this process once again on the right-hand side of the vehicle. The procedure starts with front sway bar bracket removal through bolting out four pieces and detaching two brackets. Extract the front sway bar kit from the vehicle following which remove its 2 brackets together with cushions. The last step involves taking off both bushes present on the front sway bar kit to complete the removal process.

How to install the rear Sway Bar Kit on Toyota Sequoia?

Begin rear sway bar kit installation by inserting the 2 bushes through their cutouts toward the back of the vehicle. These bushes must fit onto the outer bush stopper position of the rear sway bar kit. The 4 sway bar kit bolts should be used to temporarily secure the rear sway bar kit then tighten the rear sway bar bracket to 27 Nm (275 kgf-cm, 20 ft-lbf). Attach two nuts to the provisional installation of rear sway bar link assembly on the left side while performing the same steps for the right side. The installation of the propeller shaft assembly starts with 2WD vehicles but includes steps for installing the propeller shaft assembly for 4WD vehicles which also involves transferring heat insulator and removing propeller shaft heat insulator. Apply the exhaust pipe assembly tail according to the requirements of both the 3UR-FE and the 2UZ-FE engine types. Secure the suspension before using a torque wrench to fasten the left side of the rear sway bar link assembly to 98 Nm (999 kgf-cm, 72 ft-lbf). Then tighten the right side.

OEM Toyota Sequoia Sway Bar Kit

Stabilizer Sway Bar Set

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

10 Sway Bar Kits found

View related parts
Toyota Sequoia Stabilizer Bar, Front
Part Number: 48811-AF021
$134.64 MSRP: $190.61
You Save: $55.97 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bar, Stabilizer, Front; Suspension Stabilizer Bar, Front; Sway Bar
- Manufacturer Note: OFF ROAD PACKAGE
- Position: Front
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2001-2004 Toyota Sequoia | Limited, SR5 | 8 Cyl 4.7 L GAS
View related parts
Toyota Sequoia Stabilizer Bar, Rear
Part Number: 48812-AF020
$135.82 MSRP: $192.27
You Save: $56.45 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bar, Stabilizer, Rear; Suspension Stabilizer Bar, Rear; Sway Bar
- Position: Rear
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2001-2007 Toyota Sequoia | Limited, SR5 | 8 Cyl 4.7 L GAS
View related parts
Toyota Sequoia Stabilizer Bar, Rear
Part Number: 48812-AF010
$119.02 MSRP: $168.49
You Save: $49.47 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bar, Stabilizer, Rear; Suspension Stabilizer Bar, Rear; Sway Bar
- Manufacturer Note: W(SUN ROOF)
- Position: Rear
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2001-2007 Toyota Sequoia | Limited, SR5 | 8 Cyl 4.7 L GAS
View related parts
Toyota Sequoia Stabilizer Bar, Rear
Part Number: 48812-0C040
$98.94 MSRP: $138.88
You Save: $39.94 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bar, Stabilizer, Rear
- Position: Rear
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2023-2024 Toyota Sequoia | Capstone, Limited, Platinum, SR5, TRD Pro | 6 Cyl 3.4 L FULL HYBRID EV-GAS (FHEV)
View related parts
Toyota Sequoia Stabilizer Bar, Rear
Part Number: 48812-0C020
$92.66 MSRP: $130.05
You Save: $37.39 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bar, Stabilizer, Rear; Suspension Stabilizer Bar, Rear; Sway Bar
- Manufacturer Note: TRD SPORT PACKAGE
- Position: Rear
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2008-2022 Toyota Sequoia | Limited, Nightshade, Platinum, SR5, TRD Pro, TRD Sport | 8 Cyl 4.6 L GAS, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L FLEX, 8 Cyl 5.7 L GAS
View related parts
Toyota Sequoia Stabilizer Bar, Front
Part Number: 48811-AF040
$154.03 MSRP: $218.05
You Save: $64.02 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bar, Stabilizer; Suspension Stabilizer Bar, Front; Sway Bar; Bar, Stabilizer, Front
- Manufacturer Note: W(AIR SUSPENSION)
- Position: Front
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2005-2007 Toyota Sequoia | Limited, SR5 | 8 Cyl 4.7 L GAS
View related parts
Toyota Sequoia Stabilizer Bar, Front
Part Number: 48811-AF030
$159.67 MSRP: $226.04
You Save: $66.37 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bar, Stabilizer; Suspension Stabilizer Bar, Front; Sway Bar; Bar, Stabilizer, Front
- Manufacturer Note: W(REAR STABILIZER)
- Position: Front
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2001-2007 Toyota Sequoia | Limited, SR5 | 8 Cyl 4.7 L GAS
View related parts
Toyota Sequoia Stabilizer Bar, Front
Part Number: 48811-0C030
$147.10 MSRP: $208.24
You Save: $61.14 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bar, Stabilizer, Front; Suspension Stabilizer Bar, Front; Sway Bar
- Manufacturer Note: TRD SPORT PACKAGE
- Position: Front
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2008-2022 Toyota Sequoia | Limited, Nightshade, Platinum, SR5, TRD Pro, TRD Sport | 8 Cyl 4.6 L GAS, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L FLEX, 8 Cyl 5.7 L GAS
View related parts
Toyota Sequoia Stabilizer Bar, Front
Part Number: 48804-0C020
$308.95 MSRP: $441.11
You Save: $132.16 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bar Sub-Assembly, Front Stabilizer; Suspension Stabilizer Bar, Front; Bar, Stabilizer, Front
- Manufacturer Note: TRD PRO PACKAGE
- Position: Front
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2023-2024 Toyota Sequoia | TRD Pro | 6 Cyl 3.4 L FULL HYBRID EV-GAS (FHEV)
View related parts
Toyota Sequoia Stabilizer Bar, Front
Part Number: 48804-0C010
$228.44 MSRP: $326.16
You Save: $97.72 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bar Sub-Assembly, Front Stabilizer; Suspension Stabilizer Bar, Front; Bar, Stabilizer, Front
- Manufacturer Note: 3" LIFT KIT PACKAGE
- Position: Front
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2023-2024 Toyota Sequoia | Capstone, Limited, Platinum, SR5, TRD Pro | 6 Cyl 3.4 L FULL HYBRID EV-GAS (FHEV)

