How to replace the front Brake Pads on Toyota Avalon?

You must inspect the pad lining through the caliper inspection hole first before pad replacement because the pad needs change if its thickness falls under 1.0 mm (0.039 inch). Raise the caliper when you detach both the bolt and flexible hose from the shock absorber bracket followed by the bottom side installation bolt then securely position the caliper while keeping the flexible hose connected. The brake pad replacement procedure needs the removal of two brake pads along with four anti-squeal shims and two pad support plates and the pad wear indicator plate. Support plates can be reused if they pass inspection by not showing any damage, cracks, wear, while remaining rust-free and dirt-free. The disc thickness check must be completed before installing both pad support plates. During new pad replacement install the wear indicator plates together with anti-squeal shims at the same time; place the indicator plate on inner pads followed by applying disc brake grease to both sides of the inner shims. Install two shims per pad. Install the pads starting with the inner pad which has the wear indicator plate upward while carefully avoiding friction surfaces from coming into contact with oil or grease. Installation of the caliper requires a small brake fluid drain from the reservoir then pressing the piston with a hammer handle or equivalent tool while unlatching the bleeder plug if required before caliper attachment. Betwixt holding the sliding pin and torquing the installation bolt to 34 Nm (350 kgf-cm, 25 ft. lbs.) reattach the flexible hose and bolt to the shock absorber bracket while torquing it to 29 Nm (300 kgf-cm, 21 ft. lbs.). To complete the installation replace the front wheel while tightening it to 103 Nm (1,050 kgf-cm, 76 ft. lbs.). Then press the brake pedal several times before checking the fluid level reaches the max line.

How to replace the rear Brake Pads on Toyota Avalon?

Begin by removing the rear wheel to check the pad lining thickness through the caliper inspection hole before pad replacement when the thickness reaches below 1.0 mm (0.039 inch). Secure the caliper in position after uninstalling the bottom side installation bolt and avoiding flexible hose removal. First remove the two brake pads together with their four anti-squeal shims and then proceed to remove the four pad support plates although these can be reused if they demonstrate no deformation wear or cracks and remain rust and dirt-free. Measure the disc thickness followed by checking its runout condition prior to installing the four pad support plates. The pad installation requires using new anti-squeal shims that must be greased on both sides before installing two shims on each pad while keeping the pads' wear indicator plates positioned downward and maintaining friction surfaces free from oil or grease. Use a hammer handle or corresponding tool to press the piston while the reservoir receives a small brake fluid drain. The tool should encounter resistance during this process so loosen the bleeder plug to let fluid escape as you continue inserting the piston. Close the caliper with the installed bolt before tightening it to 34 Nm (350 kgf-cm, 25 ft. lbs.). The final step involves reinstalling the rear wheel followed by torquing it to 103 Nm (1,050 kgf-cm, 76 ft. lbs.). Afterward, users should depress the brake pedal several times and verify that fluid reaches the maximum line.

