Other Name: Lock Assembly, Front Door W; Door Lock Actuator Motor, Front Left; Door Latch Assembly, Front Left; Lock Assembly; Front Door W/Motor, Driver Side; Door Lock Actuator Motor.
Position: Driver Side
Replaces: 69040-06180
Item Weight: 2.10 Pounds
Item Dimensions: 8.5 x 5.7 x 5.7 inches
Condition: New
Fitment Type: Direct Replacement
SKU: 69040-0C050
Warranty: This genuine part is guaranteed by Toyota's
factory warranty.
Other Name: Lock Assembly, Front Door W; Door Lock Actuator Motor, Front Right; Door Latch Assembly, Front Right; Lock Assembly; Front Door W/Motor, Passenger Side; Door Lock Actuator Motor; Door Latch Assembly.
Manufacturer Note: WIRELESS DOOR LOCK-WITH(PANIC BUTTON)&DOOR OUTSIDE HANDLE-BODY COLOR,W/O(PASSENGER KEY CYLINDER)&POWER WINDOW-WITH(DRIVER ONE TOUCH DOWN)
Position: Passenger Side
Item Weight: 1.50 Pounds
Item Dimensions: 8.0 x 5.6 x 5.7 inches
Condition: New
Fitment Type: Direct Replacement
SKU: 69030-42230
Warranty: This genuine part is guaranteed by Toyota's
factory warranty.
Other Name: Lock Assembly, Rear Door W; Actuator Motor, Rear Right; Latch Assembly, Center/Rear Right; Lock Assembly; Rear Door W/Motor, Passenger Side; Door Lock Actuator Motor.
Manufacturer Note: POWER WINDOW-WITH(DRIVER ONE TOUCH DOWN)
Position: Passenger Side
Replaces: 69050-42020
Item Weight: 1.60 Pounds
Item Dimensions: 9.1 x 6.0 x 3.6 inches
Condition: New
Fitment Type: Direct Replacement
SKU: 69050-42021
Warranty: This genuine part is guaranteed by Toyota's
factory warranty.
More Info
Fits the following 2008 Scion xD Submodels:
Base | 4 Cyl 1.8 L GAS
2008 Scion xD Door Lock
Looking for affordable OEM 2008 Scion xD Door Lock? Explore our comprehensive catalogue of genuine 2008 Scion xD Door Lock. All our parts are covered by the manufacturer's warranty. Plus, our straightforward return policy and speedy delivery service ensure an unparalleled shopping experience. We look forward to your visit!
2008 Scion xD Parts Questions & Experts Answers
Q: How to install the rear door lock on 2008 Scion xD?
A: The installation of the rear door lock starts by replacing the old door lock connecting part packing with new material while confirming the packing surface remains free of dirt and oil residue. Use MP grease to treat the sliding and rotating sections of the front door lock after which you can install the rear door inside locking cable while putting the 3 claws into position and sealing the cover. Place the rear door lock remote control cable then activate the claw mechanism before finishing with the closure of the cover. First install new door lock wire harness seals at the rear door lock area before you place the rear door lock onto the outside handle release plate and position it toward the rear door panel for outside handle lock engagement. The threads of the screws need Toyota Genuine Adhesive 1324 or Three Bond 1324 or equivalent before attaching them with a "TORX" socket wrench T30. Follow by tightening the 3 screws to 5.0 Nm (51 kgf-cm, 44 in-lbf) torque specification. Finally, complete the installation by connecting the connector. The installation process includes fitting the rear door window regulator sub-assembly together with the rear door glass sub-assembly followed by the rear door quarter window Weather Strip then the rear door window division bar sub-assembly then the rear door glass run followed by the rear door belt moulding assembly before installing the rear door Weather Strip after which comes the rear door service hole cover then the rear door trim bracket followed by the rear door trim board sub-assembly then the rear door inside handle bezel with the rear door armrest base upper panel finishing the process. Apply the cable to the negative battery terminal while torquing it to 5.4 Nm (55 kgf-cm, 48 in-lbf).