How to reassemble the axle shaft on 2008 Toyota Highlander?

The front drive shaft bearing assembly process for 2WD RH side starts with a new bearing bracket hole snap ring installation into the front drive shaft assembly RH followed by Special Service Tool: 09527-30010 09527-10011 usage to install a new front drive shaft bearing with complete insertion. The next step includes a new drive shaft hole snap ring installation by using a snap ring expander. A new drive shaft dust cover should be installed using Special Service Tool: 09726-40010 09527-10011 and a press until it achieves full installation without damage and the same procedure must be repeated for RH and LH dust covers at a distance of 109.0 to 110.0 mm on the RH cover. Repeat the installation procedure applied to the LH side for the 4WD RH side. The installation sequence for the front axle outboard joint boot consists of fitting the No. 2 front axle outboard joint boot clamp followed by the front axle outboard joint boot and finally the front axle outboard joint boot clamp in that order while applying grease to the joint. This procedure must be completed after wrapping the drive shaft splines with vinyl tape for protection. Before fastening the front axle outboard joint boot clamp to the drive shaft in a vise you need Special Service Tool: 09521-24010 to pinch it. Check the clearance which should be between 0.5 to 1.5 mm. Apply the same measurement steps to the No. 2 front axle outboard joint boot clamp. Place the drive shaft damper in the correct position before installing the drive shaft damper clamp while maintaining the same measurement technique for the clearance as before. The front drive inboard joint assembly requires vinyl tape on the splines followed by front axle inboard joint boot clamp then front axle inboard joint boot and lastly No. 2 front axle inboard joint boot clamp in sequence to achieve correct tripod joint installation without roller impacts while packing with grease. You should start by installing the front axle inboard joint boot and its clamps before checking the clearance value and placing the new front drive shaft hole snap ring.

OEM 2008 Toyota Highlander Axle Shaft

Car Axle Shaft

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

9 Axle Shafts found

View related parts
2008 Toyota Highlander Shaft Assembly, Front Drive
Part Number: 43420-0W280
$558.34 MSRP: $844.78
You Save: $286.44 (34%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: SHAFT ASSY, FR DRIVE; CV Axle Assembly; Axle Shaft
- Position: Front Driver Side
- Replaces: 43420-0W230
- Item Weight: 14.40 Pounds
- Item Dimensions: 31.6 x 7.6 x 6.7 inches
- Condition: New
- SKU: 43420-0W280
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2008 Toyota Highlander Submodels:
- Hybrid, Hybrid Limited | 6 Cyl 3.3 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.5 L FULL HYBRID EV-GAS (FHEV)
View related parts
2008 Toyota Highlander Axle Assembly, Passenger Side
Part Number: 43410-0W200
$428.79 MSRP: $628.40
You Save: $199.61 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Front Drive; CV Axle Assembly, Front Right; GSP Cv Axle; Axle Shaft; Shaft Assembly, Front Drive, Passenger Side; CV Axle Assembly
- Position: Passenger Side
- Part Name Code: 43410
- Item Weight: 14.60 Pounds
- Item Dimensions: 30.1 x 7.5 x 6.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 43410-0W200
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2008 Toyota Highlander Submodels:
- Hybrid, Hybrid Limited | 6 Cyl 3.3 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.5 L FULL HYBRID EV-GAS (FHEV)
View related parts
2008 Toyota Highlander Axle Assembly, Driver Side
Part Number: 43420-0W220
$308.77 MSRP: $467.38
You Save: $158.61 (34%)
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Front Drive; CV Axle Assembly, Front Left; GSP Cv Axle; Axle Shaft; Shaft Assembly, Front Drive, Driver Side; CV Axle Assembly
- Position: Driver Side
- Part Name Code: 43420
- Item Weight: 14.50 Pounds
- Item Dimensions: 29.5 x 7.5 x 6.7 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 43420-0W220
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2008 Toyota Highlander Submodels:
- Base, Limited, SE, Sport | 6 Cyl 3.5 L GAS
View related parts
2008 Toyota Highlander Axle Assembly, Rear
Part Number: 42340-48081
$369.43 MSRP: $541.41
You Save: $171.98 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Rear Drive; CV Axle Assembly, Rear, Rear Left, Rear Right; GSP Cv Axle; Axle Shaft; Shaft Assembly, Rear Drive, Passenger Side; Shaft Assembly, Rear Drive, Driver Side; CV Axle Assembly
- Position: Rear
- Replaces: 42340-48080
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 42340-48081
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2008 Toyota Highlander Submodels:
- Hybrid, Hybrid Limited | 6 Cyl 3.3 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.5 L FULL HYBRID EV-GAS (FHEV)
View related parts
2008 Toyota Highlander Axle Assembly, Front Passenger Side
Part Number: 43410-0W240
$697.65 MSRP: $1048.95
You Save: $351.30 (34%)
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Front Drive; CV Axle Assembly, Front Right; CV Axle Assembly; GSP Cv Axle; Axle Shaft
- Position: Front Passenger Side
- Item Weight: 15.90 Pounds
- Item Dimensions: 44.1 x 6.5 x 5.3 inches
- Condition: New
- SKU: 43410-0W240
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2008 Toyota Highlander Submodels:
- Base, Limited, SE, Sport | 6 Cyl 3.5 L GAS
View related parts
2008 Toyota Highlander Outer CV Joint, Rear
Part Number: 42370-49245
$245.80 MSRP: $350.95
You Save: $105.15 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Rear Drive; CV Joint; Outer Joint; Rear Drive Outboard Joint, Passenger & Driver Side Shaft Assembly
- Position: Rear
- Item Weight: 14.10 Pounds
- Item Dimensions: 33.3 x 6.3 x 5.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 42370-49245
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2008 Toyota Highlander Submodels:
- Base, Limited, SE, Sport | 4 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS
View related parts
2008 Toyota Highlander Axle Assembly, Passenger Side
Part Number: 43410-0W210
$410.40 MSRP: $601.45
You Save: $191.05 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Front Drive; CV Axle Assembly, Front Right; GSP Cv Axle; Axle Shaft; Shaft Assembly, Front Drive, Passenger Side; CV Axle Assembly
- Position: Passenger Side
- Part Name Code: 43410
- Item Weight: 15.30 Pounds
- Item Dimensions: 29.5 x 7.3 x 6.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 43410-0W210
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2008 Toyota Highlander Submodels:
- Base, Limited, SE, Sport | 4 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS
View related parts
2008 Toyota Highlander Axle Shaft Assembly, Rear
Part Number: 42340-48070
$380.89 MSRP: $558.21
You Save: $177.32 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Rear Drive; CV Axle Assembly, Rear, Rear Left, Rear Right; GSP Cv Axle; Axle Shaft; Axle Assembly; Shaft Assembly, Rear Drive, Passenger Side; Shaft Assembly, Rear Drive, Driver Side; CV Axle Assembly
- Manufacturer Note: TYPE B:REFER ILLUST.
- Position: Rear
- Item Weight: 15.50 Pounds
- Item Dimensions: 28.4 x 8.5 x 7.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 42340-48070
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2008 Toyota Highlander Submodels:
- Base, Limited, Plus, SE, Sport | 4 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS
View related parts
2008 Toyota Highlander Axle Assembly, Driver Side
Part Number: 43420-0W240
$378.06 MSRP: $554.05
You Save: $175.99 (32%)
Product Specifications
- Other Name: Shaft Assembly, Front Drive; CV Axle Assembly, Front Left; GSP Cv Axle; Axle Shaft; Shaft Assembly, Front Drive, Driver Side; CV Axle Assembly
- Position: Driver Side
- Part Name Code: 43420
- Item Weight: 14.40 Pounds
- Item Dimensions: 29.5 x 7.4 x 6.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 43420-0W240
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2008 Toyota Highlander Submodels:
- Base, Limited, SE, Sport | 4 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS

