Other Name: Belt Assembly, Rear Seat; Seat Belt Lap and Shoulder Belt, Rear Left; Belt & Retractor; Belt Assembly, Rear Seat 3 Point Type, Outer Driver Side
Other Name: Belt Assembly, Rear Seat; Seat Belt Lap and Shoulder Belt, Rear Left Outer; Outer Belt Assembly; Belt Assembly, Rear Seat, Outer Driver Side
Other Name: Belt Assembly, Rear Seat; Seat Belt Lap and Shoulder Belt, Rear Right; Belt & Retractor; Belt Assembly, Rear Seat 3 Point Type, Outer Passenger Side
Other Name: Belt Assembly, Rear Seat 3; Seat Belt Lap and Shoulder Belt, Rear Inner; Center Seat Belt; Belt Assembly, Rear Seat 3 Point Type, Passenger Side
Q: What are the essential components of the rear Seat Belt assembly and why is regular inspection important on Scion tC?
A: The rear seat outer belt assembly functions by multiple crucial components which guarantee operational safety. The safety standards require regular checks with proper maintenance of these components to ensure proper operation. A quick response to all signs of wear or damage will help keep the seat belt system in impeccable condition.
Q: How to replace the front seat belt on Scion xA?
A: The battery negative terminal should be disconnected as the first step for front seat belt replacement. The removal process begins with taking out the front seat assembly RH then proceeding to remove the front seat inner belt assembly RH which needs its bolt and inner belt detached. You need to remove the front door scuff plate RH, rear door scuff plate RH, front door opening trim Weather Strip RH and rear door opening trim Weather Strip RH as well as the center pillar garnish lower RH. The operation to remove the front seat belt with pretensioner can begin only after the battery disconnect and ignition shut off happens 90 seconds ago. To begin dismount the floor anchor cover before disconnecting bolt and outer belt on the floor anchor side and subsequently move to the shoulder anchor cover and its bolt and outer belt before disconnecting the pretensioner connector. Mount removal is possible when all two bolts from the retractor side are removed. When installing the outer belt avoid separating the retractor components while verifying ELR lock operation at different tilt angles since locking should occur with at least 45 degrees but not below 15 degrees. When installing the outer belt to the retractor side you need to tighten the upper bolt to 5.5 Nm (51 kgf.cm, 44 in.lbf) while using 42 Nm (430 kgf.cm, 31 ft.lbf) for the lower bolt. The pretensioner connector should be connected and the outer belt gets installed on the shoulder anchor side first before torquing it with 42 Nm force (430 kgf.cm, 31 ft.lbf). Next follows installation of the shoulder anchor cover and outer belt with floor anchor side bolt tightened to 42 Nm force (430 kgf.cm, 31 ft.lbf). Continue by attaching the floor anchor cover and verify the ELR lock function by fast-pulling the belt shortly following completion. The belt must secure properly while testing child restraint fastening to ensure the belt only rewinds when fully extended so it can easily move in and out after maximum extension. The outer belt assembly must get replaced if any operation does not perform according to specification. Reinstall the front seat assembly RH after putting the bolt into the front seat inner belt assembly RH and torquing it to 42 Nm (430 kgf.cm, 31 ft.lbf).
Q: How to remove the rear center Seat Belt assembly on Scion xB?
A: The process to remove the rear center seat outer belt assembly starts with taking out the rear seat cushion cover pad sub-assembly then continuing with the removal of the rear seatback assembly. The removal process starts with the rear seat headrest assembly and continues to the seat belt anchor cover cap and the rear seat shoulder belt cover. Secondly uninstall the rear seat back lock release button while removing the rear seat back stop button grommet. The technician should disassemble the rear seat back cover RH together with the rear seat headrest support. The frame sub-assembly should be taken out first to perform the removal of the rear center seat outer belt assembly using bolt extraction and hook dissolution with retractor withdrawal.