How to remove the Hood Cable Assembly on Toyota Corolla?

The first step for Hood Cable Assembly removal involves removing the Radiator Grille Protector followed by taking out the No. 4 Engine Under Cover (for 2AZ-FE) and finally removing the Front Bumper Assembly. Begin by removing the Side Mudguard followed by the Front Wheel and Front Fender Liner which can be done with 8 clips and 3 screws then finish by taking out the 3 grommets although new grommets will be essential because the existing ones break upon extraction. Detach the Hood Lock Assembly by first removing three bolts and cutting the hood cable connection. The first step involves removing the Hood Lock Control Lever Sub-Assembly through disconnecting the hood cable. A screwdriver can be used to disconnect the Hood Cable Assembly clamps after taping the tip for protection and then draw the cable from the engine compartment for the removal.

How to install the hood cable assembly on Toyota Corolla?

The hood cable requires installation through the engine bay after passage through the upper radiator support for clamp attachment as depicted. The hood cable installation must be followed by attaching the hood lock control lever. Use MP grease for the sliding areas of the lock while installing the hood lock assembly using 3 bolts with the centering bolt received 7.5 Nm (77 kgf-cm, 66 in-lbf) torque and standard bolts reaching 8.0 Nm (82 kgf-cm, 71 in-lbf) torque. A post-installation check-up and adjustment of the hood sub-assembly should be performed. The front fender liner needs installation with new grommets and 3 screws which comes before installing 8 clips. Installation continues with the front wheel followed by side mudguard then front bumper assembly and No. 4 engine under cover (if equipped with 2AZ-FE) and radiator grille protector. Vehicles with fog lights require owners to prepare for adjustment and inspect the fog light aiming to achieve the right alignment.

