How to replace the Brake Pads on Toyota 4Runner?

First inspect the pad lining thickness after removing the front wheel through this order: Check if the lining thickness exceeds 1.0 mm (0.039 inch). Replace the pads when the minimum specification is not met. You must separate the clip from the parts along with 2 pins, anti-rattle spring, 2 pads, and 4 anti-squeal shims. However only reuse the anti-rattle spring if it maintains its original condition without damaging cracks and rust or dirt contamination. Conduct a disc measurement check alongside runout inspection before pad installation while you should substitute original anti-squeal shims with new pads. To install the new pads you should tape the monkey wrench handle in advance before pressing brake fluid from the reservoir while using the handle to push in the pistons for each wheel alone to avoid the opposite piston from flying out; loosening bleeder plugs when facing piston resistance allows brake fluid escape. Apply disc brake grease to the inside surfaces of new anti-squeal shims and install both shims in their appropriate positions before putting on the pads without permitting oil or grease to touch the pad contact surface. First install the anti-rattle spring then the two pins followed by the clip and ultimately reinstall the front wheel and tighten it to 103 Nm (1,050 kgf-cm, 76 ft. lbs.). Complete the brake pedal operation a few times to confirm that the fluid rests at the top mark.

How to Properly Replace a Brake Pads on Toyota Tacoma?

A mechanic must inspect driver brake pad lining thickness through the caliper inspection hole before pad replacement when lining reaches below 1.0 mm (0.039 inch). Lift the caliper into position by taking out the slide pin on the bottom side followed by a secure suspension that does not require flexible hose disconnect. First disconnect both brake pads together with four anti-squeal shims. After removing the pad wear indicator plate the support plates can be reused unless they show visible deformation or cracks or wear or have excessive rust or dirt. Measure disc thickness and runout before putting into place the four pad support plates. The procedure for installing new pads involves swapping both anti-squeal shims and wear indicator plates at the same time using the pads; the technician should install a pad wear indicator plate facing downward on the inner pad before securing two anti-squeal shims on each pad by applying disc brake grease to both sides of the inner anti-squeal shims. Start by placing the inner pad with its wear indicator plate pointing downwards before attaching the outer pad while making sure neither pad comes into contact with oil or grease on the rubbing surface. To press in the piston utilize a brake fluid suction from the reservoir followed by piston compression with appropriate tools such as a hammer handle or equivalent tools. Alternatively, if piston compression proves challenging loosen the bleeder plug to drain some brake fluid before using the compression tools. Apply the brake caliper inside while checking that the boot remains open and then install the slide pin with a torque setting of 88 Nm (900 kgf-cm, 65 ft. lbs.). The final task involves torquing the front wheel to 103 Nm (1,050 kgf-cm, 76 ft. lbs.) then you must press the brake pedal multiple times followed by verification that fluid reaches the maximum line.

