My Garage
Cart

OEM 2008 Toyota Sienna Sway Bar Kit

Stabilizer Sway Bar Set
  • Select Vehicle by Model
  • Select Vehicle by VIN
Select Vehicle by Model
Make
Model
Year
or
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

2 Sway Bar Kits found

  • 2008 Toyota Sienna Sway Bar Kit - 48811-08020
    2008 Toyota Sienna Sway Bar Kit Diagram - 48811-08020
    View related parts

    2008 Toyota Sienna Stabilizer Bar, Front

    Part Number: 48811-08020
    $151.68 MSRP: $214.72
    You Save: $63.04 (30%)
    Ships in 1-3 Business Days
    ADD TO CART
    Product Specifications
    • Other Name: Bar, Stabilizer, Front; Suspension Stabilizer Bar, Front; Sway Bar
    • Position: Front
    • Part Name Code: 48811
    • Item Weight: 7.80 Pounds
    • Item Dimensions: 43.4 x 12.2 x 4.9 inches
    • Condition: New
    • Fitment Type: Direct Replacement
    • SKU: 48811-08020
    • Warranty: This genuine part is guaranteed by Toyota's factory warranty.
    More Info
    Fits the following 2008 Toyota Sienna Submodels:
    • CE, LE, Limited, XLE | 6 Cyl 3.5 L GAS
  • 2008 Toyota Sienna Sway Bar Kit - 48811-08010
    2008 Toyota Sienna Sway Bar Kit Diagram - 48811-08010
    View related parts

    2008 Toyota Sienna Stabilizer Bar, Front

    Part Number: 48811-08010
    $148.86 MSRP: $210.73
    You Save: $61.87 (30%)
    Ships in 1-3 Business Days
    ADD TO CART
    Product Specifications
    • Other Name: Bar, Stabilizer, Front; Suspension Stabilizer Bar, Front; Sway Bar
    • Position: Front
    • Part Name Code: 48811
    • Item Weight: 8.10 Pounds
    • Item Dimensions: 42.9 x 12.0 x 5.0 inches
    • Condition: New
    • Fitment Type: Direct Replacement
    • SKU: 48811-08010
    • Warranty: This genuine part is guaranteed by Toyota's factory warranty.
    More Info
    Fits the following 2008 Toyota Sienna Submodels:
    • CE, LE, Limited, XLE | 6 Cyl 3.5 L GAS

2008 Toyota Sienna Sway Bar Kit

Looking for affordable OEM 2008 Toyota Sienna Sway Bar Kit? Explore our comprehensive catalogue of genuine 2008 Toyota Sienna Sway Bar Kit. All our parts are covered by the manufacturer's warranty. Plus, our straightforward return policy and speedy delivery service ensure an unparalleled shopping experience. We look forward to your visit!

2008 Toyota Sienna Parts Questions & Experts Answers

  • Q: How to install the front Sway Bar Kit on 2008 Toyota Sienna?
    A: The installation of the front sway bar kit for 4WD requires the front sway bar kit to go first with the No. 1 front sway bar bushing positioned on the outer side of the bushing stopper on the sway bar kit while the slit must face towards the rear side of the vehicle. Start by installing the exhaust manifold sub-assembly RH then move on to manifold stay followed by steering intermediate shaft assembly and rack & pinion power steering gear assembly. The pressure feed tube assembly needs Special Service Tool: 09023-12701 to establish the connection before installing the tie rod assembly LH and RH. Remove the RH side using the same methods as the LH side installation. The installer should bolt both No. 1 front sway bar bracket LH and RH sections using two bolts with appropriate torques of 17 Nm (173 kgf-cm, 12 ft-lbf). Install and secure the center exhaust pipe assembly before installing front sway bar link assemblies at both LH and RH sides using the same installation procedures for each part. The last steps should include front wheel installation followed by checking the center front wheel alignment against the steering wheel center point before adding power steering fluid and bleeding the system and conducting a power steering fluid leak inspection.

Related 2008 Toyota Sienna Parts