OEM Toyota Avalon Brake Pads

Disc Brake Pad Set

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

14 Brake Pads found

View related parts
Toyota Avalon Brake Pads, Front Part Number: 04465-07010
$76.07 MSRP: $105.63
You Save: $29.56 (28%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Disc Brake; Disc Brake Pad Set, Front; Disc Brake Pad Kit; Front Pads; Pad Kit, Disc Brake, Front; Disc Brake Pad Set
- Manufacturer Note: MARK NBK D6911H
- Position: Front
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2010-2015 Toyota Avalon | Base, Hybrid Limited, Hybrid XLE, Hybrid XLE Premium, Hybrid XLE Touring, Limited, XL, XLE, XLE Premium, XLE Touring, XLE Touring SE, XLS | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.5 L GAS
View related parts
Toyota Avalon Brake Pads, Rear Part Number: 04466-06200
$51.98 MSRP: $72.00
You Save: $20.02 (28%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Disc Brake; Disc Brake Pad Set, Rear; Disc Brake Pad Kit; Rear Pads; Pad Kit, Disc Brake, Rear; Disc Brake Pad Set
- Manufacturer Note: MARK NBK D6247
- Position: Rear
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2013-2018 Toyota Avalon | Hybrid Limited, Hybrid XLE, Hybrid XLE Plus, Hybrid XLE Premium, Hybrid XLE Touring, Limited, Touring, XLE, XLE Plus, XLE Premium, XLE Touring, XLE Touring SE | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.5 L GAS
View related parts
Toyota Avalon Brake Pads, Front Part Number: 04465-0E060
$75.25 MSRP: $104.50
You Save: $29.25 (28%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Disc Brake; Disc Brake Pad Set, Front; Front Pads; Pad Kit, Disc Brake, Front; Disc Brake Pad Set
- Manufacturer Note: MARK NBK D6994H
- Position: Front
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2019-2022 Toyota Avalon | Hybrid Limited, Hybrid XLE, Hybrid XSE, Hybrid XSE Nightshade, Limited, Touring, TRD, XLE, XSE, XSE Nightshade | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.5 L GAS
View related parts
Toyota Avalon Brake Pads, Front Part Number: 04465-08030
$76.07 MSRP: $105.63
You Save: $29.56 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Disc Brake; Disc Brake Pad Set, Front; Disc Brake Pad Kit; Front Pads; Pad Kit, Disc Brake, Front; Disc Brake Pad Set
- Manufacturer Note: MARK SELP PS558H
- Position: Front
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2005-2007 Toyota Avalon | Limited, Touring, XL, XLS | 6 Cyl 3.5 L GAS
View related parts
Toyota Avalon Pad Kit, Disc Brake, Rear Part Number: 04466-06090
$56.15 MSRP: $77.78
You Save: $21.63 (28%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Disc Brake; Disc Brake Pad Set; Brake Pads
- Manufacturer Note: MARK NBK D6247
- Position: Rear
- Replaces: 04466-33180, 04466-06060, 04466-33160
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2008-2012 Toyota Avalon | Base, Limited, Touring, XL, XLS | 6 Cyl 3.5 L GAS
View related parts
Toyota Avalon Pad Kit, Disc Brake, Front Part Number: 04465-06100
$76.07 MSRP: $105.63
You Save: $29.56 (28%)
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Disc Brake; Disc Brake Pad Set; Brake Pads
- Manufacturer Note: MARK NBK PN562H
- Position: Front
- Replaces: 04465-33450, 04465-06070, 04465-33440
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2008-2010 Toyota Avalon | Limited, Touring, XL, XLS | 6 Cyl 3.5 L GAS
View related parts
Toyota Avalon Brake Pads, Rear Part Number: 04466-0E070
$51.98 MSRP: $72.00
You Save: $20.02 (28%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Disc Brake; Disc Brake Pad Set, Rear; Disc Brake Pad Kit; Rear Pads; Pad Kit, Disc Brake, Rear; Disc Brake Pad Set
- Manufacturer Note: MARK AK NS554
- Position: Rear
