How to service and repair a Hood Cable on Toyota Camry?

The initial step for servicing the hood cable involves wheel removal followed by taking out the 3 extension pad screws from the front wheel opening. The 2GR-FE engine cool air intake duct seal must be removed before proceeding with the front bumper assembly disassembly process that requires separate instructions depending on fog light equipment. Next, remove the front fender liner through the combination of 5 clips and a bolt and 4 screws and a grommet. You need to eliminate the horn assembly with high-pitched sounds. The assembly of the hood lock without the engine hood courtesy switch needs a set of three bolts removal and hood lock control cable disconnection before extracting the assembly from its position. To detach the assembly including an engine hood courtesy switch personnel should first disconnect the connector afterward remove 3 bolts then disconnect the hood lock control cable before proceeding with removal of the assembly. The technician must first detach the hood lock control cable before taking out the hood lock control lever sub-assembly. After disconnecting the assembly clamps with a screwdriver, tape the screwdriver tip first before pulling the cable from the engine compartment.

How to install the Hood Cable Assembly on Toyota Tundra?

Pass the cable into the engine room and facilitate its movement through the grommet beginning from the rear side until the cable stopper secures itself. Push the front section of the cable through the upper radiator support before fitting it to the displayed clamp positions. After aligning the hood cable with the hood lock lever you should lock the hood lock lever by using two claws for attachment. The Hood Lock Assembly installation requires MP grease on its sliding components followed by cable connection before bolting it down using two steel bolts along with one nut at 8.0 Nm (82 kgf-cm, 71 in-lbf). Install a fresh hood cap then affix the connector when operating with Theft Deterrent System equipment. The clamp should be attached to mount the Hood Lock Control Cable Cover while using a screw and a nut to lock it in place.