2008 Toyota Highlander Axle Shaft

Looking for affordable OEM 2008 Toyota Highlander Axle Shaft? Explore our comprehensive catalogue of genuine 2008 Toyota Highlander Axle Shaft. All our parts are covered by the manufacturer's warranty. Plus, our straightforward return policy and speedy delivery service ensure an unparalleled shopping experience. We look forward to your visit!

2008 Toyota Highlander Axle Shaft Parts Q&A

Q: How to reassemble the axle shaft on 2008 Toyota Highlander?
A: The front drive shaft bearing assembly process for 2WD RH side starts with a new bearing bracket hole snap ring installation into the front drive shaft assembly RH followed by Special Service Tool: 09527-30010 09527-10011 usage to install a new front drive shaft bearing with complete insertion. The next step includes a new drive shaft hole snap ring installation by using a snap ring expander. A new drive shaft dust cover should be installed using Special Service Tool: 09726-40010 09527-10011 and a press until it achieves full installation without damage and the same procedure must be repeated for RH and LH dust covers at a distance of 109.0 to 110.0 mm on the RH cover. Repeat the installation procedure applied to the LH side for the 4WD RH side. The installation sequence for the front axle outboard joint boot consists of fitting the No. 2 front axle outboard joint boot clamp followed by the front axle outboard joint boot and finally the front axle outboard joint boot clamp in that order while applying grease to the joint. This procedure must be completed after wrapping the drive shaft splines with vinyl tape for protection. Before fastening the front axle outboard joint boot clamp to the drive shaft in a vise you need Special Service Tool: 09521-24010 to pinch it. Check the clearance which should be between 0.5 to 1.5 mm. Apply the same measurement steps to the No. 2 front axle outboard joint boot clamp. Place the drive shaft damper in the correct position before installing the drive shaft damper clamp while maintaining the same measurement technique for the clearance as before. The front drive inboard joint assembly requires vinyl tape on the splines followed by front axle inboard joint boot clamp then front axle inboard joint boot and lastly No. 2 front axle inboard joint boot clamp in sequence to achieve correct tripod joint installation without roller impacts while packing with grease. You should start by installing the front axle inboard joint boot and its clamps before checking the clearance value and placing the new front drive shaft hole snap ring.

Related 2008 Toyota Highlander Parts

Alternate Year Models

2007 Toyota Highlander Axle Shaft 2009 Toyota Highlander Axle Shaft