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2019-2022 Toyota Avalon | Hybrid Limited, Hybrid XLE, Hybrid XSE, Hybrid XSE Nightshade, Limited, Touring, TRD, XLE, XSE, XSE Nightshade | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.5 L GAS
View related parts
Toyota Avalon Brake Pads, Rear Part Number: 04466-06030
$57.23 MSRP: $79.27
You Save: $22.04 (28%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Disc Brake; Disc Brake Pad Set, Rear; Disc Brake Pad Kit; Rear Pads; Pad Kit, Disc Brake, Rear; Disc Brake Pad Set
- Manufacturer Note: MARK AK PA561
- Position: Rear
- Replaces: 04466-33080
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2005-2007 Toyota Avalon | Limited, Touring, XL, XLS | 6 Cyl 3.5 L GAS
View related parts
Toyota Avalon Pad Kit, Disc Brake, Front Part Number: 04465-33121
$76.89 MSRP: $106.79
You Save: $29.90 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Disc Brake; Disc Brake Pad Set; Brake Pads
- Manufacturer Note: MARK AK PA533
- Position: Front
- Replaces: 04465-33120
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1998-2004 Toyota Avalon | XL, XLS | 6 Cyl 3.0 L GAS
View related parts
Toyota Avalon Pad Kit, Disc Brake, Front Part Number: 04465-33060
$75.25 MSRP: $104.50
You Save: $29.25 (28%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Disc Brake Pad Set; Brake Pads
- Manufacturer Note: MARD AKEBONO PA533A
- Position: Front
- Replaces: 04465-06020, 04491-06020, 04491-07010, 04465-33010, 04491-33021, 04491-33020, 04491-33110, 04491-33100
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1995-1997 Toyota Avalon | XL, XLS | 6 Cyl 3.0 L GAS
View related parts
Toyota Avalon Brake Pads, Front Part Number: 04465-07020
$82.82 MSRP: $115.02
You Save: $32.20 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Disc Brake; Disc Brake Pad Set, Front; Disc Brake Pad Kit; Front Pads; Pad Kit, Disc Brake, Front; Disc Brake Pad Set
- Manufacturer Note: MARK NBK D6994H
- Position: Front
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2015-2018 Toyota Avalon | Hybrid Limited, Hybrid XLE Plus, Hybrid XLE Premium, Hybrid XLE Touring, Limited, Touring, XLE, XLE Plus, XLE Premium, XLE Touring, XLE Touring SE | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.5 L GAS
View related parts
Toyota Avalon Brake Pads, Front Part Number: 04465-33500
$85.19 MSRP: $119.58
You Save: $34.39 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Disc Brake; Disc Brake Pad Set, Front; Disc Brake Pad Kit; Front Pads; Pad Kit, Disc Brake, Front; Disc Brake Pad Set
- Manufacturer Note: MARK AKEBONO NS380H,TRD PACKAGE
- Position: Front
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2020-2022 Toyota Avalon | Hybrid XSE, Hybrid XSE Nightshade, TRD, XSE, XSE Nightshade | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.5 L GAS
View related parts
Toyota Avalon Brake Pads, Rear Part Number: 04466-41020
$57.23 MSRP: $79.27
You Save: $22.04 (28%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Disc Brake; Disc Brake Pad Set, Rear; Disc Brake Pad Kit; Rear Pads; Pad Kit, Disc Brake, Rear; Disc Brake Pad Set
- Manufacturer Note: MARK AK PA544
- Position: Rear
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2000-2004 Toyota Avalon | XL, XLS | 6 Cyl 3.0 L GAS
View related parts
Toyota Avalon Brake Pads, Rear Part Number: 04466-07020
$46.47 MSRP: $64.61
You Save: $18.14 (29%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Disc Brake; Disc Brake Pad Kit; Disc Brake Pad Set; Rear Pads; Pad Kit, Disc Brake, Rear
- Position: Rear
- Replaces: 04492-07010, 04466-07010, 04466-07011
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1995-1999 Toyota Avalon | XL, XLS | 6 Cyl 3.0 L GAS

