Other Name: Lock Assembly, Front Door W; Door Lock Actuator Motor, Front Left; Door Latch Assembly, Front Left; Lock Assembly; Front Door W/Motor, Driver Side; Door Lock Actuator Motor.
Position: Driver Side
Replaces: 69040-06180
Item Weight: 2.10 Pounds
Item Dimensions: 8.5 x 5.7 x 5.7 inches
Condition: New
Fitment Type: Direct Replacement
SKU: 69040-0C050
Warranty: This genuine part is guaranteed by Toyota's
factory warranty.
Other Name: Lock Assembly, Front Door W; Door Lock Actuator Motor, Front Right; Door Latch Assembly, Front Right; Lock Assembly; Front Door W/Motor, Passenger Side; Door Lock Actuator Motor; Door Latch Assembly.
Manufacturer Note: WIRELESS DOOR LOCK-WITH(PANIC BUTTON)&DOOR OUTSIDE HANDLE-BODY COLOR,W/O(PASSENGER KEY CYLINDER)&POWER WINDOW-WITH(DRIVER ONE TOUCH DOWN)
Position: Passenger Side
Item Weight: 1.50 Pounds
Item Dimensions: 8.0 x 5.6 x 5.7 inches
Condition: New
Fitment Type: Direct Replacement
SKU: 69030-42230
Warranty: This genuine part is guaranteed by Toyota's
factory warranty.
Other Name: Lock Assembly, Rear Door W; Actuator Motor, Rear Right; Latch Assembly, Center/Rear Right; Lock Assembly; Rear Door W/Motor, Passenger Side; Door Lock Actuator Motor.
Manufacturer Note: POWER WINDOW-WITH(DRIVER ONE TOUCH DOWN)
Position: Passenger Side
Replaces: 69050-42020
Item Weight: 1.60 Pounds
Item Dimensions: 9.1 x 6.0 x 3.6 inches
Condition: New
Fitment Type: Direct Replacement
SKU: 69050-42021
Warranty: This genuine part is guaranteed by Toyota's
factory warranty.
More Info
Fits the following 2010 Scion xD Submodels:
Base | 4 Cyl 1.8 L GAS
2010 Scion xD Door Lock
Looking for affordable OEM 2010 Scion xD Door Lock? Explore our comprehensive catalogue of genuine 2010 Scion xD Door Lock. All our parts are covered by the manufacturer's warranty. Plus, our straightforward return policy and speedy delivery service ensure an unparalleled shopping experience. We look forward to your visit!
2010 Scion xD Parts Questions & Experts Answers
Q: How to install the rear door lock on 2010 Scion xD?
A: Before installing the rear door lock check that you either use a new packing material for the connector or replace the old packing and be certain that the packing surface remains residue-free. Apply MP grease to all sliding and rotating points of the front door lock before installing the internal locking cable of the rear door. Properly fit the 3 claws then seal the opening with the cover. The rear door lock remote control cable installation requires the user to first position the claw before closing the cover. New door lock wire harness seal must be attached to the rear door lock before inserting the lock into the back door outside handle release plate while adjusting the lock position until the rear door outside handle properly locks into place. Use Toyota Genuine Adhesive 1324, Three Bond 1324 or similar adhesive to torque three screws of the rear door lock installation with a "TORX" socket wrench T30 until they reach 5.0 Nm (51 kgf-cm, 44 in-lbf). After connecting the connector it is necessary to install the listed components including rear door window regulator sub-assembly followed by rear door glass sub-assembly then rear door quarter window Weather Strip then rear door window division bar sub-assembly then rear door glass run then rear door belt moulding assembly then rear door Weather Strip then rear door service hole cover then rear door trim bracket then rear door trim board sub-assembly then rear door inside handle bezel and finally rear door armrest base upper panel. Secure the cable to the negative battery terminal while tightening it to 5.4 Nm (55 kgf-cm, 48 in-lbf).