How to remove the front and rear bumper cover on 2007 through 2015 Toyota Avalon?

First, push the front of the fender-well liner back, place the parking brake, lift the car, and use jackstands to stabilize it. Loosen the battery cable and, if you have fog lights, disconnect the wires at the back of the bumper cover where they plug into the lights. You can slide the grille loose by removing bolts and a retaining clip, then pulling it away carefully while detaching all the mounting clips from their places. Unclip three screws that mount the radiator support cover, and also lower the cover. Disconnect the bumper cover using screws and pushpins. Push the plastic fastener button center-up using a tiny screwdriver blade, but leave the center buttons attached. Unscrew and take out all anchors before starting to take the cover off. Push and turn the two front locking pins 90 degrees, then pull the fender well liner back and undo the bumper cover-to-fender mounting bolt. Use both hands to unbolt the four clips holding the cover on its frontmost attachment points with the fenders. You'll need help to put the new bumper cover on, as you slide the tabs back into body clips, tighten bolts and screws, beginning from the backside. To remove the bumper cover from the back of the car, first detach the plastic pins near the bottom of the cover while working underneath the vehicle, then undo the appropriate screw(s) along the front edge. Also loosen any plastic fenderwell liner, if necessary. Take off the trunk lid. Unplug and take out the wiring for the parking sensors and camera, if they're on your car. Pry the screws out that keep the bumper cover in place on the bottom, and carefully pull back the cover while hitting any unplugged bolts with a plastic hammer from beneath the car. Installation is the reverse of removal.

How to remove and install the front and rear bumper cover on 2002 through 2008 Toyota Solara?

To work on Solara models, you should glide back part of the fenderwell liner, engage the parking brake, lift the vehicle, then place it on secure jackstands. Unplug the wiring from the battery's negative part. When your car has foglights built in, remove their electrical connections from the back of the bumper's lower cover. Unscrew or remove all pushpins and screws that keep the bumper cover in place, including those under the splash apron, along the bumper's bottom edge, and at each side. Push up the middle button on each plastic fastener using a tiny screwdriver so the fastener stays in place. Be sure all screw points are marked and eliminated before trying to disassemble the fascia, as this part may have different screw numbers and locations than other models. To remove the front cover of Solara models, undo three screws and the radiator grille, then take off the protective panel. Installation goes in the opposite direction, matching the bumper cover's tabs with the vehicle's clips before you bolt and screw them in, with a second person to assist you works best. Work under the car to disconnect plastic clips and screws keeping the lower edge of the bumper cover attached. In the rear fenders, remove any screws holding the front edge of the fascia to the fenderwell, freeing the plastic fender covering if needed. Open your trunk and pull up the mat. Unhook the bumper cover fasteners at each corner inside the trunk using a trim tool. Then take out the clips on the back wall behind the trunk trim panel. Use a small screwdriver to lift up the button on the plastic fasteners of the upper bumper cover clips while pulling the cover outward from the trunk. You don't need to remove the clips to do this. When you need to take out bolts or sticks from a car's body, hit them with a plastic hammer. Installation is the reverse of removal.

