How to replace the front Brake Pads on Toyota Sequoia?

Check the pad lining thickness by removing the front wheel then inspect the measurement using a gauge to verify it exceeds 1.0 mm (0.039 inch) before continuing with the pad replacement. Release the clip and two pins and anti-rattle spring before disconnecting the two pads with their associated four shims. Anti-rattle spring and clip can be reused when they have no signs of deformation or cracks or wear and free of rust and dirt and external particles. You should verify the disc's thickness and runout before pad installation while replacing the anti-squeal shims with the new pads. Take out a little brake fluid from the reservoir before pushing the pistons in while using a monkey wrench handle or comparable tool which you need to cover with tape first. When replacing the pads choose to work on one wheel at a time to avoid having the opposing piston spring loose and if pushing the piston requires effort tighten the bleeder plug. Before placing the new pads' inner anti-squeal shims in position apply brake grease along their both sides but avoid permitting oil and grease to reach the pad's rubbing section. Install the new pads by first fastening the anti-rattle spring and 2 pins followed by the clip then reinstall the front wheel and tighten it to 110 Nm (1,150 kgf-cm, 82 ft. lbs.). End the procedure by pressing the brake pedal multiple times before verifying that the fluid marks the maximum line.

How to replace the rear Brake Pads on Toyota Sequoia?

The process starts with taking out the rear wheel followed by pad lining measurement through the caliper inspection hole. A pad replacement must happen when the lining measures under 1.0 mm (0.039 inch). Moving forward in the brake pad installation, remove the brake caliper through the process of removing its 2 sliding pins. Then suspend the caliper from place without unfastening the flexible hose. After removing the two pads and two anti-squeal shims pull out the four pad support plates but only reuse them if they remain free of defect and rust and dirt contamination. Measure the disc thickness and runout then install pad support plates and new pads while replacing anti-squeal shims with the pads. The pad wear indicator plate should be installed on new inner pads with a facing-down orientation before adding the outer pads while ensuring friction surfaces stay free from oil or grease. Draw out some brake fluid but only a small amount from the reservoir before using a hammer handle or equivalent tool to push in the pistons or loosen the bleeder plug for fluid release when pushing in the piston. Installation of the caliper depends on avoiding boot wedging while you apply lithium soap base glycol grease to the sliding pins before torquing them to 88 Nm (900 kgf-cm, 65 ft. lbs.). Install the rear wheel while torquing it to 110 Nm and then depress the brake pedal multiple times to verify the fluid reaches the max line.

