How to install the rear Sway Bar Kit and associated components on Toyota Camry?

The first step for installing the rear sway bar kit requires attaching the 2 rear sway bar bushings to the stopper ring located on the outside of the sway bar kit. Installation of the rear sway bar kit should begin with No. 2 bracket then continue with No. 1 bracket installation. Assemble the rear sway bar kit by tightening two bolts on each LN side with a torque value of 31 Nm (316 kgf-cm, 23 ft-lbf) and then do the same for the RH side. Use a 5 mm hexagon wrench to secure the stud if the ball joint turns when tightening the 2 nuts on the rear sway bar link assembly LH. Keep the torque at 39 Nm (398 kgf-cm, 29 ft-lbf). The installation of the rear sway bar link assembly RH requires the same protocol as the LH side. The next step involves installing the center exhaust pipe assembly which corresponds to either the 2AZ-FE or 2GR-FE while the next step requires using the tail exhaust pipe assembly which applies solely to the 2GR-FE. The rear wheels require installation with a torque setting of 103 Nm (1,050 kgf-cm, 76 ft-lbf), followed by complete examination of exhaust gas leaks.

How to remove the front Sway Bar Kit on Toyota Camry?

Begin sway bar kit removal by disconnecting the cable from the battery terminal then straighten the wheels before their removal. The next step should focus on separating both steering intermediate shaft assembly and tie rod end sub-assembly. The front sway bar link assembly LH requires the removal of its 2 nuts but if the ball joint moves with the nut in place then a 6 mm hexagon wrench should be used to secure the stud. The process for extracting the front sway bar link assembly RH should be repeated. Proceed to remove the engine assembly with transaxle according to the precise instructions for either a 2AZ-FE engine type or a 2GR-FE engine type. The removal process starts by unscrewing the 2 bolts on each of the front frame assembly brackets enjoying the front No. 1 sway bar bracket LH and RH. The procedure requires removal of the front sway bar bushings at the No. 1 locations and finally removing the sway bar kit itself.

