Other Name: Sensor, Side Air Bag; Air Bag Sensor; Side Sensor; Sensor Assembly, Side Air Bag, Passenger Side; Sensor Assembly, Side Air Bag, Driver Side
Warranty: This genuine part is guaranteed by Toyota's
factory warranty.
Fits the following Vehicles:
2008-2012 Toyota Sequoia | Limited, Platinum, SR5 | 8 Cyl 4.6 L GAS, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L FLEX, 8 Cyl 5.7 L GAS
Other Name: Sensor, Side Air Bag; Air Bag Impact Sensor, Rear; Air Bag Sensor; Impact Sensor; Side Air Bag Sensors for Driver and Passenger Sides, Rear Sensors Included.
Manufacturer Note: TAIWAN SPEC
Position: Rear
Warranty: This genuine part is guaranteed by Toyota's
factory warranty.
Fits the following Vehicles:
2023-2024 Toyota Sequoia | Capstone, Limited, Platinum, SR5, TRD Pro | 6 Cyl 3.4 L FULL HYBRID EV-GAS (FHEV)
Other Name: Sensor, Air Bag, Front; Air Bag Impact Sensor, Front; Air Bag Sensor; Front Sensor; Sensor, Air Bag, Front Passenger Side; Sensor, Air Bag, Front Driver Side
Manufacturer Note: TAIWAN SPEC
Position: Front
Warranty: This genuine part is guaranteed by Toyota's
factory warranty.
Fits the following Vehicles:
2023 Toyota Sequoia | Capstone, Limited, Platinum, SR5, TRD Pro | 6 Cyl 3.4 L FULL HYBRID EV-GAS (FHEV)
Other Name: Sensor Assembly, Side Air Bag; Air Bag Impact Sensor, Right; Side Sensor; Sensor Assembly, Side Air Bag, Passenger Side
Position: Passenger Side
Warranty: This genuine part is guaranteed by Toyota's
factory warranty.
Fits the following Vehicles:
2005-2007 Toyota Sequoia | Limited, SR5 | 8 Cyl 4.7 L GAS
| Page 1 of 2 |Next >
1-20 of 29 Results
Toyota Sequoia Air Bag Sensor
If you're thinking about purchasing OEM parts for your Toyota Sequoia, our website is your one-stop destination. We stock an extensive selection of genuine Toyota Sequoia Air Bag Sensor at pocket-friendly prices. Plus, we guarantee a swift delivery and a hassle-free return policy for your convenience.
Toyota Sequoia Air Bag Sensor Parts Questions & Experts Answers
Q: How to remove and install the Side and Curtain Shield Air Bag Sensor Assembly on Toyota Sequoia?
A: Starting the Side and Curtain Shield Air Bag Sensor Assembly removal process requires you to take out the rear door scuff plate alongside the front door scuff plate and front seat outer belt floor anchor and center pillar lower garnish. Then disconnect the connector from the side and curtain shield Air Bag sensor assembly while the assembly remains installed before removing the retractor of the front seat outer belt. To proceed with sensor assembly removal you must unfasten the three securing bolts. Always employ new SRS components for installation because you should not revisit sensors which were part of impacts or attempt to fix them. The side and curtain shield Air Bag assembly requires installation of the three bolts at 20 N.m (205 kgf.cm, 15 ft.lbf) at which point the connector can be attached after completing the sensor assembly installation. Verify that the connector maintains the required torque. You must replace the sensor assembly with new units whenever it shows defects or if it experienced a drop incident. Verify that no contact exists between SRS wiring and other system components or when wires are compressed. Verify that all sensor components are tight by performing a shaking test after finishing installation. The retractor of the front seat outer belt must be installed with 44 N.m (450 kgf.cm, 32 in.lbf) torque before moving onto center pillar lower garnish installation followed by front seat outer belt floor anchor using the same torque before installing front door scuff plate and rear door scuff plate.