OEM Toyota Sequoia Brake Pads

Disc Brake Pad Set

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

9 Brake Pads found

View related parts
Toyota Sequoia Pad Kit, Disc Brake, Front Part Number: 04465-35290
$75.25 MSRP: $104.50
You Save: $29.25 (28%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Disc Brake; Disc Brake Pad Set; Brake Pads
- Manufacturer Note: MARK SUMITOMO PS558H
- Position: Front
- Replaces: 04465-35250
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2003-2007 Toyota Sequoia | Limited, SR5 | 8 Cyl 4.7 L GAS
View related parts
Toyota Sequoia Brake Pads, Rear Part Number: 04466-0C010
$53.78 MSRP: $78.00
You Save: $24.22 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Disc Brake; Disc Brake Pad Set, Rear; Disc Brake Pad Kit; Rear Pads; Pad Kit, Disc Brake, Rear; Disc Brake Pad Set
- Manufacturer Note: MARK ADVICS PS558H
- Position: Rear
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2008-2017 Toyota Sequoia | Limited, Platinum, SR5 | 8 Cyl 4.6 L GAS, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L FLEX, 8 Cyl 5.7 L GAS
View related parts
Toyota Sequoia Brake Pads, Front Part Number: 04465-0C012
$75.37 MSRP: $102.31
You Save: $26.94 (27%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Disc Brake; Disc Brake Pad Set, Front; Disc Brake Pad Kit; Front Pads; Pad Kit, Disc Brake, Front; Disc Brake Pad Set
- Position: Front
- Replaces: 04465-0C011
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2001-2003 Toyota Sequoia | Limited, SR5 | 8 Cyl 4.7 L GAS
View related parts
Toyota Sequoia Brake Pads, Rear Part Number: 04466-02340
$63.12 MSRP: $88.61
You Save: $25.49 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Disc Brake; Disc Brake Pad Set, Rear; Disc Brake Pad Kit; Rear Pads; Pad Kit, Disc Brake, Rear; Disc Brake Pad Set
- Manufacturer Note: MARK ADVICS VC071
- Position: Rear
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2018-2022 Toyota Sequoia | Limited, Nightshade, Platinum, SR5, TRD Pro, TRD Sport | 8 Cyl 5.7 L FLEX, 8 Cyl 5.7 L GAS
View related parts
Toyota Sequoia Brake Pads, Front Part Number: 04465-02440
$93.09 MSRP: $130.67
You Save: $37.58 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Disc Brake; Disc Brake Pad Set, Front; Disc Brake Pad Kit; Front Pads; Pad Kit, Disc Brake, Front; Disc Brake Pad Set
- Manufacturer Note: MARK ADVICS VC070H
- Position: Front
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2018-2022 Toyota Sequoia | Limited, Nightshade, Platinum, SR5, TRD Pro, TRD Sport | 8 Cyl 5.7 L FLEX, 8 Cyl 5.7 L GAS
View related parts
Toyota Sequoia Brake Pads, Rear Part Number: 04466-60080
$62.20 MSRP: $87.30
You Save: $25.10 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Disc Brake; Disc Brake Pad Set, Rear; Disc Brake Pad Kit; Rear Pads; Pad Kit, Disc Brake, Rear; Disc Brake Pad Set
- Manufacturer Note: MARK NBK PN524-EE
- Position: Rear
- Replaces: 04466-60050
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2001-2007 Toyota Sequoia | Limited, SR5 | 8 Cyl 4.7 L GAS
View related parts
Toyota Sequoia Brake Pads, Front Part Number: 04465-0C020
$75.25 MSRP: $104.50
You Save: $29.25 (28%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Disc Brake; Disc Brake Pad Set, Front; Disc Brake Pad Kit; Front Pads; Pad Kit, Disc Brake, Front; Disc Brake Pad Set
- Manufacturer Note: MARK ADVICS PV565H
- Position: Front
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2008-2017 Toyota Sequoia | Limited, Platinum, SR5 | 8 Cyl 4.6 L GAS, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L FLEX, 8 Cyl 5.7 L GAS
View related parts
Toyota Sequoia Pad Kit, Disc Brake, Rear Part Number: 04466-60191
$62.20 MSRP: $87.31
You Save: $25.11 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Disc Brake
- Manufacturer Note: MARK ADVICS VC107
- Position: Rear
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2023-2025 Toyota Sequoia | 1794 Edition, Capstone, Limited, Platinum, SR5, TRD Pro | 6 Cyl 3.4 L FULL HYBRID EV-GAS (FHEV)
View related parts
Toyota Sequoia Brake Pads, Front Part Number: 04465-02580
$97.04 MSRP: $136.22
You Save: $39.18 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Disc Brake; Disc Brake Pad Set, Front; Front Pads; Pad Kit, Disc Brake, Front
- Manufacturer Note: MARK ADVICS VC084H
- Position: Front
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2023-2025 Toyota Sequoia | 1794 Edition, Capstone, Limited, Platinum, SR5, TRD Pro | 6 Cyl 3.4 L FULL HYBRID EV-GAS (FHEV)

Toyota Sequoia Brake Pads

Choose genuine Brake Pads that pass strict quality control tests. You can trust the top quality and lasting durability. Shopping for OEM Brake Pads for your Toyota Sequoia? Our website is your one-stop destination. We stock an extensive selection of genuine Toyota Sequoia parts. The price is affordable so you can save more. It only takes minutes to browse and find the exact fit. Easily add to cart and check out fast. Our hassle-free return policy will keep you stress-free. We process orders quickly for swift delivery. Your parts will arrive faster, so you can get back on the road sooner.

