Corolla | 2005-2008 | CE, LE, S, XRS | 4 Cyl 1.8 L GAS
Highlander | 2005-2009 | Base, Hybrid, Hybrid Limited, Limited, Sport | 4 Cyl 2.4 L GAS, 4 Cyl 2.7 L GAS, 6 Cyl 3.3 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.3 L GAS, 6 Cyl 3.5 L GAS
Land Cruiser | 2006-2007 | Base | 8 Cyl 4.7 L GAS
Prius | 2004-2008 | Base, Touring | 4 Cyl 1.5 L FULL HYBRID EV-GAS (FHEV)
Corolla | 2021-2023 | Hybrid LE, Hybrid SE, Hybrid XLE, L, LE, SE, SE Nightshade, XLE, XSE | 4 Cyl 1.8 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS
GR Corolla | 2023 | Circuit Edition, Core, Morizo Edition | 3 Cyl 1.6 L GAS
Prius | 2021-2023 | 2020 Edition, L Eco, LE, Limited, XLE | 4 Cyl 1.8 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.0 L FULL HYBRID EV-GAS (FHEV)
Prius AWD-e | 2021-2023 | LE, Limited, XLE | 4 Cyl 1.8 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.0 L FULL HYBRID EV-GAS (FHEV)
Prius Prime | 2021-2023 | LE, Limited, SE, XLE, XSE, XSE Premium | 4 Cyl 1.8 L PLUG-IN HYBRID EV-GAS (PHEV), 4 Cyl 2.0 L PLUG-IN HYBRID EV-GAS (PHEV)
View More
| Page 1 of 3 |Next >
1-20 of 49 Results
Toyota Brake Light Switch Parts Questions & Experts Answers
Q: How to remove the brake light switch on Toyota Camry?
A: The brake light switch removal process starts by taking out the front door scuff plate followed by the cowl side trim sub-assembly and the lower instrument panel finish panel LH. First, uninstall the No. 1 instrument panel sub-assembly while also removing the lower instrument panel finish panel that accompanies the Smart Key System unless the system is absent where you should discard the lower panel accordingly. The worker must remove both the instrument cluster finish panel No. 1 and the combination meter. The stop light switch assembly connector must be disconnected from its assembly before turning the stop light switch assembly counterclockwise to detach it.
Q: How to remove the Brake Light Switch assembly on Toyota 4Runner?
A: The first step to separate the stop light switch assembly requires both the connector and wire harness clamp disconnection from the pedal support. The stop light switch must be unfastened counterclockwise to disengage it. Proceed by taking away the stop light switch mounting adjuster.
Q: How to install the Brake Light Switch on Toyota Tundra?
A: The installation of the stop light switch requires attaching two claws to the stop light switch mounting adjuster. The stop light switch needs installation to press against the pedal cushion with a force of under 98 N m (1000 kgf cm, 72.3 ft. lbf). Move the stop light switch through 90 degrees clockwise while the adjuster secures it together but the switch extends no more than 1 pitch when rotating. The stop light switch requires a torque setting of 1.5 N m (15 kgf cm, 13 in. lbf) during this process while ensuring silicon grease does not touch the switch. Finally, connect the connector.