Toyota Sequoia Sway Bar Kit

Choose genuine Sway Bar Kit that pass strict quality control tests. You can trust the top quality and lasting durability. Shopping for OEM Sway Bar Kit for your Toyota Sequoia? Our website is your one-stop destination. We stock an extensive selection of genuine Toyota Sequoia parts. The price is affordable so you can save more. It only takes minutes to browse and find the exact fit. Easily add to cart and check out fast. Our hassle-free return policy will keep you stress-free. We process orders quickly for swift delivery. Your parts will arrive faster, so you can get back on the road sooner.

The Sway Bar Kit in Toyota Sequoia vehicles aim at improving the performance of the car especially in area of cornering and where the car is in contact with the road irregularities. This kit joins contrary sections of suspension and uses anti-roll bar boosting roll stiffness while neither affecting vertical spring rate. In this manner, the Sway Bar Kit is able to prevent torsion, and this way, the heights of the wheels are alike, diminishing sideways tilt and improving grip on the asphalt. In the course of the Toyota Sequoia, there has been several designs of the Sway Bar Kits with the use of the adjustable and Active Anti-roll bar. Such systems can adapt a car's stiffness and stability in response to how it is being driven and road conditions. Where conventional sway bars transfer the bumps from one wheel to the other, new generations seek to refine the ride comfort, and minimize others sensations not wanted for a well balanced vehicle feel in the Toyota Sequoia.

Toyota Sequoia Sway Bar Kit Parts and Q&A

Stabilizer Bar, Front
48811-0C030
Q: How to remove the front Sway Bar Kit on Toyota Sequoia?
A:
The first step in unstabilizing the front bar involves removing the front wheel from its mounting point. The front sway bar kit assembly on the left-hand side needs its bolt and nut and sway bar link removed as well as a 6 mm hexagon wrench to hold the stud when the Ball Joint rotates with the nut. You must perform this process once again on the right-hand side of the vehicle. The procedure starts with front sway bar bracket removal through bolting out four pieces and detaching two brackets. Extract the front sway bar kit from the vehicle following which remove its 2 brackets together with cushions. The last step involves taking off both bushes present on the front sway bar kit to complete the removal process.
Stabilizer Bar, Rear
48812-0C020
Q: How to install the rear Sway Bar Kit on Toyota Sequoia?
A:
Begin rear sway bar kit installation by inserting the 2 bushes through their cutouts toward the back of the vehicle. These bushes must fit onto the outer bush stopper position of the rear sway bar kit. The 4 sway bar kit bolts should be used to temporarily secure the rear sway bar kit then tighten the rear sway bar bracket to 27 Nm (275 kgf-cm, 20 ft-lbf). Attach two nuts to the provisional installation of rear sway bar link assembly on the left side while performing the same steps for the right side. The installation of the propeller shaft assembly starts with 2WD vehicles but includes steps for installing the propeller shaft assembly for 4WD vehicles which also involves transferring heat insulator and removing propeller shaft heat insulator. Apply the Exhaust Pipe assembly tail according to the requirements of both the 3UR-FE and the 2UZ-FE engine types. Secure the suspension before using a torque wrench to fasten the left side of the rear sway bar link assembly to 98 Nm (999 kgf-cm, 72 ft-lbf). Then tighten the right side.

Related Toyota Sequoia Parts

Browse Toyota Sequoia Sway Bar Kit by Years

2024 2023 2022 2021 2020 2019 2018 2017 2016 2015 2014 2013 2012 2011 2010 2009 2008 2007 2006 2005 2004 2003 2002 2001