OEM Toyota Hood Cable

Hood Release Cable

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

219 Hood Cables found

View related parts
Toyota Release Cable, Front
Part Number: 53630-06100
$40.14 MSRP: $55.87
You Save: $15.73 (29%)
ADD TO CART
Product Specifications
- Other Name: Cable Assembly, Hood Lock; Hood Release Cable, Front; Cable Assembly, Hood Lock Control; Hood Release Cable
- Position: Front
- Replaces: 53630-33140
Fits the following Toyota Models:
- Camry | 2007-2011 | Base, CE, Hybrid, LE, SE, XLE | 4 Cyl 2.4 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.4 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 3.5 L GAS
View related parts
Toyota Release Handle
Part Number: 53601-89103-B0
$71.44 MSRP: $100.28
You Save: $28.84 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Lever Sub-Assembly, Hood; Lever; Lever Sub-Assembly, Hood Lock Control
- Manufacturer Note: MEDIUM GRAY,TRIM1#
- Replaces: 53601-89103-B1, 53601-04010-J0, 53601-89103-E1, 53601-04010-B0, 53601-89103-D0, 53601-89103-J0, 53601-89103-02, 53601-89103-E2, 53601-89103-03, 53601-89103-04, 53601-89103-E0
Fits the following Toyota Models:
- 4Runner | 1990-1995 | SR5 | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS
- T100 | 1993-1996 | Base, DLX, DX, One-Ton, One-Ton DLX, SR5 | 4 Cyl 2.7 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.4 L GAS
View related parts
Toyota Release Cable
Part Number: 53630-14300
$75.83 MSRP: $106.44
You Save: $30.61 (29%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Cable Assembly, Hood Lock; Hood Release Cable; Cable Assembly, Hood Lock Control
Fits the following Toyota Models:
- Supra | 1993-1998 | Base, Twin Turbo | 6 Cyl 3.0 L GAS
View related parts
Toyota Release Handle, Front
Part Number: 53611-02030-B0
$15.05 MSRP: $20.94
You Save: $5.89 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Lever, Hood Lock Control; Hood Release Handle, Front; Lever Sub-Assembly, Hood Lock Control
- Manufacturer Note: MD.CHARCOAL,TRIM1#
- Position: Front
Fits the following Toyota Models:
- Corolla | 1998-2002 | CE, LE, S, VE | 4 Cyl 1.8 L GAS
View related parts
Toyota Release Cable, Front
Part Number: 53630-33130
$42.65 MSRP: $59.36
You Save: $16.71 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assembly, Hood Lock; Hood Release Cable, Front; Cable Assembly, Hood Lock Control; Hood Release Cable
- Position: Front
Fits the following Toyota Models:
- Camry | 1997-2001 | CE, LE, XLE | 4 Cyl 2.2 L CNG, 4 Cyl 2.2 L GAS, 6 Cyl 3.0 L GAS
View related parts
Toyota Release Cable, Front
Part Number: 53630-02200
$35.84 MSRP: $49.89
You Save: $14.05 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assembly, Hood Lock; Hood Release Cable, Front; Cable Assembly, Hood Lock Control; Hood Release Cable
- Position: Front
Fits the following Toyota Models:
- Corolla | 2009-2013 | Base, L, LE, S, XLE, XRS | 4 Cyl 1.8 L GAS, 4 Cyl 2.4 L GAS
View related parts
Toyota Release Handle, Gray, Front
Part Number: 53601-02020-B9
$42.65 MSRP: $59.36
You Save: $16.71 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Lever Sub-Assembly, Hood; Hood Release Handle, Front; Lever Sub-Assembly, Hood Lock Control
- Manufacturer Note: NEUTRAL WARM GRAY,TRIM1#
- Position: Front
Fits the following Toyota Models:
- Camry | 2018-2019 | Hybrid LE, Hybrid SE, Hybrid XLE, L, LE, SE, XLE, XSE | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.5 L GAS
View related parts
Toyota Release Cable, Front
Part Number: 53630-02380
$34.28 MSRP: $47.72
You Save: $13.44 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assembly, Hood Lock; Hood Release Cable, Front; Cable Assembly, Hood Lock Control; Hood Release Cable
- Position: Front
- Replaces: 53630-12720
Fits the following Toyota Models:
- Corolla | 2019-2023 | Hybrid LE, Hybrid SE, Hybrid XLE, L, LE, SE, SE Apex, SE Nightshade, XLE, XSE, XSE Apex | 4 Cyl 1.8 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS
View related parts
Toyota Cable Assembly, Hood Lock Control, Front
Part Number: 53630-AA010
$37.92 MSRP: $52.78
You Save: $14.86 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assembly, Hood Lock; Hood Release Cable
- Position: Front
- Replaces: 53630-33100
Fits the following Toyota Models:
- Camry | 1997-2001 | CE, LE, XLE | 4 Cyl 2.2 L CNG, 4 Cyl 2.2 L GAS, 6 Cyl 3.0 L GAS
View related parts
Toyota Release Handle, Medium Gray, Front
Part Number: 53601-20060-B6
$63.09 MSRP: $88.55
You Save: $25.46 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Lever Sub-Assembly, Hood; Hood Release Handle, Front; Handle; Lever Sub-Assembly, Hood Lock Control
- Manufacturer Note: STONE,TRIM1#
- Position: Front
Fits the following Toyota Models:
- Land Cruiser | 2003-2007 | Base | 8 Cyl 4.7 L GAS
View related parts
Toyota Lever, Gray, Front
Part Number: 53601-01020-B5
$65.04 MSRP: $91.30
You Save: $26.26 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Lever Sub-Assembly, Hood; Hood Release Handle, Front; Lever Sub-Assembly, Hood Lock Control
- Manufacturer Note: DK.GRAY,TRIM12