Toyota Sequoia Brake Pads offer the friction to decelerate and bring the vehicle to a stop by applying a force to the brake rotor and transforming motion into heat. In Toyota braking systems on the Sequoia, the Brake Pads are made of composite material consisting of a steel backing plate and a molded, bonded, or riveted friction compound that transfers the material to the rotor surface to form the grip needed during braking. Each rotor has two Brake Pads that are moved by a caliper whenever the pedal is pressed. Due to the natural wear of the lining, the Brake Pads should be changed when they become too thin, which can be indicated by audible sounds or electronic sensors that can warn the driver. Regular checks on any Toyota Sequoia would help avoid decreased braking power. The material formulations are also available in several different materials such as non-metallic, semi-metallic, fully metallic, and ceramic, allowing a tradeoff of friction, durability, and noise. The maintenance of fresh Brake Pads within the recommended service intervals helps to ensure a consistent stopping performance of all the Toyota Sequoia models that manufactures for use in normal driving scenarios.

Toyota Sequoia Brake Pads Parts and Q&A

Pad Kit, Disc Brake, Front
04465-35290
Q: How to replace the front Brake Pads on Toyota Sequoia?
A:
Check the pad lining thickness by removing the front wheel then inspect the measurement using a gauge to verify it exceeds 1.0 mm (0.039 inch) before continuing with the pad replacement. Release the clip and two pins and anti-rattle spring before disconnecting the two pads with their associated four shims. Anti-rattle spring and clip can be reused when they have no signs of deformation or cracks or wear and free of rust and dirt and external particles. You should verify the disc's thickness and runout before pad installation while replacing the anti-squeal shims with the new pads. Take out a little brake fluid from the reservoir before pushing the pistons in while using a monkey wrench handle or comparable tool which you need to cover with tape first. When replacing the pads choose to work on one wheel at a time to avoid having the opposing piston spring loose and if pushing the piston requires effort tighten the bleeder plug. Before placing the new pads' inner anti-squeal shims in position apply brake grease along their both sides but avoid permitting oil and grease to reach the pad's rubbing section. Install the new pads by first fastening the anti-rattle spring and 2 pins followed by the clip then reinstall the front wheel and tighten it to 110 Nm (1,150 kgf-cm, 82 ft. lbs.). End the procedure by pressing the brake pedal multiple times before verifying that the fluid marks the maximum line.
Brake Pads, Rear
04466-60080
Q: How to replace the rear Brake Pads on Toyota Sequoia?
A:
The process starts with taking out the rear wheel followed by pad lining measurement through the caliper inspection hole. A pad replacement must happen when the lining measures under 1.0 mm (0.039 inch). Moving forward in the brake pad installation, remove the Brake Caliper through the process of removing its 2 sliding pins. Then suspend the caliper from place without unfastening the flexible hose. After removing the two pads and two anti-squeal shims pull out the four pad support plates but only reuse them if they remain free of defect and rust and dirt contamination. Measure the disc thickness and runout then install pad support plates and new pads while replacing anti-squeal shims with the pads. The pad wear indicator plate should be installed on new inner pads with a facing-down orientation before adding the outer pads while ensuring friction surfaces stay free from oil or grease. Draw out some brake fluid but only a small amount from the reservoir before using a hammer handle or equivalent tool to push in the pistons or loosen the bleeder plug for fluid release when pushing in the piston. Installation of the caliper depends on avoiding boot wedging while you apply lithium soap base glycol grease to the sliding pins before torquing them to 88 Nm (900 kgf-cm, 65 ft. lbs.). Install the rear wheel while torquing it to 110 Nm and then depress the brake pedal multiple times to verify the fluid reaches the max line.