OEM Toyota Corolla Hood Cable

Hood Release Cable

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

28 Hood Cables found

View related parts
Toyota Corolla Lever Sub-Assembly, Hood Lock Control, Front
Part Number: 53611-0E010-C0
$14.69 MSRP: $20.44
You Save: $5.75 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Lever, Hood Lock Control
- Manufacturer Note: BLACK,TRIM2#
- Position: Front
- Replaces: 53611-22010-C0, 53611-22010-B7, 53611-02030-C0, 53611-22010-B1
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2001-2002 Toyota Corolla | S | 4 Cyl 1.8 L GAS
View related parts
Toyota Corolla Release Cable, Front
Part Number: 53630-02280
$34.28 MSRP: $47.72
You Save: $13.44 (29%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Cable Assembly, Hood Lock; Hood Release Cable, Front; Cable Assembly, Hood Lock Control; Hood Release Cable
- Position: Front
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2014-2019 Toyota Corolla | 50th Anniversary Special Edition, L, LE, LE Eco, Le Eco Plus, S, SE, Special Edition, XLE, XSE | 4 Cyl 1.8 L GAS
View related parts
Toyota Corolla Release Cable
Part Number: 53630-12460
$46.35 MSRP: $64.52
You Save: $18.17 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assembly, Hood Lock; Hood Release Cable; Cable Assembly, Hood Lock Control
- Replaces: 53630-02010, 53630-12440
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1993-1997 Toyota Corolla | Base, CE, DX, LE | 4 Cyl 1.6 L GAS, 4 Cyl 1.8 L GAS
View related parts
Toyota Corolla Release Cable, Front
Part Number: 53630-02061
$39.90 MSRP: $55.53
You Save: $15.63 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assembly, Hood Lock; Hood Release Cable, Front; Cable Assembly, Hood Lock Control; Hood Release Cable
- Position: Front
- Replaces: 53630-02060
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2003-2008 Toyota Corolla | CE, LE, S, XRS | 4 Cyl 1.8 L GAS
View related parts
Toyota Corolla Release Cable, Front
Part Number: 53630-12610
$37.87 MSRP: $52.72
You Save: $14.85 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assembly, Hood Lock; Hood Release Cable, Front; Cable Assembly, Hood Lock Control; Hood Release Cable
- Position: Front
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2009-2013 Toyota Corolla | Base, L, LE, S, XLE, XRS | 4 Cyl 1.8 L GAS, 4 Cyl 2.4 L GAS
View related parts
Toyota Corolla Release Handle, Front
Part Number: 53601-02020-E0
$54.00 MSRP: $75.17
You Save: $21.17 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Lever Sub-Assembly, Hood; Hood Release Handle, Front; Lever Sub-Assembly, Hood Lock Control
- Manufacturer Note: MD.NEUTRAL BONE,TRIM4#
- Position: Front
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2003-2008 Toyota Corolla | CE, LE | 4 Cyl 1.8 L GAS
View related parts
Toyota Corolla Release Cable
Part Number: 53630-12721
$34.28 MSRP: $47.72
You Save: $13.44 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assembly, Hood Lock; Cable Assembly, Hood Lock Control
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2023-2024 Toyota Corolla | Hybrid LE, Hybrid SE, Hybrid XLE, LE, Nightshade, SE, XSE | 4 Cyl 1.8 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.0 L GAS
View related parts
Toyota Corolla Release Handle, Front
Part Number: 53611-02030-E0
$15.05 MSRP: $20.94
You Save: $5.89 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Lever, Hood Lock Control; Hood Release Handle, Front; Lever Sub-Assembly, Hood Lock Control
- Manufacturer Note: MD.NEUTRAL BONE,TRIM4#
- Position: Front
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1998-2002 Toyota Corolla | CE, LE, S, VE | 4 Cyl 1.8 L GAS
View related parts
Toyota Corolla Release Handle, Dark Gray, Front
Part Number: 53601-02020-B1
$46.47 MSRP: $64.68
You Save: $18.21 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Lever Sub-Assembly, Hood; Hood Release Handle, Front; Lever; Lever Sub-Assembly, Hood Lock Control
- Position: Front
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2003-2013 Toyota Corolla | Base, L, LE, S, XLE, XRS | 4 Cyl 1.8 L GAS, 4 Cyl 2.4 L GAS
View related parts
Toyota Corolla Release Handle, Front
Part Number: 53601-02020-B0
$54.00 MSRP: $75.17
You Save: $21.17 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Lever Sub-Assembly, Hood; Hood Release Handle, Front; Lever Sub-Assembly, Hood Lock Control
- Manufacturer Note: STONE,TRIM1#
- Position: Front
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2003-2008 Toyota Corolla | CE, LE | 4 Cyl 1.8 L GAS
View related parts
Toyota Corolla Release Handle, Beige/Brown, Front
Part Number: 53601-02020-E2
$46.47 MSRP: $64.68
You Save: $18.21 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Lever Sub-Assembly, Hood; Hood Release Handle, Front; Lever Sub-Assembly, Hood Lock Control
- Manufacturer Note: GREGE,TRIM4#
- Position: Front
- Replaces: 53601-52010-E4
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2009-2013 Toyota Corolla | Base, L, LE, S, XLE, XRS | 4 Cyl 1.8 L GAS, 4 Cyl 2.4 L GAS
View related parts
Toyota Corolla Release Lever, Gray, Front
Part Number: 53601-02020-B3
$42.65 MSRP: $59.36
You Save: $16.71 (29%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Lever Sub-Assembly, Hood; Hood Release Handle, Front; Release Handle; Lever; Lever Sub-Assembly, Hood Lock Control
- Position: Front
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2009-2013 Toyota Corolla | Base, L, LE, S, XLE, XRS | 4 Cyl 1.8 L GAS, 4 Cyl 2.4 L GAS
View related parts
Toyota Corolla Release Cable, Front
Part Number: 53630-02020
Product Specifications
- Other Name: Cable Assembly, Hood Lock; Hood Release Cable, Front; Cable Assembly, Hood Lock Control; Hood Release Cable
- Position: Front
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1998-2002 Toyota Corolla | CE, LE, S, VE | 4 Cyl 1.8 L GAS
View related parts
Toyota Corolla Release Handle, Front
Part Number: 53601-10020-C0
$70.50 MSRP: $98.95
You Save: $28.45 (29%)
Product Specifications
- Other Name: Lever Sub-Assembly, Hood; Hood Release Handle, Front; Lever; Lever Sub-Assembly, Hood Lock Control
- Position: Front
- Replaces: 53601-12020-13, 53601-10020-J0, 53601-10020-E5, 53601-10020-R9, 53601-10020-12, 53601-10020-D0, 53601-01010-P8, 53601-10020-24, 53601-10020-K0, 53601-01010-A1, 53601-10020-44, 53601-10020-E0, 53601-10020-01, 53601-12020-03, 53601-12020-06, 53601-12020-C0, 53601-10020-14, 53601-10020-B1, 53601-01010-J9, 53601-12020-05, 53601-10020-23, 53601-10020-E2, 53601-01020-B0, 53601-01020-E1, 53601-10020-05, 53601-10020-B0, 53601-10020-34, 53601-12020-04, 53601-10020-E3
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1988-1997 Toyota Corolla | Base, CE, DLX, DLX All Trac, DX, LE, SR5 All Trac | 4 Cyl 1.6 L GAS, 4 Cyl 1.8 L GAS
View related parts
Toyota Corolla Knob
Part Number: 53601-10020-22
Product Specifications
- Other Name: Lever Sub-Assembly, Hood Lock Control
- Manufacturer Note: RED,TRIM3#
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1988-1991 Toyota Corolla | GTS, SR5 | 4 Cyl 1.6 L GAS
View related parts
Toyota Corolla Release Cable
Part Number: 53630-12180
Product Specifications
- Other Name: Cable Assembly, Hood Lock; Hood Release Cable; Cable Assembly, Hood Lock Control
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1984-1988 Toyota Corolla | DLX, FX, FX16, FX16 GTS, LE, LE Limited, Sport DLX | 4 Cyl 1.6 L GAS, 4 Cyl 1.8 L DIESEL
View related parts
Toyota Corolla Release Cable
Part Number: 53630-12310
Product Specifications
- Other Name: Cable Assembly, Hood Lock; Hood Release Cable; Cable Assembly, Hood Lock Control
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1988-1989 Toyota Corolla | GTS, SR5 | 4 Cyl 1.6 L GAS
View related parts
Toyota Corolla Release Cable
Part Number: 53630-12220
Product Specifications
- Other Name: Cable Assembly, Hood Lock; Hood Release Cable; Cable Assembly, Hood Lock Control
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1984-1987 Toyota Corolla | Sport DLX, Sport GTS, Sport SR5 | 4 Cyl 1.6 L GAS
View related parts
Toyota Corolla Release Cable
Part Number: 53630-12340
Product Specifications
- Other Name: Cable Assembly, Hood Lock; Hood Release Cable; Cable Assembly, Hood Lock Control
- Replaces: 53630-12350, 53630-20160
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1990-1991 Toyota Corolla | Base, DLX, DLX All Trac, GTS, LE, SR5 | 4 Cyl 1.6 L GAS
View related parts
Toyota Corolla Release Cable
Part Number: 53630-12250
Product Specifications
- Other Name: Cable Assembly, Hood Lock; Hood Release Cable; Cable Assembly, Hood Lock Control
- Manufacturer Note: *86 & *87
- Replaces: 53630-01020
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1988-1992 Toyota Corolla | Base, DLX, DLX All Trac, FX, FX16, FX16 GTS, GTS, LE, SR5, SR5 All Trac | 4 Cyl 1.6 L GAS