OEM Toyota Bumper Cover

Bumper Shell

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

608 Bumper Covers found

View related parts
Toyota Bumper Cover, Front Driver Side Part Number: 52119-0R919
$155.32 MSRP: $219.88
You Save: $64.56 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover, Front Bumper L/P; Bumper Cover, Front Upper; Cover, Front Bumper
- Position: Front Driver Side
- Replaces: 52119-4A916
Fits the following Toyota Models:
- RAV4 | 2019-2025 | Adventure, Hybrid LE, Hybrid Limited, Hybrid SE, Hybrid Woodland Edition, Hybrid XLE, Hybrid XLE Premium, Hybrid XSE, LE, Limited, Plug-In Hybrid SE, Plug-In Hybrid XSE, TRD Off-Road, XLE, XLE Premium | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 4 Cyl 2.5 L PLUG-IN HYBRID EV-GAS (PHEV)
- RAV4 Prime | 2021-2024 | SE, XSE | 4 Cyl 2.5 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Toyota Bumper Cover, Gray, Rear Part Number: 52159-0R160
$162.14 MSRP: $229.53
You Save: $67.39 (30%)
ADD TO CART
Product Specifications
- Other Name: Cover, Rear Bumper; Bumper Cover, Rear
- Manufacturer Note: NO PAINT REQ.
- Position: Rear
- Replaces: 52159-42220
Fits the following Toyota Models:
- RAV4 | 2019-2025 | Hybrid LE, Hybrid Limited, Hybrid SE, Hybrid Woodland Edition, Hybrid XLE, Hybrid XLE Premium, Hybrid XSE, LE, XLE, XLE Premium | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS
View related parts
Toyota Bumper Cover, Front Part Number: 52119-35071
$180.56 MSRP: $257.80
You Save: $77.24 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover, Front Bumper; Bumper Cover, Front
- Manufacturer Note: NO PAINT REQ.
- Position: Front
- Replaces: 52119-35070
Fits the following Toyota Models:
- FJ Cruiser | 2007-2014 | Base, Trail Teams Special Edition, TRD Special Edition | 6 Cyl 4.0 L GAS
View related parts
Toyota Bumper Cover, Front Part Number: 52119-04090
$200.37 MSRP: $286.08
You Save: $85.71 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover, Front Bumper; Bumper Cover, Front
- Position: Front
Fits the following Toyota Models:
- Tacoma | 2012-2015 | Base, Pre Runner, TRD Pro | 4 Cyl 2.7 L GAS, 6 Cyl 4.0 L GAS
View related parts
Toyota Bumper Cover, Front Part Number: 52119-06974
$239.51 MSRP: $341.97
You Save: $102.46 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover, Front Bumper, Le; Bumper Cover, Front; Cover, Front Bumper
- Manufacturer Note: PAINT REQ.
- Position: Front
Fits the following Toyota Models:
- Camry | 2012-2014 | Hybrid LE, Hybrid XLE, L, LE, XLE | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.5 L GAS
View related parts
Toyota Bumper Cover, Front Driver Side Part Number: 52119-F2922
$150.62 MSRP: $213.23
You Save: $62.61 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover, Front Bumper. L/; Bumper Cover, Front; Cover, Front Bumper
- Manufacturer Note: PAINT REQ.
- Position: Front Driver Side
Fits the following Toyota Models:
- Corolla | 2020-2025 | FX, Hybrid LE, Hybrid Nightshade, Hybrid SE, Hybrid XLE, L, LE, Nightshade, SE, SE Apex, SE Nightshade, XLE, XSE, XSE Apex | 4 Cyl 1.8 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS
View related parts
Toyota Bumper Cover, Front Driver Side Part Number: 52119-08905
$241.84 MSRP: $345.30
You Save: $103.46 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover, Front Bumper L/P; Bumper Cover, Front; Cover, Front Bumper
- Position: Front Driver Side
Fits the following Toyota Models:
- Sienna | 2018-2020 | L, LE, SE, SE Premium, XLE, XLE Premium | 6 Cyl 3.5 L GAS
View related parts
Toyota Bumper Cover, Front Driver Side Part Number: 52119-06958
$250.81 MSRP: $358.10
You Save: $107.29 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover, Front Bumper L/ P; Bumper Cover, Front; Cover, Front Bumper
- Manufacturer Note: PAINT REQ.
- Position: Front Driver Side
Fits the following Toyota Models:
- Camry | 2010-2011 | Base, LE, XLE | 4 Cyl 2.5 L GAS, 6 Cyl 3.5 L GAS
View related parts
Toyota End Cap, Passenger Side Part Number: 52155-0C903
$146.63 MSRP: $207.57
You Save: $60.94 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Insert, Rear Bumper Extension; Bumper Corner Cover, Rear Right Lower; Bar, Rear Bumper, Passenger Side
- Position: Passenger Side
Fits the following Toyota Models:
- Tundra | 2014-2021 | 1794 Edition, Limited, Nightshade, Platinum, SR, SR5, Trail, TRD Pro | 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.7 L FLEX, 8 Cyl 5.7 L GAS
