Other Name: Knob & Element Assembly; Cigarette Lighter Element; Element; Lighter; Knob; Knob And Element Assembly, Cigarette Lighter
Replaces: 85520-30210
Fits the following Toyota Models:
Avalon | 1995-1998 | XL, XLS | 6 Cyl 3.0 L GAS
Highlander | 2001-2007 | Base, Hybrid, Hybrid Limited, Limited, Sport | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.3 L GAS
Land Cruiser | 1998-2007 | Base | 8 Cyl 4.7 L GAS
Supra | 1993-1996 | Base, Twin Turbo | 6 Cyl 3.0 L GAS
4Runner | 1996-1998 | Base, Limited, SR5 | 4 Cyl 2.7 L GAS, 6 Cyl 3.4 L GAS
Corolla | 2005-2008, 1993-1997 | Base, CE, DX, LE, S | 4 Cyl 1.6 L GAS, 4 Cyl 1.8 L GAS
Highlander | 2001-2007 | Base, Hybrid, Hybrid Limited, Limited, Sport | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.3 L GAS
Land Cruiser | 1998-2007 | Base | 8 Cyl 4.7 L GAS
MR2 Spyder | 2000-2005 | Base | 4 Cyl 1.8 L GAS
RAV4 | 2004-2005 | Base, L, Sport | 4 Cyl 2.4 L GAS
Sequoia | 2001-2004 | Limited, SR5 | 8 Cyl 4.7 L GAS
Sienna | 1998-2003 | CE, LE, XLE | 6 Cyl 3.0 L GAS
Supra | 1993-1996 | Base, Twin Turbo | 6 Cyl 3.0 L GAS
Tacoma | 1995-2004 | Base, DLX, Limited, Pre Runner, SR5, S-Runner | 4 Cyl 2.4 L GAS, 4 Cyl 2.7 L GAS, 6 Cyl 3.4 L GAS
Q: How to install a Cigarette Lighter and its related components on Toyota 4Runner?
A: Applying the Cigarette Lighter socket assembly requires users to position it correctly with the notch on the Cigarette Lighter socket cover then force it into place. Begin by placing the rear deck trim cover after setting up the tonneau cover hook. The installation should proceed with the deck floor box RH followed by the deck board assembly and the deck board sub-assembly. You should start by adding the rear floor mat support plate rear followed by the back door Weather Strip then finish with installation of the tonneau cover retractor sub-assembly. Finish the installation by adding the rear door opening trim Weather Strip on the right-hand side and the rear door scuff plate RH.
Q: How to Service the Cigarette Lighter Assembly on Toyota Camry?
A: Service of the Auxiliary Power Outlet starts with removing three components: SHIFT LEVER KNOB SUB-ASSEMBLY (M/T TRANSAXLE), CONSOLE PANEL UPPER REAR and CONSOLE BOX CARPET and RR CONSOLE BOX. The CIGARETTE LIGHTER ASSEMBLY RR needs to be removed by disassembling the clamp before rotating the socket along its circumference to release the claw between the socket and power outlet socket cover RR. This will allow the socket to extend toward the room area. The installation procedure requires placing the CIGARETTE LIGHTER ASSEMBLY RR into the notched area of the power outlet socket cover RR before forcing it deep into position and tightening it into place.
Q: How to Replace a Cigarette Lighter Assembly on Toyota Tacoma?
A: Begin the Cigarette Lighter Assembly replacement procedure by disconnecting the negative battery terminal cable. A torx(R) socket wrench (T30) enables removal of the 4 screws securing the assembly after which workers detach the connector before they remove the clamp and cigarette lighter assembly. Beginning installation requires first connecting the connector to the clamp followed by screw installation using the torx(R) socket wrench (T30) according to a specified order and a torque requirement of 5.0 N.m (51 kgf.cm, 44 in.lbf). Finish up by attaching the cable to the negative battery terminal while torquing it to 3.9 N.m (40 kgf.cm, 35 in.lbf).