OEM Toyota Brake Pads

Disc Brake Pad Set

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

213 Brake Pads found

View related parts
Toyota Pad Kit, Disc Brake, Rear Part Number: 04466-0E010
$51.98 MSRP: $72.00
You Save: $20.02 (28%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Disc Brake L; Disc Brake Pad Set; Brake Pads
- Manufacturer Note: MARK AK PA561
- Position: Rear
Fits the following Toyota Models:
- Highlander | 2014-2019 | Hybrid LE, Hybrid Limited, Hybrid Limited Platinum, Hybrid XLE, LE, LE Plus, Limited, Limited Platinum, SE, XLE | 4 Cyl 2.7 L GAS, 6 Cyl 3.5 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.5 L GAS
- Sienna | 2011-2020 | Base, L, LE, Limited, Limited Premium, SE, SE Premium, XLE, XLE Premium | 4 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS
View related parts
Toyota Pad Kit, Disc Brake, Front Part Number: 04465-35290
$75.25 MSRP: $104.50
You Save: $29.25 (28%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Disc Brake; Disc Brake Pad Set; Brake Pads
- Manufacturer Note: MARK SUMITOMO PS558H
- Position: Front
- Replaces: 04465-35250
Fits the following Toyota Models:
- 4Runner | 2003-2009 | Limited, Sport, SR5 | 6 Cyl 4.0 L GAS, 8 Cyl 4.7 L GAS
- FJ Cruiser | 2007-2014 | Base, Trail Teams Special Edition, TRD Special Edition | 6 Cyl 4.0 L GAS
- Sequoia | 2003-2007 | Limited, SR5 | 8 Cyl 4.7 L GAS
- Tundra | 2003-2006 | Base, Limited, SR5 | 6 Cyl 3.4 L GAS, 6 Cyl 4.0 L GAS, 8 Cyl 4.7 L GAS
View More
View related parts
Toyota Front Pads Part Number: 04465-0E010
$75.25 MSRP: $104.50
You Save: $29.25 (28%)
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Disc Brake L; Disc Brake Pad Set, Front; Disc Brake Pad Kit; Brake Pads; Pad Kit, Disc Brake, Front; Disc Brake Pad Set
- Manufacturer Note: MARK ADVICS PV565H
- Position: Front
Fits the following Toyota Models:
- Highlander | 2010-2019 | Base, Hybrid LE, Hybrid Limited, Hybrid Limited Platinum, Hybrid XLE, LE, LE Plus, Limited, Limited Platinum, Plus, SE, Sport, XLE | 4 Cyl 2.7 L GAS, 6 Cyl 3.5 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.5 L GAS
- Sienna | 2011-2020 | Base, L, LE, Limited, Limited Premium, SE, SE Premium, XLE, XLE Premium | 4 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS
View related parts
Toyota Brake Pads, Rear Part Number: 04466-60140
$52.57 MSRP: $72.80
You Save: $20.23 (28%)
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Disc Brake; Disc Brake Pad Set, Rear; Disc Brake Pad Kit; Rear Pads; Pad Kit, Disc Brake, Rear; Disc Brake Pad Set
- Manufacturer Note: MARK AK PA561
- Position: Rear
Fits the following Toyota Models:
- 4Runner | 2010-2024 | 40th Anniversary Edition, Limited, Nightshade, SR5, SR5 Premium, Trail, TRD Off-Road, TRD Off-Road Premium, TRD Pro, TRD Sport, Venture | 4 Cyl 2.7 L GAS, 6 Cyl 4.0 L GAS
View related parts
Toyota Brake Pads, Front Part Number: 04465-07010
$76.07 MSRP: $105.63
You Save: $29.56 (28%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Disc Brake; Disc Brake Pad Set, Front; Disc Brake Pad Kit; Front Pads; Pad Kit, Disc Brake, Front; Disc Brake Pad Set
- Manufacturer Note: MARK NBK D6911H
- Position: Front