View related parts
Toyota Bumper Cover, Front Driver Side Part Number: 52119-12994
$154.27 MSRP: $218.38
You Save: $64.11 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover, Front Bumper L/P; Bumper Cover, Front; Cover, Front Bumper
- Position: Front Driver Side
Fits the following Toyota Models:
- Corolla | 2019-2022 | SE, SE Nightshade, XSE | 4 Cyl 2.0 L GAS
View related parts
Toyota Bumper Cover, Front Driver Side Part Number: 52119-0X936
$191.28 MSRP: $273.11
You Save: $81.83 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover, Front Bumper L/C; Bumper Cover, Front; Cover, Front Bumper
- Position: Front Driver Side
- Replaces: 52119-3T930
Fits the following Toyota Models:
- Camry | 2018-2020 | Hybrid LE, Hybrid XLE, L, LE, XLE | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.5 L GAS
View related parts
Toyota Bumper Cover, Front Driver Side Part Number: 52119-35918
$215.51 MSRP: $307.70
You Save: $92.19 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover, Front Bumper L/P; Bumper Cover, Front; Cover, Front Bumper
- Manufacturer Note: PAINT REQ.
- Position: Front Driver Side
- Replaces: 52119-35915, 52119-35912
Fits the following Toyota Models:
- 4Runner | 2014-2024 | 40th Anniversary Edition, SR5, SR5 Premium, Trail, TRD Off-Road Premium | 6 Cyl 4.0 L GAS
View related parts
Toyota Bumper Cover, Front Driver Side Part Number: 52119-0X937
$191.28 MSRP: $273.11
You Save: $81.83 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover, Front Bumper L/C; Bumper Cover, Front; Cover, Front Bumper
- Position: Front Driver Side
Fits the following Toyota Models:
- Camry | 2018-2020 | Hybrid LE, Hybrid XLE, L, LE, XLE | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.5 L GAS
View related parts
Toyota Bumper Cover, Rear Part Number: 52150-0R110
$196.87 MSRP: $281.09
You Save: $84.22 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bumper Assembly, Rear; Bumper Cover, Rear; Cover, Rear Bumper
- Manufacturer Note: NO PAINT REQ.
- Position: Rear
- Replaces: 52159-0R070, 52150-42830
Fits the following Toyota Models:
- RAV4 | 2013-2015 | LE, Limited, XLE | 4 Cyl 2.5 L GAS
View related parts
Toyota Bumper Cover, Front Part Number: 52119-04060
$200.37 MSRP: $286.08
You Save: $85.71 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover, Front Bumper; Bumper Cover, Front
- Manufacturer Note: NO PAINT REQ.
- Position: Front
Fits the following Toyota Models:
- Tacoma | 2012-2015 | Base, Pre Runner, TRD Pro | 4 Cyl 2.7 L GAS, 6 Cyl 4.0 L GAS
View related parts
Toyota Bumper Cover, Front Part Number: 52119-04040
$222.04 MSRP: $317.02
You Save: $94.98 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover, Front Bumper; Bumper Cover, Front
- Position: Front
Fits the following Toyota Models:
- Tacoma | 2005-2011 | Base, Pre Runner, X-Runner | 4 Cyl 2.7 L GAS, 6 Cyl 4.0 L GAS
View related parts
Toyota Bumper Cover, Rear Driver Side Part Number: 52159-0X915
$248.83 MSRP: $355.28
You Save: $106.45 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover, Rear Bumper L/C; Bumper Cover, Rear; Cover, Rear Bumper
- Position: Rear Driver Side
- Replaces: 52159-33962
Fits the following Toyota Models:
- Camry | 2018-2024 | Hybrid SE, Hybrid SE Nightshade, Hybrid XSE, SE, SE Nightshade, XSE | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.5 L GAS
View related parts
Toyota Bumper Cover, Rear Part Number: 52159-35190
$284.02 MSRP: $405.51
You Save: $121.49 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover, Rear Bumper; Bumper Cover, Rear
- Manufacturer Note: NO PAINT REQ.
- Position: Rear
Fits the following Toyota Models:
- 4Runner | 2006-2009 | Limited, Sport, SR5 | 6 Cyl 4.0 L GAS, 8 Cyl 4.7 L GAS
View related parts
Toyota Bumper Cover, Front Part Number: 52119-02989
$243.59 MSRP: $347.79
You Save: $104.20 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover, Front Bumper; Bumper Cover, Front
- Position: Front
Fits the following Toyota Models:
- Corolla | 2009-2010 | Base, LE, S, XLE, XRS | 4 Cyl 1.8 L GAS, 4 Cyl 2.4 L GAS
View related parts
Toyota Upper Cover, Front Part Number: 52119-35911
$125.60 MSRP: $177.80
You Save: $52.20 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover, Front Bumper, Up; Valance Panel, Front
- Position: Front
- Replaces: 52119-35020
Fits the following Toyota Models:
- 4Runner | 1999-2002 | Base, Limited, SR5 | 4 Cyl 2.7 L GAS, 6 Cyl 3.4 L GAS