- Position: Front
Fits the following Toyota Models:
- Tundra | 2003-2006 | Base, Limited, SR5 | 6 Cyl 3.4 L GAS, 6 Cyl 4.0 L GAS, 8 Cyl 4.7 L GAS
View related parts
Toyota Lever Sub-Assembly, Hood
Part Number: 53601-20060-C0
$75.00 MSRP: $105.27
You Save: $30.27 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: LEVER SUB-ASSY, HOOD
- Position: Front
- Replaces: 53601-20060-33, 53601-12030-03, 53601-12030-12, 53601-20060-A1, 53601-20060-B0, 53601-20060-36, 53601-12030-22, 53601-20060-04, 53601-20060-22, 53601-12030-02, 53601-20060-03, 53601-20060-05, 53601-20060-E0, 53601-20060-24, 53601-10020-B2, 53601-10020-B4, 53601-12030-14, 53601-10020-33, 53601-12030-04, 53601-20060-01, 53601-20060-11, 53601-20060-15, 53601-12030-01, 53601-20060-53, 53601-20060-B5, 53601-20060-32, 53601-20060-A0
Fits the following Toyota Models:
- 4Runner | 2001-2002 | Base, Limited, SR5 | 6 Cyl 3.4 L GAS
- Land Cruiser | 1991-2007 | Base | 6 Cyl 4.0 L GAS, 6 Cyl 4.5 L GAS, 8 Cyl 4.7 L GAS
- Previa | 1991-1994 | DX, LE | 4 Cyl 2.4 L GAS
- Supra | 1986-1992 | Base, Turbo | 6 Cyl 3.0 L GAS
View More
View related parts
Toyota Release Cable, Front
Part Number: 53630-10281
$34.28 MSRP: $47.72
You Save: $13.44 (29%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Cable Assembly, Hood Lock; Hood Release Cable, Front; Cable Assembly, Hood Lock Control; Hood Release Cable
- Position: Front
Fits the following Toyota Models:
- C-HR | 2019-2022 | LE, Limited, Nightshade, XLE | 4 Cyl 2.0 L GAS
View related parts
Toyota Release Handle, Front
Part Number: 53601-02020-B0
$54.00 MSRP: $75.17
You Save: $21.17 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Lever Sub-Assembly, Hood; Hood Release Handle, Front; Lever Sub-Assembly, Hood Lock Control
- Manufacturer Note: STONE,TRIM1#
- Position: Front
Fits the following Toyota Models:
- 4Runner | 2003-2009 | Limited, Sport, SR5 | 6 Cyl 4.0 L GAS, 8 Cyl 4.7 L GAS
- Corolla | 2003-2008 | CE, LE | 4 Cyl 1.8 L GAS
View related parts
Toyota Release Cable, Front
Part Number: 53630-12740
$34.28 MSRP: $47.72
You Save: $13.44 (29%)
ADD TO CART
Product Specifications
- Other Name: Cable Assembly, Hood Lock; Hood Release Cable, Front; Cable Assembly, Hood Lock Control; Hood Release Cable
- Position: Front
Fits the following Toyota Models:
- Corolla iM | 2017-2018 | Base | 4 Cyl 1.8 L GAS
View related parts
Toyota Release Cable, Front
Part Number: 53630-08040
$32.01 MSRP: $44.56
You Save: $12.55 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assembly, Hood Lock; Hood Release Cable, Front; Cable Assembly, Hood Lock Control; Hood Release Cable
- Position: Front
Fits the following Toyota Models:
- Sienna | 2021-2023 | 25th Anniversary Edition, LE, Limited, Platinum, XLE, XSE | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV)
View related parts
Toyota Release Cable, Front
Part Number: 53630-47070
$32.01 MSRP: $44.56
You Save: $12.55 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assembly, Hood Lock; Hood Release Cable, Front; Cable Assembly, Hood Lock Control; Hood Release Cable
- Position: Front
Fits the following Toyota Models:
- Prius V | 2012-2017 | Five, Four, Three, Two | 4 Cyl 1.8 L FULL HYBRID EV-GAS (FHEV)
View related parts
Toyota Release Cable, Front
Part Number: 53630-60210
$32.01 MSRP: $44.56
You Save: $12.55 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assembly, Hood Lock; Hood Release Cable, Front; Cable Assembly, Hood Lock Control; Hood Release Cable
- Position: Front
Fits the following Toyota Models:
- Land Cruiser | 2016-2021 | Base, Heritage Edition | 8 Cyl 5.7 L GAS
View related parts
Toyota Release Handle, Dark Gray, Front
Part Number: 53601-02020-B1
$46.47 MSRP: $64.68
You Save: $18.21 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Lever Sub-Assembly, Hood; Hood Release Handle, Front; Lever; Lever Sub-Assembly, Hood Lock Control
- Position: Front
Fits the following Toyota Models:
- Corolla | 2003-2013 | Base, L, LE, S, XLE, XRS | 4 Cyl 1.8 L GAS, 4 Cyl 2.4 L GAS
- FJ Cruiser | 2007-2011 | Base, Trail Teams Special Edition, TRD Special Edition | 6 Cyl 4.0 L GAS
- Matrix | 2003-2013 | Base, S, XR, XRS | 4 Cyl 1.8 L GAS, 4 Cyl 2.4 L GAS
- RAV4 | 2004-2012 | Base, L, Sport | 4 Cyl 2.4 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 3.5 L GAS
- Yaris | 2007-2012 | Base, S | 4 Cyl 1.5 L GAS
View More
View related parts
Toyota Release Lever, Beige, Front
Part Number: 53601-0C010-E1
$42.65 MSRP: $59.36
You Save: $16.71 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Lever Sub-Assembly, Hood; Hood Release Handle, Front; Release Handle; Lever Sub-Assembly, Hood Lock Control
- Manufacturer Note: SAND BEIGE,TRIM4#
- Position: Front
Fits the following Toyota Models:
- Sequoia | 2008-2020 | Limited, Platinum, SR5, TRD Pro, TRD Sport | 8 Cyl 4.6 L GAS, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L FLEX, 8 Cyl 5.7 L GAS
- Tundra | 2007-2013 | Base, Limited, Platinum, SR5 | 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L FLEX, 8 Cyl 5.7 L GAS