Fits the following Toyota Models:
- Avalon | 2010-2015 | Base, Hybrid Limited, Hybrid XLE, Hybrid XLE Premium, Hybrid XLE Touring, Limited, XL, XLE, XLE Premium, XLE Touring, XLE Touring SE, XLS | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.5 L GAS
- Camry | 2010-2017 | Base, Hybrid LE, Hybrid SE, Hybrid XLE, L, LE, SE, SE Sport, Special Edition, XLE, XSE | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.5 L GAS
View related parts
Toyota Brake Pads, Rear Part Number: 04466-60090
$52.33 MSRP: $72.48
You Save: $20.15 (28%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Disc Brake; Disc Brake Pad Set, Rear; Brake Pad Set, Disc Brake; Disc Brake Pad Kit; Rear Pads; Shoes; Pad Kit, Disc Brake, Rear; Disc Brake Pad Set
- Manufacturer Note: MARK SUMITOMO PS549
- Position: Rear
- Replaces: 04466-60060
Fits the following Toyota Models:
- 4Runner | 2003-2009 | Limited, Sport, SR5 | 6 Cyl 4.0 L GAS, 8 Cyl 4.7 L GAS
- FJ Cruiser | 2007-2014 | Base, Trail Teams Special Edition, TRD Special Edition | 6 Cyl 4.0 L GAS
View related parts
Toyota Brake Pads, Rear Part Number: 04466-06200
$51.98 MSRP: $72.00
You Save: $20.02 (28%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Disc Brake; Disc Brake Pad Set, Rear; Disc Brake Pad Kit; Rear Pads; Pad Kit, Disc Brake, Rear; Disc Brake Pad Set
- Manufacturer Note: MARK NBK D6247
- Position: Rear
Fits the following Toyota Models:
- Avalon | 2013-2018 | Hybrid Limited, Hybrid XLE, Hybrid XLE Plus, Hybrid XLE Premium, Hybrid XLE Touring, Limited, Touring, XLE, XLE Plus, XLE Premium, XLE Touring, XLE Touring SE | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.5 L GAS
- Camry | 2012-2017 | Hybrid LE, Hybrid SE, Hybrid XLE, L, LE, SE, SE Sport, Special Edition, XLE, XSE | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.5 L GAS
View related parts
Toyota Brake Pads, Front Part Number: 04465-60320
$75.25 MSRP: $104.50
You Save: $29.25 (28%)
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Disc Brake; Disc Brake Pad Set, Front; Disc Brake Pad Kit; Front Pads; Pad Kit, Disc Brake, Front; Disc Brake Pad Set
- Manufacturer Note: MARK ADVICS PV565H
- Position: Front
Fits the following Toyota Models:
- 4Runner | 2010-2019 | Limited, SR5, SR5 Premium, Trail, TRD Off-Road, TRD Off-Road Premium, TRD Pro | 4 Cyl 2.7 L GAS, 6 Cyl 4.0 L GAS
View related parts
Toyota Brake Pads, Front Part Number: 04465-0E060
$75.25 MSRP: $104.50
You Save: $29.25 (28%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Disc Brake; Disc Brake Pad Set, Front; Front Pads; Pad Kit, Disc Brake, Front; Disc Brake Pad Set
- Manufacturer Note: MARK NBK D6994H
- Position: Front
Fits the following Toyota Models:
- Avalon | 2019-2022 | Hybrid Limited, Hybrid XLE, Hybrid XSE, Hybrid XSE Nightshade, Limited, Touring, TRD, XLE, XSE, XSE Nightshade | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.5 L GAS
- Camry | 2018-2023 | Hybrid LE, Hybrid SE, Hybrid SE Nightshade, Hybrid XLE, Hybrid XSE, L, LE, SE, SE Nightshade, XLE, XSE | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.5 L GAS
