How to remove the front Sway Bar Kit on Toyota Sienna?

Removal of the front sway bar kit for 4WD begins with taking off the front wheels. Procedure for removing the front sway bar link assembly LH and front sway bar link assembly RH follows the same steps. Begin by eliminating the center exhaust pipe assembly then remove the two bolts from the No. 1 front sway bar bracket LH followed by the corresponding procedure on the No. 1 front sway bar bracket RH. Use Special Service Tool: 09628-62011 to divide the left-hand tie rod assembly then perform the same procedure for the right-hand tie rod assembly. The technician should use Tool: 09023-12701 to disassemble the pressure feed tube assembly before working on the steering intermediate shaft assembly. The first step demands the rack & pinion power steering gear assembly removal along with the manifold stay and finally the exhaust manifold sub-assembly RH. The end of the repair process includes removal of the No. 1 front sway bar bushing as well as the front sway bar kit.

How to install the front Sway Bar Kit on Toyota Sienna?

The installation of the front sway bar kit for 4WD requires the front sway bar kit to go first with the No. 1 front sway bar bushing positioned on the outer side of the bushing stopper on the sway bar kit while the slit must face towards the rear side of the vehicle. Start by installing the exhaust manifold sub-assembly RH then move on to manifold stay followed by steering intermediate shaft assembly and rack & pinion power steering gear assembly. The pressure feed tube assembly needs Special Service Tool: 09023-12701 to establish the connection before installing the tie rod assembly LH and RH. Remove the RH side using the same methods as the LH side installation. The installer should bolt both No. 1 front sway bar bracket LH and RH sections using two bolts with appropriate torques of 17 Nm (173 kgf-cm, 12 ft-lbf). Install and secure the center exhaust pipe assembly before installing front sway bar link assemblies at both LH and RH sides using the same installation procedures for each part. The last steps should include front wheel installation followed by checking the center front wheel alignment against the steering wheel center point before adding power steering fluid and bleeding the system and conducting a power steering fluid leak inspection.

OEM Toyota Sienna Sway Bar Kit

Stabilizer Sway Bar Set

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

13 Sway Bar Kits found

View related parts
Toyota Sienna Stabilizer Bar, Rear
Part Number: 48812-08030
$65.59 MSRP: $92.06
You Save: $26.47 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bar, Stabilizer, Rear; Suspension Stabilizer Bar, Rear; Sway Bar
- Manufacturer Note: MAAS PACKAGE
- Position: Rear
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2021-2023 Toyota Sienna | 25th Anniversary Edition, LE, Limited, Platinum, XLE, XSE | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV)
View related parts
Toyota Sienna Stabilizer Bar, Rear
Part Number: 48812-08020
$64.10 MSRP: $89.97
You Save: $25.87 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bar, Stabilizer, Rear; Suspension Stabilizer Bar, Rear; Sway Bar
- Position: Rear
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2021-2023 Toyota Sienna | 25th Anniversary Edition, LE, Limited, Platinum, XLE, XSE | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV)
View related parts
Toyota Sienna Stabilizer Bar, Front
Part Number: 48811-AE030
$154.22 MSRP: $218.31
You Save: $64.09 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bar, Stabilizer, Front; Suspension Stabilizer Bar, Front; Sway Bar
- Position: Front
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2004-2006 Toyota Sienna | CE, LE, Limited, XLE, XLE Limited | 6 Cyl 3.3 L GAS
View related parts
Toyota Sienna Stabilizer Bar, Front
Part Number: 48811-AE020
$147.92 MSRP: $209.40
You Save: $61.48 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bar, Stabilizer, Front; Suspension Stabilizer Bar, Front; Sway Bar
- Position: Front
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2004-2006 Toyota Sienna | CE, LE, Limited, XLE, XLE Limited | 6 Cyl 3.3 L GAS
View related parts
Toyota Sienna Stabilizer Bar, Front
Part Number: 48811-AE010
$89.41 MSRP: $125.50
You Save: $36.09 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bar, Stabilizer, Front; Suspension Stabilizer Bar, Front; Sway Bar
- Position: Front
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1998-2003 Toyota Sienna | CE, LE, XLE | 6 Cyl 3.0 L GAS
View related parts
Toyota Sienna Stabilizer Bar, Front
Part Number: 48811-08040
$130.41 MSRP: $184.61
You Save: $54.20 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bar, Stabilizer, Front; Suspension Stabilizer Bar, Front; Sway Bar
- Position: Front
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2011-2020 Toyota Sienna | Base, L, LE, Limited, Limited Premium, SE, SE Premium, XLE, XLE Premium | 4 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS
View related parts
Toyota Sienna Stabilizer Bar, Front
Part Number: 48811-08031
$127.83 MSRP: $180.96
You Save: $53.13 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bar, Stabilizer, Front; Suspension Stabilizer Bar, Front; Sway Bar
- Position: Front
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2014-2020 Toyota Sienna | L, LE, Limited, Limited Premium, SE, SE Premium, XLE, XLE Premium | 6 Cyl 3.5 L GAS
View related parts
Toyota Sienna Stabilizer Bar, Front
Part Number: 48811-08030
$124.77 MSRP: $176.64
You Save: $51.87 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bar, Stabilizer, Front; Suspension Stabilizer Bar, Front; Sway Bar
- Position: Front
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2011-2013 Toyota Sienna | Base, L, LE, Limited, SE, XLE | 6 Cyl 3.5 L GAS
View related parts
Toyota Sienna Stabilizer Bar, Front
Part Number: 48811-08020
$159.67 MSRP: $226.04
You Save: $66.37 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bar, Stabilizer, Front; Suspension Stabilizer Bar, Front; Sway Bar
- Position: Front
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2007-2010 Toyota Sienna | CE, LE, Limited, XLE | 6 Cyl 3.5 L GAS
View related parts
Toyota Sienna Stabilizer Bar, Front
Part Number: 48811-08010
$156.73 MSRP: $221.87
You Save: $65.14 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bar, Stabilizer, Front; Suspension Stabilizer Bar, Front; Sway Bar
- Position: Front
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2007-2010 Toyota Sienna | CE, LE, Limited, XLE | 6 Cyl 3.5 L GAS
View related parts
Toyota Sienna Stabilizer Bar, Front
Part Number: 48804-08021
$132.65 MSRP: $187.78
You Save: $55.13 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bar Sub-Assembly, Front Stabilizer; Bar, Stabilizer, Front
- Manufacturer Note: MAAS PACKAGE
- Position: Front
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2022-2023 Toyota Sienna | 25th Anniversary Edition, LE, Limited, Platinum, XLE, XSE | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV)
View related parts
Toyota Sienna Stabilizer Bar, Front
Part Number: 48804-08020
$136.05 MSRP: $192.60
You Save: $56.55 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bar Sub-Assembly, Front Stabilizer; Suspension Stabilizer Bar, Front; Sway Bar; Bar, Stabilizer, Front
- Manufacturer Note: MAAS PACKAGE
- Position: Front
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2021-2022 Toyota Sienna | LE, Limited, Platinum, XLE, XSE | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV)
View related parts
Toyota Sienna Stabilizer Bar, Front
Part Number: 48804-08011
$127.01 MSRP: $179.79
You Save: $52.78 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bar Sub-Assembly, Front Stabilizer; Suspension Stabilizer Bar, Front; Bar, Stabilizer, Front
- Position: Front
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2021-2023 Toyota Sienna | 25th Anniversary Edition, LE, Limited, Platinum, XLE, XSE | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV)