| Page 1 of 2 |Next >

1-20 of 28 Results

Toyota Corolla Hood Cable

Choose genuine Hood Cable that pass strict quality control tests. You can trust the top quality and lasting durability. Shopping for OEM Hood Cable for your Toyota Corolla? Our website is your one-stop destination. We stock an extensive selection of genuine Toyota Corolla parts. The price is affordable so you can save more. It only takes minutes to browse and find the exact fit. Easily add to cart and check out fast. Our hassle-free return policy will keep you stress-free. We process orders quickly for swift delivery. Your parts will arrive faster, so you can get back on the road sooner.

Toyota Corolla Hood Cable Parts and Q&A

Release Cable, Front
53630-12610
Q: How to remove the Hood Cable Assembly on Toyota Corolla?
A:
The first step for Hood Cable Assembly removal involves removing the Radiator Grille Protector followed by taking out the No. 4 Engine Under Cover (for 2AZ-FE) and finally removing the Front Bumper Assembly. Begin by removing the Side Mudguard followed by the Front Wheel and Front Fender Liner which can be done with 8 clips and 3 screws then finish by taking out the 3 grommets although new grommets will be essential because the existing ones break upon extraction. Detach the Hood Lock Assembly by first removing three bolts and cutting the hood cable connection. The first step involves removing the Hood Lock Control Lever Sub-Assembly through disconnecting the hood cable. A screwdriver can be used to disconnect the Hood Cable Assembly clamps after taping the tip for protection and then draw the cable from the engine compartment for the removal.
Release Cable, Front
53630-02200
Q: How to install the hood cable assembly on Toyota Corolla?
A:
The hood cable requires installation through the engine bay after passage through the upper radiator support for clamp attachment as depicted. The hood cable installation must be followed by attaching the hood lock control lever. Use MP grease for the sliding areas of the lock while installing the hood lock assembly using 3 bolts with the centering bolt received 7.5 Nm (77 kgf-cm, 66 in-lbf) torque and standard bolts reaching 8.0 Nm (82 kgf-cm, 71 in-lbf) torque. A post-installation check-up and adjustment of the hood sub-assembly should be performed. The front fender liner needs installation with new grommets and 3 screws which comes before installing 8 clips. Installation continues with the front wheel followed by side mudguard then front bumper assembly and No. 4 engine under cover (if equipped with 2AZ-FE) and radiator grille protector. Vehicles with fog lights require owners to prepare for adjustment and inspect the fog light aiming to achieve the right alignment.