Toyota Avalon Brake Pads

Choose genuine Brake Pads that pass strict quality control tests. You can trust the top quality and lasting durability. Shopping for OEM Brake Pads for your Toyota Avalon? Our website is your one-stop destination. We stock an extensive selection of genuine Toyota Avalon parts. The price is affordable so you can save more. It only takes minutes to browse and find the exact fit. Easily add to cart and check out fast. Our hassle-free return policy will keep you stress-free. We process orders quickly for swift delivery. Your parts will arrive faster, so you can get back on the road sooner.

Toyota Avalon Brake Pads offer the necessary friction to slow and stop the Avalon sedan by pushing against the brake rotors and transforming the movement into heat. These Brake Pads have a steel support plate with either molded or riveted friction coating, and two pads are clamped by a caliper on each rotor to complete the disc brake circuit. With worn-out Brake Pads, there is a minimum limit to the thickness, and the replacement is dictated by the electronic sensors or audible indicators that alert the driver before the safe limits are breached. Toyota states that Brake Pads should be regularly checked as it will ensure a consistent braking action and prevent rotor damage. Toyota owners have several Brake Pads formulations, which are non-metallic, semi-metallic, fully metallic, and ceramic compounds, each with a balance between wear resistance, operating noise, and heat management. Irrespective of the choice of materials, Toyota Avalon drivers should expect that the pads will lose lining material with each stop, which means that periodic renewal is an indispensable aspect of safe Avalon braking.

Toyota Avalon Brake Pads Parts and Q&A

Pad Kit, Disc Brake, Front
04465-33121
Q: How to replace the front Brake Pads on Toyota Avalon?
A:
You must inspect the pad lining through the caliper inspection hole first before pad replacement because the pad needs change if its thickness falls under 1.0 mm (0.039 inch). Raise the caliper when you detach both the bolt and flexible hose from the shock absorber bracket followed by the bottom side installation bolt then securely position the caliper while keeping the flexible hose connected. The brake pad replacement procedure needs the removal of two brake pads along with four anti-squeal shims and two pad support plates and the pad wear indicator plate. Support plates can be reused if they pass inspection by not showing any damage, cracks, wear, while remaining rust-free and dirt-free. The disc thickness check must be completed before installing both pad support plates. During new pad replacement install the wear indicator plates together with anti-squeal shims at the same time; place the indicator plate on inner pads followed by applying disc brake grease to both sides of the inner shims. Install two shims per pad. Install the pads starting with the inner pad which has the wear indicator plate upward while carefully avoiding friction surfaces from coming into contact with oil or grease. Installation of the caliper requires a small brake fluid drain from the reservoir then pressing the piston with a hammer handle or equivalent tool while unlatching the bleeder plug if required before caliper attachment. Betwixt holding the sliding pin and torquing the installation bolt to 34 Nm (350 kgf-cm, 25 ft. lbs.) reattach the flexible hose and bolt to the shock absorber bracket while torquing it to 29 Nm (300 kgf-cm, 21 ft. lbs.). To complete the installation replace the front wheel while tightening it to 103 Nm (1,050 kgf-cm, 76 ft. lbs.). Then press the brake pedal several times before checking the fluid level reaches the max line.
Brake Pads, Rear
04466-41020
Q: How to replace the rear Brake Pads on Toyota Avalon?
A:
Begin by removing the rear wheel to check the pad lining thickness through the caliper inspection hole before pad replacement when the thickness reaches below 1.0 mm (0.039 inch). Secure the caliper in position after uninstalling the bottom side installation bolt and avoiding flexible hose removal. First remove the two brake pads together with their four anti-squeal shims and then proceed to remove the four pad support plates although these can be reused if they demonstrate no deformation wear or cracks and remain rust and dirt-free. Measure the disc thickness followed by checking its runout condition prior to installing the four pad support plates. The pad installation requires using new anti-squeal shims that must be greased on both sides before installing two shims on each pad while keeping the pads' wear indicator plates positioned downward and maintaining friction surfaces free from oil or grease. Use a hammer handle or corresponding tool to press the piston while the reservoir receives a small brake fluid drain. The tool should encounter resistance during this process so loosen the bleeder plug to let fluid escape as you continue inserting the piston. Close the caliper with the installed bolt before tightening it to 34 Nm (350 kgf-cm, 25 ft. lbs.). The final step involves reinstalling the rear wheel followed by torquing it to 103 Nm (1,050 kgf-cm, 76 ft. lbs.). Afterward, users should depress the brake pedal several times and verify that fluid reaches the maximum line.