| Page 1 of 31 |Next >

1-20 of 608 Results

Toyota Bumper Cover

OEM parts deliver unmatched quality you can rely on. They pass extensive quality control inspections. Toyota produces them to the official factory specifications. This process helps prevent defects and imperfections. So you can get exceptional lifespan and a flawless fit. Need new OEM Toyota Bumper Cover? You'll love our wide selection of genuine options. Shop in minutes and skip the hunt. Our prices are unbeatable, you'll save time and money. It's easy to shop and find the right piece. Our committed customer service team gives professional help from start to finish. Every part includes a manufacturer's warranty. We ship quickly, your parts will arrive fast at your door.

Toyota Bumper Cover protects the bumper beneath from scrapes and gives the car a clean and aerodynamic appearance. It is a simple part with a big benefit. Founded in 1937 and revered by automobile manufacturers around the world, Toyota has developed a reputation for reliability, intelligently manufactured vehicles, and a constant focus on innovation. The company turns efficiency into perfection with its Hybrid Synergy Drive and its versatile TNGA platform, giving drivers hybrid options that not only save on fuel but reduce emissions and keep the journey going smoothly. Recent launches such as the RAV4 Plug-in Hybrid are indicative of how Toyota combines electric range and daily practicality. Owners favor vehicles that remain durable mile after mile as they provide responsive handling and dependable safety. That same dedication to well-thought design is contained in every Bumper Cover offered throughout the lineup. A Toyota Bumper Cover serves as the outer skin that conceals structural parts, directs cooling air, and produces a well-groomed look from the factory. Because it is shaped from lightweight plastic, the Bumper Cover is lightweight and absorbs small impacts while being resistant to corrosion and aiding in weight reduction in favor of overall efficiency. Openings for lights, sensors, and tow eye caps are integrated so a Toyota Bumper Cover could accommodate standard equipment or future upgrades without awkward gaps. Easy fitment to original mounting points allows owners to restore appearances and airflow in one step to maintain the vehicle's trusted balance of protection, performance, and good looks.

Toyota Bumper Cover Parts and Q&A

Bumper Cover, Front
52119-07904
Q: How to remove the front and rear bumper cover on 2007 through 2015 Toyota Avalon?
A:
First, push the front of the fender-well liner back, place the parking brake, lift the car, and use jackstands to stabilize it. Loosen the battery cable and, if you have fog lights, disconnect the wires at the back of the bumper cover where they plug into the lights. You can slide the grille loose by removing bolts and a retaining clip, then pulling it away carefully while detaching all the mounting clips from their places. Unclip three screws that mount the radiator support cover, and also lower the cover. Disconnect the bumper cover using screws and pushpins. Push the plastic fastener button center-up using a tiny screwdriver blade, but leave the center buttons attached. Unscrew and take out all anchors before starting to take the cover off. Push and turn the two front locking pins 90 degrees, then pull the fender well liner back and undo the bumper cover-to-fender mounting bolt. Use both hands to unbolt the four clips holding the cover on its frontmost attachment points with the fenders. You'll need help to put the new bumper cover on, as you slide the tabs back into body clips, tighten bolts and screws, beginning from the backside. To remove the bumper cover from the back of the car, first detach the plastic pins near the bottom of the cover while working underneath the vehicle, then undo the appropriate screw(s) along the front edge. Also loosen any plastic fenderwell liner, if necessary. Take off the trunk lid. Unplug and take out the wiring for the parking sensors and camera, if they're on your car. Pry the screws out that keep the bumper cover in place on the bottom, and carefully pull back the cover while hitting any unplugged bolts with a plastic hammer from beneath the car. Installation is the reverse of removal.
Bumper Cover, Rear Driver Side
52159-06945
Q: How to remove and install the front and rear bumper cover on 2002 through 2008 Toyota Solara?
A:
To work on Solara models, you should glide back part of the fenderwell liner, engage the parking brake, lift the vehicle, then place it on secure jackstands. Unplug the wiring from the battery's negative part. When your car has foglights built in, remove their electrical connections from the back of the bumper's lower cover. Unscrew or remove all pushpins and screws that keep the bumper cover in place, including those under the splash apron, along the bumper's bottom edge, and at each side. Push up the middle button on each plastic fastener using a tiny screwdriver so the fastener stays in place. Be sure all screw points are marked and eliminated before trying to disassemble the fascia, as this part may have different screw numbers and locations than other models. To remove the front cover of Solara models, undo three screws and the radiator grille, then take off the protective panel. Installation goes in the opposite direction, matching the bumper cover's tabs with the vehicle's clips before you bolt and screw them in, with a second person to assist you works best. Work under the car to disconnect plastic clips and screws keeping the lower edge of the bumper cover attached. In the rear fenders, remove any screws holding the front edge of the fascia to the fenderwell, freeing the plastic fender covering if needed. Open your trunk and pull up the mat. Unhook the bumper cover fasteners at each corner inside the trunk using a trim tool. Then take out the clips on the back wall behind the trunk trim panel. Use a small screwdriver to lift up the button on the plastic fasteners of the upper bumper cover clips while pulling the cover outward from the trunk. You don't need to remove the clips to do this. When you need to take out bolts or sticks from a car's body, hit them with a plastic hammer. Installation is the reverse of removal.