OEM Toyota Camry Sway Bar Kit

Stabilizer Sway Bar Set

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

47 Sway Bar Kits found

View related parts
Toyota Camry Bar, Stabilizer, Rear
Part Number: 48812-33200
$186.50 MSRP: $266.29
You Save: $79.79 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sway Bar
- Position: Rear
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2005-2006 Toyota Camry | Base, LE, SE, XLE | 4 Cyl 2.4 L GAS, 6 Cyl 3.3 L GAS
View related parts
Toyota Camry Stabilizer Bar, Front
Part Number: 48811-33210
$101.07 MSRP: $141.87
You Save: $40.80 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bar, Stabilizer, Front; Sway Bar
- Position: Front
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2018-2019 Toyota Camry | SE | 4 Cyl 2.5 L GAS
View related parts
Toyota Camry Stabilizer Bar, Rear
Part Number: 48812-33030
$82.51 MSRP: $115.82
You Save: $33.31 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bar, Stabilizer, Rear; Sway Bar
- Manufacturer Note: (J)
- Position: Rear
- Replaces: 48812-06030
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1992-1996 Toyota Camry | DLX, DX, LE, SE, XLE | 4 Cyl 2.2 L GAS, 6 Cyl 3.0 L GAS
View related parts
Toyota Camry Stabilizer Bar, Front
Part Number: 48811-AA060
$137.70 MSRP: $194.92
You Save: $57.22 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bar, Stabilizer, Front; Suspension Stabilizer Bar, Front; Sway Bar
- Position: Front
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2002-2006 Toyota Camry | Base, LE, SE, XLE | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L GAS
View related parts
Toyota Camry Stabilizer Bar, Rear
Part Number: 48812-AC040
$102.85 MSRP: $144.36
You Save: $41.51 (29%)
ADD TO CART
Product Specifications
- Other Name: Bar, Stabilizer, Rear; Suspension Stabilizer Bar, Rear; Sway Bar
- Position: Rear
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2000-2001 Toyota Camry | LE, XLE | 6 Cyl 3.0 L GAS
View related parts
Toyota Camry Bar, Stabilizer, Rear
Part Number: 48812-06220
$77.37 MSRP: $108.60
You Save: $31.23 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sway Bar
- Position: Rear
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2020-2024 Toyota Camry | L, LE, SE, SE Nightshade, TRD, XLE, XSE | 4 Cyl 2.5 L GAS, 6 Cyl 3.5 L GAS
View related parts
Toyota Camry Stabilizer Bar, Front
Part Number: 48811-06150
$145.57 MSRP: $206.07
You Save: $60.50 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bar, Stabilizer, Front; Suspension Stabilizer Bar, Front; Sway Bar
- Position: Front
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2007-2011 Toyota Camry | SE | 4 Cyl 2.4 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 3.5 L GAS
View related parts
Toyota Camry Bar, Stabilizer, Front
Part Number: 48811-06350
$107.70 MSRP: $151.18
You Save: $43.48 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sway Bar
- Position: Front
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2020-2024 Toyota Camry | L, LE, SE, SE Nightshade, TRD, XLE, XSE | 4 Cyl 2.5 L GAS, 6 Cyl 3.5 L GAS
View related parts
Toyota Camry Stabilizer Bar, Front
Part Number: 48811-33140
$132.88 MSRP: $188.11
You Save: $55.23 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bar, Stabilizer; Suspension Stabilizer Bar, Front; Sway Bar; Bar, Stabilizer, Front
- Position: Front
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2002-2006 Toyota Camry | Base, LE, SE, XLE | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L GAS
View related parts
Toyota Camry Stabilizer Bar, Rear
Part Number: 48812-AA071
$86.23 MSRP: $121.05
You Save: $34.82 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bar, Stabilizer, Rear; Suspension Stabilizer Bar, Rear; Sway Bar
- Position: Rear
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2005-2006 Toyota Camry | Base, LE, SE, XLE | 4 Cyl 2.4 L GAS, 6 Cyl 3.3 L GAS
View related parts
Toyota Camry Stabilizer Bar, Front
Part Number: 48811-06241
$109.96 MSRP: $154.35
You Save: $44.39 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bar, Stabilizer, Front; Suspension Stabilizer Bar, Front; Sway Bar
- Position: Front
- Replaces: 48811-06240
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2012-2017 Toyota Camry | Hybrid LE, Hybrid SE, Hybrid XLE | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV)
View related parts
Toyota Camry Stabilizer Bar, Front
Part Number: 48811-AA020
$130.88 MSRP: $185.29
You Save: $54.41 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bar, Stabilizer, Front; Suspension Stabilizer Bar, Front; Sway Bar
- Manufacturer Note: OD=23
- Position: Front
- Replaces: 48811-33130
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2002-2006 Toyota Camry | Base, LE, SE, XLE | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS
View related parts
Toyota Camry Stabilizer Bar, Rear
Part Number: 48812-06090
$112.92 MSRP: $158.50
You Save: $45.58 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bar, Stabilizer, Rear; Suspension Stabilizer Bar, Rear; Sway Bar
- Position: Rear
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2007-2011 Toyota Camry | SE | 4 Cyl 2.4 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 3.5 L GAS
View related parts
Toyota Camry Stabilizer Bar, Rear
Part Number: 48812-AA090
$102.85 MSRP: $144.36
You Save: $41.51 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bar, Stabilizer, Rear; Suspension Stabilizer Bar, Rear; Sway Bar
- Manufacturer Note: MEXICO SPEC
- Position: Rear
- Replaces: 48812-33180
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2002-2006 Toyota Camry | LE, SE, XLE | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L GAS
View related parts
Toyota Camry Stabilizer Bar, Front
Part Number: 48811-33200
$90.78 MSRP: $127.43
You Save: $36.65 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bar, Stabilizer, Front; Sway Bar
- Position: Front
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2018-2019 Toyota Camry | LE | 4 Cyl 2.5 L GAS
View related parts
Toyota Camry Stabilizer Bar, Rear
Part Number: 48812-06200
$61.02 MSRP: $85.65
You Save: $24.63 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bar, Stabilizer, Rear; Suspension Stabilizer Bar, Rear; Sway Bar
- Position: Rear
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2012-2017 Toyota Camry | Hybrid LE, Hybrid SE, Hybrid XLE | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV)
View related parts
Toyota Camry Stabilizer Bar, Rear
Part Number: 48812-AA030
Product Specifications
- Other Name: Bar, Stabilizer, Rear; Suspension Stabilizer Bar, Rear; Sway Bar
- Position: Rear
- Replaces: 48812-33090
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2000-2003 Toyota Camry | CE, LE, SE, XLE | 4 Cyl 2.2 L CNG, 4 Cyl 2.2 L GAS, 4 Cyl 2.4 L GAS
View related parts
Toyota Camry Stabilizer Bar, Rear
Part Number: 48805-32010
Product Specifications
- Other Name: Bar Sub-Assembly, Rear Stabilizer; Sway Bar
- Position: Rear
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1984 Toyota Camry | DLX | 4 Cyl 1.8 L DIESEL
View related parts
Toyota Camry Stabilizer Bar, Rear
Part Number: 48805-32140
Product Specifications
- Other Name: Bar Sub-Assembly, Rear Stabilizer; Sway Bar
- Position: Rear
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1985-1986 Toyota Camry | DLX, LE | 4 Cyl 1.8 L DIESEL, 4 Cyl 2.0 L DIESEL, 4 Cyl 2.0 L GAS
View related parts
Toyota Camry Stabilizer Bar, Front
Part Number: 48811-32010
Product Specifications
- Other Name: Bar, Stabilizer, Front; Sway Bar
- Position: Front
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1984 Toyota Camry | DLX, LE | 4 Cyl 1.8 L DIESEL, 4 Cyl 2.0 L GAS