- RAV4 | 2019-2024 | Adventure, Hybrid LE, Hybrid Limited, Hybrid SE, Hybrid Woodland Edition, Hybrid XLE, Hybrid XLE Premium, Hybrid XSE, LE, Limited, TRD Off-Road, XLE, XLE Premium | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS
View More
View related parts
Toyota Pad Kit, Disc Brake, Rear Part Number: 04466-42060
$53.78 MSRP: $78.00
You Save: $24.22 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Disc Brake; Disc Brake Pad Set; Brake Pads
- Manufacturer Note: MARK ADVICS PS558
- Position: Rear
Fits the following Toyota Models:
- RAV4 | 2006-2018 | Adventure, Base, Hybrid Limited, Hybrid SE, Hybrid XLE, LE, Limited, Platinum, SE, Sport, XLE | 4 Cyl 2.4 L GAS, 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.5 L GAS
View related parts
Toyota Brake Pads, Rear Part Number: 04466-33210
$51.98 MSRP: $72.00
You Save: $20.02 (28%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Disc Brake; Disc Brake Pad Set, Rear; Disc Brake Pad Kit; Rear Pads; Pad Kit, Disc Brake, Rear; Disc Brake Pad Set
- Manufacturer Note: MARK AK NS542
- Position: Rear
Fits the following Toyota Models:
- Camry | 2018-2024 | L, LE, SE, SE Nightshade, TRD, XLE, XSE | 4 Cyl 2.5 L GAS, 6 Cyl 3.5 L GAS
View related parts
Toyota Brake Pads, Front Part Number: 04465-04070
$75.25 MSRP: $104.50
You Save: $29.25 (28%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Front Disc Brake; Disc Brake Pad Set, Front; Disc Brake Pad Kit; Front Pads; Pad Kit, Disc Brake, Front; Disc Brake Pad Set
- Manufacturer Note: MARK ADVICS PS558H
- Position: Front
Fits the following Toyota Models:
- Tacoma | 2005-2015 | Base, Pre Runner, TRD Pro, X-Runner | 4 Cyl 2.7 L GAS, 6 Cyl 4.0 L GAS
View related parts
Toyota Brake Pads, Front Part Number: 04465-08030
$76.07 MSRP: $105.63
You Save: $29.56 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Disc Brake; Disc Brake Pad Set, Front; Disc Brake Pad Kit; Front Pads; Pad Kit, Disc Brake, Front; Disc Brake Pad Set
- Manufacturer Note: MARK SELP PS558H
- Position: Front
Fits the following Toyota Models:
- Avalon | 2005-2007 | Limited, Touring, XL, XLS | 6 Cyl 3.5 L GAS
- Camry | 2005-2006 | LE, SE, XLE | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L GAS
- Sienna | 2004-2010 | CE, LE, Limited, XLE, XLE Limited | 6 Cyl 3.3 L GAS, 6 Cyl 3.5 L GAS
- Solara | 2004-2008 | SE, SE Sport, SLE, Sport | 4 Cyl 2.4 L GAS, 6 Cyl 3.3 L GAS
View More
View related parts
Toyota Pad Kit, Disc Brake, Rear Part Number: 04466-06090
$56.15 MSRP: $77.78
You Save: $21.63 (28%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Disc Brake; Disc Brake Pad Set; Brake Pads
- Manufacturer Note: MARK NBK D6247
- Position: Rear
- Replaces: 04466-33180, 04466-06060, 04466-33160
Fits the following Toyota Models:
- Avalon | 2008-2012 | Base, Limited, Touring, XL, XLS | 6 Cyl 3.5 L GAS
- Camry | 2007-2011 | Base, CE, Hybrid, LE, SE, XLE | 4 Cyl 2.4 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.4 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 3.5 L GAS
View related parts
Toyota Pad Kit, Disc Brake, Rear Part Number: 04466-60070
$57.23 MSRP: $79.27
You Save: $22.04 (28%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Disc Brake; Disc Brake Pad Set; Brake Pads
- Manufacturer Note: MARK AK PA511