Toyota Sienna Sway Bar Kit

Choose genuine Sway Bar Kit that pass strict quality control tests. You can trust the top quality and lasting durability. Shopping for OEM Sway Bar Kit for your Toyota Sienna? Our website is your one-stop destination. We stock an extensive selection of genuine Toyota Sienna parts. The price is affordable so you can save more. It only takes minutes to browse and find the exact fit. Easily add to cart and check out fast. Our hassle-free return policy will keep you stress-free. We process orders quickly for swift delivery. Your parts will arrive faster, so you can get back on the road sooner.

The Sway Bar Kit is installed on the Toyota Sienna in order to improve its handling by linking sides of the suspensions system which are in the opposite order. This kit primarily is meant for lowering body roll in extreme cornering and over irregular surfaces, for increased stability. It works as an anti-roll bar inhibiting torsion and enabling the wheels to achieve a similar height so as to reduce lateral inclination and increase tractive demand. Different types of Sway Bar Kits have been incorporated in the Toyota Sienna as follows: adjustable and active anti-roll bars. These advanced systems can adjust the stiffness and provide better handing and comfort of the ride in the performances. Although the conventional sway bars enhance the handling it also passes on the shocks from one wheel to the other and this makes the ride less comfortable over the troublesome terrains. In total, the Sway Bar Kit can be considered as an important component for adjusting the Sienna's handling balance and its characteristics'.

Toyota Sienna Sway Bar Kit Parts and Q&A

Stabilizer Bar, Front
48811-08010
Q: How to remove the front Sway Bar Kit on Toyota Sienna?
A:
Removal of the front sway bar kit for 4WD begins with taking off the front wheels. Procedure for removing the front sway bar link assembly LH and front sway bar link assembly RH follows the same steps. Begin by eliminating the center Exhaust Pipe assembly then remove the two bolts from the No. 1 front sway bar bracket LH followed by the corresponding procedure on the No. 1 front sway bar bracket RH. Use Special Service Tool: 09628-62011 to divide the left-hand tie rod assembly then perform the same procedure for the right-hand tie rod assembly. The technician should use Tool: 09023-12701 to disassemble the pressure feed tube assembly before working on the steering intermediate shaft assembly. The first step demands the rack & pinion power steering gear assembly removal along with the manifold stay and finally the exhaust manifold sub-assembly RH. The end of the repair process includes removal of the No. 1 front sway bar bushing as well as the front sway bar kit.
Stabilizer Bar, Front
48811-08020
Q: How to install the front Sway Bar Kit on Toyota Sienna?
A:
The installation of the front sway bar kit for 4WD requires the front sway bar kit to go first with the No. 1 front sway bar bushing positioned on the outer side of the bushing stopper on the sway bar kit while the slit must face towards the rear side of the vehicle. Start by installing the exhaust manifold sub-assembly RH then move on to manifold stay followed by steering intermediate shaft assembly and rack & pinion power steering gear assembly. The pressure feed tube assembly needs Special Service Tool: 09023-12701 to establish the connection before installing the tie rod assembly LH and RH. Remove the RH side using the same methods as the LH side installation. The installer should bolt both No. 1 front sway bar bracket LH and RH sections using two bolts with appropriate torques of 17 Nm (173 kgf-cm, 12 ft-lbf). Install and secure the center Exhaust Pipe assembly before installing front sway bar link assemblies at both LH and RH sides using the same installation procedures for each part. The last steps should include front wheel installation followed by checking the center front wheel alignment against the steering wheel center point before adding power steering fluid and bleeding the system and conducting a power steering fluid leak inspection.

Related Toyota Sienna Parts

Browse Toyota Sienna Sway Bar Kit by Years

2023 2022 2021 2020 2019 2018 2017 2016 2015 2014 2013 2012 2011 2010 2009 2008 2007 2006 2005 2004 2003 2002 2001 2000 1999 1998