| Page 1 of 11 |Next >

1-20 of 219 Results

Toyota Hood Cable

OEM parts deliver unmatched quality you can rely on. They pass extensive quality control inspections. Toyota produces them to the official factory specifications. This process helps prevent defects and imperfections. So you can get exceptional lifespan and a flawless fit. Need new OEM Toyota Hood Cable? You'll love our wide selection of genuine options. Shop in minutes and skip the hunt. Our prices are unbeatable, you'll save time and money. It's easy to shop and find the right piece. Our committed customer service team gives professional help from start to finish. Every part includes a manufacturer's warranty. We ship quickly, your parts will arrive fast at your door.

Toyota Hood Cable connects the cabin lever with the latch and allows drivers to pop the hood fast. Toyota began in Japan in 1937 and continues to expand due to reduction of waste, fast-fixing issues, and perfecting the TNGA platform to more consolidated bodies, flatter cornering, and safer handling all over the world. Toyota accelerates hybrid development by increasing the electric range of plug-in systems and making that technology available in the majority of models to make fuel savings feel normal and the road trip last longer between refills. Toyota constructs vehicles that endure being beaten up each day, begin their days in the frozen dawn, and continue on their paths when odometers move into the six-digit circle, which generates loyalty that transcends a generation. Hood Cable remains concealed but acts on each drive, transmitting the pull force directly to the latch without stretching to open the hood on the first attempt. The cable employed by Hood Cable is a tough steel core with a smooth plastic coating that sheds off engine heat, road grit, moisture, and constant vibration. Hood Cable can only whimper when bent or rusted, so regular inspections of hanging strands or creaking movement maintain the release at its tightness. The owners of Toyota who change a frayed Hood Cable enjoy reduced lever feel and peace of mind whenever taking a quick roadside inspection or during normal fluid refill.

Toyota Hood Cable Parts and Q&A

Release Cable, Front
53630-06100
Q: How to service and repair a Hood Cable on Toyota Camry?
A:
The initial step for servicing the hood cable involves wheel removal followed by taking out the 3 extension pad screws from the front wheel opening. The 2GR-FE engine cool air intake duct seal must be removed before proceeding with the front bumper assembly disassembly process that requires separate instructions depending on fog light equipment. Next, remove the front fender liner through the combination of 5 clips and a bolt and 4 screws and a grommet. You need to eliminate the horn assembly with high-pitched sounds. The assembly of the hood lock without the engine hood courtesy switch needs a set of three bolts removal and hood lock control cable disconnection before extracting the assembly from its position. To detach the assembly including an engine hood courtesy switch personnel should first disconnect the connector afterward remove 3 bolts then disconnect the hood lock control cable before proceeding with removal of the assembly. The technician must first detach the hood lock control cable before taking out the hood lock control lever sub-assembly. After disconnecting the assembly clamps with a screwdriver, tape the screwdriver tip first before pulling the cable from the engine compartment.
Release Cable, Front
53630-0C020
Q: How to install the Hood Cable Assembly on Toyota Tundra?
A:
Pass the cable into the engine room and facilitate its movement through the grommet beginning from the rear side until the cable stopper secures itself. Push the front section of the cable through the upper radiator support before fitting it to the displayed clamp positions. After aligning the hood cable with the hood lock lever you should lock the hood lock lever by using two claws for attachment. The Hood Lock Assembly installation requires MP grease on its sliding components followed by cable connection before bolting it down using two steel bolts along with one nut at 8.0 Nm (82 kgf-cm, 71 in-lbf). Install a fresh hood cap then affix the connector when operating with Theft Deterrent System equipment. The clamp should be attached to mount the Hood Lock Control Cable Cover while using a screw and a nut to lock it in place.