How to service the side Air Bag sensor on the LH side on 2007 Toyota Sequoia?

A proper service of the LH side Air Bag sensor requires following the precautions in full detail. The negative battery terminal should undergo a 90-second disconnect before touching the connector to stop Air Bag initiation. The service requires removal of the front door scuff plate LH combined with the rear door scuff plate LH and center pillar garnish lower LH and front seat outer belt assembly. First disconnect the connector from the side Air Bag sensor LH followed by the removal of its supporting three bolts. The procedure requires a 90-second duration of turning off the ignition and disconnecting the negative terminal before beginning the work. The side Air Bag sensor LH installation must be completed with three bolts torquant to 17.5 N.m (179 kgf.cm, 13 ft.lbf). Discard and replace the sensor if it experiences either impact damage or shows any physical damage. Check that SRS wires do not get compressed by other components while inspecting for any installation looseness then reattach the connector to the side Air Bag sensor LH. Reinstallation of the required parts begins with the front seat outer belt assembly followed by center pillar garnish lower LH and then rear door scuff plate LH and completes with front door scuff plate LH. The cable must then be reattached to the negative battery terminal followed by initializations which become necessary when disconnecting the battery. The SRS warning light should be the last step for inspection.

OEM 2007 Toyota Sequoia Air Bag Sensor

Air Bag Impact Sensor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

7 Air Bag Sensors found

View related parts
2007 Toyota Sequoia Air Bag Sensor, Center
Part Number: 89170-0C142
$299.51 MSRP: $367.32
You Save: $67.81 (19%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor Assembly, Air Bag; Air Bag Impact Sensor, Center; Diagnostic Module
- Position: Center
- Replaces: 89170-0C141, 89170-0C140
- Item Weight: 2.20 Pounds
- Condition: New
- SKU: 89170-0C142
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2007 Toyota Sequoia Submodels:
- Limited, SR5 | 8 Cyl 4.7 L GAS
View related parts
2007 Toyota Sequoia Air Bag Sensor, Front Driver Side
Part Number: 89174-09040
$98.46 MSRP: $118.71
You Save: $20.25 (18%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor, Air Bag, Front; Air Bag Impact Sensor, Front Left, Left; Impact Sensor; Front Sensor; Sensor, Air Bag, Front Driver Side
- Position: Front Driver Side
- Part Name Code: 89174A
- Item Weight: 0.70 Pounds
- Item Dimensions: 4.7 x 2.9 x 2.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 89174-09040
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2007 Toyota Sequoia Submodels:
- Limited, SR5 | 8 Cyl 4.7 L GAS
View related parts
2007 Toyota Sequoia Air Bag Sensor, Front Passenger Side
Part Number: 89173-09200
$98.46 MSRP: $118.71
You Save: $20.25 (18%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor, Air Bag, Front; Air Bag Impact Sensor, Front Right, Right; Impact Sensor; Front Sensor; Sensor, Air Bag, Front Passenger Side
- Position: Front Passenger Side
- Part Name Code: 89173A
- Item Weight: 0.70 Pounds
- Item Dimensions: 4.7 x 2.9 x 2.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 89173-09200
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2007 Toyota Sequoia Submodels:
- Limited, SR5 | 8 Cyl 4.7 L GAS
View related parts
2007 Toyota Sequoia Air Bag Sensor, Rear Driver Side
Part Number: 89834-0C020
$120.97 MSRP: $171.24
You Save: $50.27 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor, Air Bag, Rear; Air Bag Impact Sensor, Rear Left; Side Sensor; Sensor, Air Bag, Rear Driver Side
- Position: Rear Driver Side
- Part Name Code: 89834
- Item Weight: 0.60 Pounds
- Item Dimensions: 4.3 x 2.6 x 2.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 89834-0C020
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2007 Toyota Sequoia Submodels:
- Limited, SR5 | 8 Cyl 4.7 L GAS
View related parts
2007 Toyota Sequoia Air Bag Sensor, Rear Passenger Side
Part Number: 89833-0C020
$284.66 MSRP: $406.42
You Save: $121.76 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor, Air Bag, Rear; Air Bag Impact Sensor, Rear Right; Side Sensor; Sensor, Air Bag, Rear Passenger Side
- Position: Rear Passenger Side
- Part Name Code: 89833
- Item Weight: 0.60 Pounds
- Item Dimensions: 4.2 x 2.6 x 2.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 89833-0C020
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2007 Toyota Sequoia Submodels:
- Limited, SR5 | 8 Cyl 4.7 L GAS
View related parts
2007 Toyota Sequoia Air Bag Sensor, Passenger Side
Part Number: 89860-0C040
Product Specifications
- Other Name: Sensor Assembly, Side Air Bag; Air Bag Impact Sensor, Right; Side Sensor; Sensor Assembly, Side Air Bag, Passenger Side
- Position: Passenger Side
- Part Name Code: 89860
- Item Weight: 0.60 Pounds
- Item Dimensions: 4.2 x 2.6 x 2.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 89860-0C040
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2007 Toyota Sequoia Submodels:
- Limited, SR5 | 8 Cyl 4.7 L GAS
View related parts
2007 Toyota Sequoia Air Bag Sensor, Driver Side
Part Number: 89830-0C040
Product Specifications
- Other Name: Sensor Assembly, Side Air Bag; Air Bag Impact Sensor, Left; Side Sensor; Sensor Assembly, Side Air Bag, Driver Side
- Position: Driver Side
- Part Name Code: 89860A
- Item Weight: 0.60 Pounds
- Item Dimensions: 4.3 x 2.6 x 2.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 89830-0C040
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2007 Toyota Sequoia Submodels:
- Limited, SR5 | 8 Cyl 4.7 L GAS

2007 Toyota Sequoia Air Bag Sensor

Looking for affordable OEM 2007 Toyota Sequoia Air Bag Sensor? Explore our comprehensive catalogue of genuine 2007 Toyota Sequoia Air Bag Sensor. All our parts are covered by the manufacturer's warranty. Plus, our straightforward return policy and speedy delivery service ensure an unparalleled shopping experience. We look forward to your visit!

2007 Toyota Sequoia Parts Questions & Experts Answers

Q: How to service the side Air Bag sensor on the LH side on 2007 Toyota Sequoia?
A: A proper service of the LH side Air Bag sensor requires following the precautions in full detail. The negative battery terminal should undergo a 90-second disconnect before touching the connector to stop Air Bag initiation. The service requires removal of the front door scuff plate LH combined with the rear door scuff plate LH and center pillar garnish lower LH and front seat outer belt assembly. First disconnect the connector from the side Air Bag sensor LH followed by the removal of its supporting three bolts. The procedure requires a 90-second duration of turning off the ignition and disconnecting the negative terminal before beginning the work. The side Air Bag sensor LH installation must be completed with three bolts torquant to 17.5 N.m (179 kgf.cm, 13 ft.lbf). Discard and replace the sensor if it experiences either impact damage or shows any physical damage. Check that SRS wires do not get compressed by other components while inspecting for any installation looseness then reattach the connector to the side Air Bag sensor LH. Reinstallation of the required parts begins with the front seat outer belt assembly followed by center pillar garnish lower LH and then rear door scuff plate LH and completes with front door scuff plate LH. The cable must then be reattached to the negative battery terminal followed by initializations which become necessary when disconnecting the battery. The SRS warning light should be the last step for inspection.