- Position: Rear
- Replaces: 04466-60030, 04466-60100
Fits the following Toyota Models:
- Land Cruiser | 1998-2006 | Base | 8 Cyl 4.7 L GAS
View related parts
Toyota Pad Kit, Disc Brake, Front Part Number: 04465-06100
$76.07 MSRP: $105.63
You Save: $29.56 (28%)
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Disc Brake; Disc Brake Pad Set; Brake Pads
- Manufacturer Note: MARK NBK PN562H
- Position: Front
- Replaces: 04465-33450, 04465-06070, 04465-33440
Fits the following Toyota Models:
- Avalon | 2008-2010 | Limited, Touring, XL, XLS | 6 Cyl 3.5 L GAS
- Camry | 2007-2011 | Base, CE, Hybrid, LE, SE, XLE | 4 Cyl 2.4 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.4 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 3.5 L GAS
View related parts
Toyota Brake Pads, Rear Part Number: 04466-0C010
$53.78 MSRP: $78.00
You Save: $24.22 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Disc Brake; Disc Brake Pad Set, Rear; Disc Brake Pad Kit; Rear Pads; Pad Kit, Disc Brake, Rear; Disc Brake Pad Set
- Manufacturer Note: MARK ADVICS PS558H
- Position: Rear
Fits the following Toyota Models:
- Sequoia | 2008-2017 | Limited, Platinum, SR5 | 8 Cyl 4.6 L GAS, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L FLEX, 8 Cyl 5.7 L GAS
- Tundra | 2007-2017 | 1794 Edition, Base, Limited, Platinum, SR, SR5, TRD Pro | 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L FLEX, 8 Cyl 5.7 L GAS
View related parts
Toyota Brake Pads, Front Part Number: 04465-42200
$75.25 MSRP: $104.50
You Save: $29.25 (28%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Disc Brake; Disc Brake Pad Set, Front; Brake Pad Set, Disc Brake; Disc Brake Pad Kit; Pad Kit, Disc Brake, Front; Disc Brake Pad Set
- Manufacturer Note: MARK ADVICS PV565H
- Position: Front
- Replaces: 04465-42160
Fits the following Toyota Models:
- Prius V | 2012-2017 | Five, Four, Three, Two | 4 Cyl 1.8 L FULL HYBRID EV-GAS (FHEV)
- RAV4 | 2013-2018, 2006-2011 | Base, LE, Limited, Sport | 4 Cyl 2.4 L GAS, 4 Cyl 2.5 L GAS
View related parts
Toyota Brake Pads, Rear Part Number: 04466-02310
$53.78 MSRP: $78.00
You Save: $24.22 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Disc Brake; Disc Brake Pad Set, Rear; Rear Pads; Pad Kit, Disc Brake, Rear; Disc Brake Pad Set
- Position: Rear
- Replaces: 04466-02270, 04466-02260, 04466-02210
Fits the following Toyota Models:
- Corolla | 2014-2019, 2009-2010 | 50th Anniversary Special Edition, Base, L, LE, LE Eco, Le Eco Plus, S, SE, Special Edition, XLE, XRS, XSE | 4 Cyl 1.8 L GAS, 4 Cyl 2.4 L GAS
- Matrix | 2009-2013 | Base, S, XRS | 4 Cyl 1.8 L GAS, 4 Cyl 2.4 L GAS
View related parts
Toyota Brake Pads, Front Part Number: 04465-04090
$75.25 MSRP: $104.50
You Save: $29.25 (28%)
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Disc Brake; Disc Brake Pad Set, Front; Disc Brake Pad Kit; Front Pads; Pad Kit, Disc Brake, Front; Disc Brake Pad Set
- Manufacturer Note: MARK ADVICS VC070H
- Position: Front
Fits the following Toyota Models:
- Tacoma | 2016-2023 | Limited, SR, SR5, Trail, Trail Special Edition, TRD Off-Road, TRD Pro, TRD Sport | 4 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS

