How to install the Air Bag sensor assembly on 2008 Toyota Sequoia?

Begin the installation of the Air Bag sensor assembly only when the ignition switch is off and the negative battery terminal disconnected because skipping these steps can activate the Air Bag system. The SRS system needs a minimum of 90 seconds to become disabled after you disconnect the negative battery terminal. The front Air Bag sensor assembly must be installed using 3 bolts that reach a torque of 18 Nm (184 kgf-cm, 13 ft-lbf) while ensuring the sensor does not experience either a drop or impact. Check that the carpet clearance is proper for the plane beforeyou shake the front Air Bag sensor to check for looseness and then connect the connector holder to lock the lever into place. Check that both of the connectors remain protected on the drip-proof sheet without any evidence of cutting. Afterwards install the front console box followed by the rear console box assembly then the console box carpet and rear console box pocket along with the rear upper console panel sub-assembly and upper console panel sub-assembly then the shift lever knob sub-assembly and lower instrument panel finish panel sub-assembly LH the hood lock control lever sub-assembly and instrument side panel LH and front door opening trim Weather Strip LH front pillar garnish LH cowl side trim board LH and front door scuff plate LH. The last step involves attaching the cable to the negative battery terminal and tightening it to 5.4 Nm (55 kgf-cm, 48 in-lbf). Then check that the SRS warning light functions correctly.

OEM 2008 Toyota Sequoia Air Bag Sensor

Air Bag Impact Sensor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

5 Air Bag Sensors found

View related parts
2008 Toyota Sequoia Front Impact Sensor
Part Number: 89173-09480
$93.84 MSRP: $113.14
You Save: $19.30 (18%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor, Air Bag, Front; Air Bag Impact Sensor, Front; Air Bag Sensor; Front Sensor; Sensor, Air Bag, Front Passenger Side; Sensor, Air Bag, Front Driver Side
- Position: Front
- Item Weight: 0.70 Pounds
- Item Dimensions: 4.7 x 3.0 x 2.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 89173-09480
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2008 Toyota Sequoia Submodels:
- Limited, Platinum, SR5 | 8 Cyl 4.6 L GAS, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L FLEX, 8 Cyl 5.7 L GAS
View related parts
2008 Toyota Sequoia Position Sensor
Part Number: 89178-06040
$79.24 MSRP: $111.22
You Save: $31.98 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor, Seat Position; Front Left, Right, Left Track; Air Bag Seat Mat; Occupant Detection.; Air Bag Sensor; Occupant Sensor; Sensor; Sensor, Seat Position Air Bag
- Item Weight: 0.50 Pounds
- Item Dimensions: 2.1 x 1.5 x 1.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 89178-06040
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2008 Toyota Sequoia Submodels:
- Limited, Nightshade, Platinum, SR5, TRD Pro, TRD Sport | 8 Cyl 4.6 L GAS, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L FLEX, 8 Cyl 5.7 L GAS
View related parts
2008 Toyota Sequoia Position Sensor, Passenger Side
Part Number: 89178-06030
$79.24 MSRP: $111.22
You Save: $31.98 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor, Seat Position; Seat Track Position Sensor, Front/Right/Left; Air Bag Seat Sensor Mat; Occupant Detection Sensor; Air Bag Sensor; Occupant Sensor; Sensor, Seat Position Air Bag
- Position: Passenger Side
- Item Weight: 0.50 Pounds
- Item Dimensions: 2.0 x 1.6 x 1.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 89178-06030
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2008 Toyota Sequoia Submodels:
- Capstone, Limited, Platinum, SR5, TRD Pro | 6 Cyl 3.4 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 4.6 L GAS, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L FLEX, 8 Cyl 5.7 L GAS
View related parts
2008 Toyota Sequoia Side Impact Sensor
Part Number: 89831-0C050
$97.87 MSRP: $118.00
You Save: $20.13 (18%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor, Side Air Bag; Air Bag Sensor; Side Sensor; Sensor Assembly, Side Air Bag, Passenger Side; Sensor Assembly, Side Air Bag, Driver Side
- Item Weight: 0.60 Pounds
- Item Dimensions: 4.2 x 2.6 x 2.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 89831-0C050
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2008 Toyota Sequoia Submodels:
- Limited, Platinum, SR5 | 8 Cyl 4.6 L GAS, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L FLEX, 8 Cyl 5.7 L GAS
View related parts
2008 Toyota Sequoia Side Impact Sensor
Part Number: 89831-0C060
$122.54 MSRP: $173.47
You Save: $50.93 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor, Side Air Bag; Air Bag Sensor; Side Sensor; Sensor, Air Bag, Rear Passenger Side; Sensor, Air Bag, Rear Driver Side
- Item Weight: 0.60 Pounds
- Item Dimensions: 4.2 x 2.5 x 2.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 89831-0C060
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2008 Toyota Sequoia Submodels:
- Limited, Platinum, SR5 | 8 Cyl 4.6 L GAS, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L FLEX, 8 Cyl 5.7 L GAS

2008 Toyota Sequoia Air Bag Sensor

Looking for affordable OEM 2008 Toyota Sequoia Air Bag Sensor? Explore our comprehensive catalogue of genuine 2008 Toyota Sequoia Air Bag Sensor. All our parts are covered by the manufacturer's warranty. Plus, our straightforward return policy and speedy delivery service ensure an unparalleled shopping experience. We look forward to your visit!

2008 Toyota Sequoia Parts Questions & Experts Answers

Q: How to install the Air Bag sensor assembly on 2008 Toyota Sequoia?
A: Begin the installation of the Air Bag sensor assembly only when the ignition switch is off and the negative battery terminal disconnected because skipping these steps can activate the Air Bag system. The SRS system needs a minimum of 90 seconds to become disabled after you disconnect the negative battery terminal. The front Air Bag sensor assembly must be installed using 3 bolts that reach a torque of 18 Nm (184 kgf-cm, 13 ft-lbf) while ensuring the sensor does not experience either a drop or impact. Check that the carpet clearance is proper for the plane beforeyou shake the front Air Bag sensor to check for looseness and then connect the connector holder to lock the lever into place. Check that both of the connectors remain protected on the drip-proof sheet without any evidence of cutting. Afterwards install the front console box followed by the rear console box assembly then the console box carpet and rear console box pocket along with the rear upper console panel sub-assembly and upper console panel sub-assembly then the shift lever knob sub-assembly and lower instrument panel finish panel sub-assembly LH the hood lock control lever sub-assembly and instrument side panel LH and front door opening trim Weather Strip LH front pillar garnish LH cowl side trim board LH and front door scuff plate LH. The last step involves attaching the cable to the negative battery terminal and tightening it to 5.4 Nm (55 kgf-cm, 48 in-lbf). Then check that the SRS warning light functions correctly.