Other Name: Lock Assembly, Front Door W; Door Lock Actuator Motor, Front Left; Door Latch Assembly, Front Left; Lock Assembly; Front Door W/Motor, Driver Side; Door Lock Actuator Motor.
Position: Driver Side
Replaces: 69040-06180
Item Weight: 2.10 Pounds
Item Dimensions: 8.5 x 5.7 x 5.7 inches
Condition: New
Fitment Type: Direct Replacement
SKU: 69040-0C050
Warranty: This genuine part is guaranteed by Toyota's
factory warranty.
Other Name: Lock Assembly, Front Door W; Door Lock Actuator Motor, Front Right; Door Latch Assembly, Front Right; Lock Assembly; Front Door W/Motor, Passenger Side; Door Lock Actuator Motor; Door Latch Assembly.
Manufacturer Note: WIRELESS DOOR LOCK-WITH(PANIC BUTTON)&DOOR OUTSIDE HANDLE-BODY COLOR,W/O(PASSENGER KEY CYLINDER)&POWER WINDOW-WITH(DRIVER ONE TOUCH DOWN)
Position: Passenger Side
Item Weight: 1.50 Pounds
Item Dimensions: 8.0 x 5.6 x 5.7 inches
Condition: New
Fitment Type: Direct Replacement
SKU: 69030-42230
Warranty: This genuine part is guaranteed by Toyota's
factory warranty.
Other Name: Lock Assembly, Rear Door W; Actuator Motor, Rear Right; Latch Assembly, Center/Rear Right; Lock Assembly; Rear Door W/Motor, Passenger Side; Door Lock Actuator Motor.
Manufacturer Note: POWER WINDOW-WITH(DRIVER ONE TOUCH DOWN)
Position: Passenger Side
Replaces: 69050-42020
Item Weight: 1.60 Pounds
Item Dimensions: 9.1 x 6.0 x 3.6 inches
Condition: New
Fitment Type: Direct Replacement
SKU: 69050-42021
Warranty: This genuine part is guaranteed by Toyota's
factory warranty.
More Info
Fits the following 2009 Scion xD Submodels:
Base | 4 Cyl 1.8 L GAS
2009 Scion xD Door Lock
Looking for affordable OEM 2009 Scion xD Door Lock? Explore our comprehensive catalogue of genuine 2009 Scion xD Door Lock. All our parts are covered by the manufacturer's warranty. Plus, our straightforward return policy and speedy delivery service ensure an unparalleled shopping experience. We look forward to your visit!
2009 Scion xD Door Lock Parts Q&A
Q: How to install the front door lock on 2009 Scion xD?
A: First users must replace the connecting-part packing with new material and clean all packing surfaces free from dirt and grease before proceeding with the front door lock installation. Before installation, apply MP grease to all sliding and rotating components of the front door lock. The front door inside locking cable should be placed next followed by engagement of the 3 claws before closing the cover. The front door lock remote control cable should be installed alongside a new wire harness seal before going on the front door lock. Place the front door open rod into the front door lock while positioning it correctly against the outside handle frame before fully connecting it. Install the front door lock by using a 'TORX' socket wrench T30 to tighten three screws that received Toyota Genuine Adhesive 1324 or Three Bond 1324 or an equivalent while applying 5.0 Nm (51 kgf-cm, 44 in-lbf) force on the screws. After connecting the front door outside handle cover and front door frame rear lower sub-assembly the order of installation continues with front door window regulator sub-assembly, front door glass run, front door glass sub-assembly, front door service hole cover, front door trim bracket, front door belt moulding assembly, outer rear view mirror assembly, front door trim board sub-assembly, front door inside handle bezel, front door lower frame bracket garnish, and front armrest base upper panel. The installation process ends with connecting the cable to the negative battery terminal while tightening it at 5.4 Nm (55 kgf-cm, 48 in-lbf).