| Page 1 of 3 |Next >

1-20 of 47 Results

Toyota Camry Sway Bar Kit

Choose genuine Sway Bar Kit that pass strict quality control tests. You can trust the top quality and lasting durability. Shopping for OEM Sway Bar Kit for your Toyota Camry? Our website is your one-stop destination. We stock an extensive selection of genuine Toyota Camry parts. The price is affordable so you can save more. It only takes minutes to browse and find the exact fit. Easily add to cart and check out fast. Our hassle-free return policy will keep you stress-free. We process orders quickly for swift delivery. Your parts will arrive faster, so you can get back on the road sooner.

The Sway Bar Kit for the Toyota Camry cars is meant to improve the car's handling by linking opposite ends of the suspension. This kit is mainly used with an objective of minimizing the amount of lateral force applied to the car when cornering and over uneven surface. The Sway Bar Kit includes the anti-roll bar which employs a torsion spring to raise roll stiffness and in the meantime, decline sideways tilt or roll rate of the car, thereby increasing road grip. Different generations of Sway Bar Kits have been used in Camry models over the years, including adjustable as well as active anti-roll bars. Some of these advanced systems can give a variable stiffness so that handling and ride comfort can be tuned. The old design of the sway bar simply transmits the bumps from one wheel to the other, making the vehicle feel like it is ' waddling' when on rough grounds The modern design seen in most racing and high performance Toyota Camry vehicles use the sensors and hydraulics to make the real time adjustments.

Toyota Camry Sway Bar Kit Parts and Q&A

Stabilizer Bar, Rear
48812-06090
Q: How to install the rear Sway Bar Kit and associated components on Toyota Camry?
A:
The first step for installing the rear sway bar kit requires attaching the 2 rear sway bar bushings to the stopper ring located on the outside of the sway bar kit. Installation of the rear sway bar kit should begin with No. 2 bracket then continue with No. 1 bracket installation. Assemble the rear sway bar kit by tightening two bolts on each LN side with a torque value of 31 Nm (316 kgf-cm, 23 ft-lbf) and then do the same for the RH side. Use a 5 mm hexagon wrench to secure the stud if the ball joint turns when tightening the 2 nuts on the rear sway bar link assembly LH. Keep the torque at 39 Nm (398 kgf-cm, 29 ft-lbf). The installation of the rear sway bar link assembly RH requires the same protocol as the LH side. The next step involves installing the center Exhaust Pipe assembly which corresponds to either the 2AZ-FE or 2GR-FE while the next step requires using the tail exhaust pipe assembly which applies solely to the 2GR-FE. The rear wheels require installation with a torque setting of 103 Nm (1,050 kgf-cm, 76 ft-lbf), followed by complete examination of exhaust gas leaks.
Stabilizer Bar, Front
48811-06150
Q: How to remove the front Sway Bar Kit on Toyota Camry?
A:
Begin sway bar kit removal by disconnecting the cable from the battery terminal then straighten the wheels before their removal. The next step should focus on separating both steering intermediate shaft assembly and tie rod end sub-assembly. The front sway bar link assembly LH requires the removal of its 2 nuts but if the Ball Joint moves with the nut in place then a 6 mm hexagon wrench should be used to secure the stud. The process for extracting the front sway bar link assembly RH should be repeated. Proceed to remove the engine assembly with transaxle according to the precise instructions for either a 2AZ-FE engine type or a 2GR-FE engine type. The removal process starts by unscrewing the 2 bolts on each of the front frame assembly brackets enjoying the front No. 1 sway bar bracket LH and RH. The procedure requires removal of the front sway bar bushings at the No. 1 locations and finally removing the sway bar kit itself.