| Page 1 of 11 |Next >

1-20 of 213 Results

Toyota Brake Pads

OEM parts deliver unmatched quality you can rely on. They pass extensive quality control inspections. Toyota produces them to the official factory specifications. This process helps prevent defects and imperfections. So you can get exceptional lifespan and a flawless fit. Need new OEM Toyota Brake Pads? You'll love our wide selection of genuine options. Shop in minutes and skip the hunt. Our prices are unbeatable, you'll save time and money. It's easy to shop and find the right piece. Our committed customer service team gives professional help from start to finish. Every part includes a manufacturer's warranty. We ship quickly, your parts will arrive fast at your door.

Toyota Brake Pads bite hard and pull a vehicle down a pace with controlled and reliable capability. The trust Toyota has gained through the tiny waste on the line allows workers to see the trouble when it appears. Toyota continues to go all-hybrid, with plug-in Prius all the way to long-range RAV4, showing that being efficient and durable are not mutually exclusive. Toyota designed the TNGA platform to reduce weight, make bodies rigid, and enhance handling to ensure that each daily commute is nailed to the ground and secure. Options such as Hybrid Synergy Drive upgrade are added to more models annually and therefore even the entry-level trims do not gulp fuel like a thirsty camel. The outcome is a batch that is dependable, cost-effective, and can be applied on road trips of a decade without incident. The options of Toyota Brake Pads include non-metallic, semi-metallic, and ceramic mixtures all playing off stopping bite, rotor wear, dust output, and cabin quiet. Within each caliper, Brake Pads grip the spinning iron with a layer of friction, remove heat, and have wear tabs that squeal when the material is worn out. Brake Pads are optimal in swapping when new clips and springs slide in, and each pad is square and will not fade when applied many times. Maintain that between approximately 50,000-mile increments and the Brake Pads, the pedal feels firm and the stopping distance tight even after untold commute-hour crawls.

Toyota Brake Pads Parts and Q&A

Brake Pads, Front
04465-35240
Q: How to replace the Brake Pads on Toyota 4Runner?
A:
First inspect the pad lining thickness after removing the front wheel through this order: Check if the lining thickness exceeds 1.0 mm (0.039 inch). Replace the pads when the minimum specification is not met. You must separate the clip from the parts along with 2 pins, anti-rattle spring, 2 pads, and 4 anti-squeal shims. However only reuse the anti-rattle spring if it maintains its original condition without damaging cracks and rust or dirt contamination. Conduct a disc measurement check alongside runout inspection before pad installation while you should substitute original anti-squeal shims with new pads. To install the new pads you should tape the monkey wrench handle in advance before pressing brake fluid from the reservoir while using the handle to push in the pistons for each wheel alone to avoid the opposite piston from flying out; loosening bleeder plugs when facing piston resistance allows brake fluid escape. Apply disc brake grease to the inside surfaces of new anti-squeal shims and install both shims in their appropriate positions before putting on the pads without permitting oil or grease to touch the pad contact surface. First install the anti-rattle spring then the two pins followed by the clip and ultimately reinstall the front wheel and tighten it to 103 Nm (1,050 kgf-cm, 76 ft. lbs.). Complete the brake pedal operation a few times to confirm that the fluid rests at the top mark.
Brake Pads, Front
04465-04050
Q: How to Properly Replace a Brake Pads on Toyota Tacoma?
A:
A mechanic must inspect driver brake pad lining thickness through the caliper inspection hole before pad replacement when lining reaches below 1.0 mm (0.039 inch). Lift the caliper into position by taking out the slide pin on the bottom side followed by a secure suspension that does not require flexible hose disconnect. First disconnect both brake pads together with four anti-squeal shims. After removing the pad wear indicator plate the support plates can be reused unless they show visible deformation or cracks or wear or have excessive rust or dirt. Measure disc thickness and runout before putting into place the four pad support plates. The procedure for installing new pads involves swapping both anti-squeal shims and wear indicator plates at the same time using the pads; the technician should install a pad wear indicator plate facing downward on the inner pad before securing two anti-squeal shims on each pad by applying disc brake grease to both sides of the inner anti-squeal shims. Start by placing the inner pad with its wear indicator plate pointing downwards before attaching the outer pad while making sure neither pad comes into contact with oil or grease on the rubbing surface. To press in the piston utilize a brake fluid suction from the reservoir followed by piston compression with appropriate tools such as a hammer handle or equivalent tools. Alternatively, if piston compression proves challenging loosen the bleeder plug to drain some brake fluid before using the compression tools. Apply the brake caliper inside while checking that the boot remains open and then install the slide pin with a torque setting of 88 Nm (900 kgf-cm, 65 ft. lbs.). The final task involves torquing the front wheel to 103 Nm (1,050 kgf-cm, 76 ft. lbs.) then you must press the brake pedal multiple times followed by verification that fluid reaches the maximum line.