How to service and repair the rear Wheel Hub and Wheel Bearing on 2006 Toyota Highlander?

The initial step for rear wheel hub and bearing servicing involves using a dial indicator to check for hub looseness at its center point with a measurement surface set at right angles while maximum acceptable looseness stands at 0 mm (0 inch) with an extreme value requiring a wheel hub assembly replacement. The measurement of external hub bolt surface runout must not exceed 0.08 mm (0.0031 inch); when this limit is surpassed the wheel hub assembly needs replacement. Remove the front wheel before starting to disassemble the right-hand side rear disc brake caliper assembly by disconnecting its flexible hose and securing bolt followed by the two brake caliper securing bolts and maintaining the caliper securely. After disc removal disconnect the skid control sensor wire. Next detach the rear wheel hub and bearing assembly through removal of the four bolts from the left-hand side. First install the left-hand side rear wheel hub by connecting it with four bolts which demand torque specification at 80 Nm (816 kgf-cm, 59 ft. lbs.). The skid control sensor wire restarts first before you inspect bearing backlash and axial hub deviation to proceed with rear disc installation. Put the two bolts into position around the right-hand side rear disk brake caliper assembly and torque them to 78 Nm (800 kgf-cm, 58 ft. lbs.). Secure the flexible hose with the bolt torqued to 19 Nm (194 kgf-cm, 14 ft. lbs.). To finish the installation you should torque the rear wheel to 103 Nm (1,050 kgf-cm, 76 ft. lbs.) before inspecting wheel alignment and checking the ABS speed sensor signal.

OEM 2006 Toyota Highlander Wheel Bearing

Hub Bearing

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

7 Wheel Bearings found

View related parts
2006 Toyota Highlander Hub Assembly, Front
Part Number: 43502-0E030
$130.65 MSRP: $184.95
You Save: $54.30 (30%)
ADD TO CART
Product Specifications
- Other Name: Hub Sub-Assembly, Front Axle; Wheel Hub, Front; Front Hub & Bearing; Front Hub; Hub
- Position: Front
- Replaces: 43502-AA021, 43502-28100, 43502-08010, 43502-AA020
- Item Weight: 5.10 Pounds
- Item Dimensions: 6.6 x 6.9 x 4.6 inches
- Condition: New
- SKU: 43502-0E030
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2006 Toyota Highlander Submodels:
- Base, Hybrid, Hybrid Limited, Limited, SE, Sport | 4 Cyl 2.7 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.3 L GAS, 6 Cyl 3.5 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.5 L GAS
View related parts
2006 Toyota Highlander Wheel Bearing
Part Number: 90080-36193
$102.30 MSRP: $143.60
You Save: $41.30 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Radial Ball; Wheel Bearing, Front, Front Left, Front Right; Wheel Bearing Kit; Front Wheel Bearing for Passenger and Driver Side Axle Hub.
- Replaces: 90363-A0001, 90369-45005, 90369-45003
- Item Weight: 2.40 Pounds
- Item Dimensions: 3.7 x 3.7 x 2.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 90080-36193
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2006 Toyota Highlander Submodels:
- Base, Hybrid, Hybrid Limited, Limited, Sport | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.3 L GAS
View related parts
2006 Toyota Highlander Hub & Bearing Assembly, Rear Axle, Passenger Side
Part Number: 42410-0E050
$323.57 MSRP: $461.97
You Save: $138.40 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub&Bearing Assembly; Rear Axle, Driver Side; Wheel Hub Repair Kit; Wheel Bearing Kit; Axle Bearing
- Replaces: 42410-48041, 42410-0E021, 42410-48040
- Item Weight: 8.30 Pounds
- Item Dimensions: 6.9 x 6.9 x 4.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 42410-0E050
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2006 Toyota Highlander Submodels:
- Base, Hybrid, Hybrid Limited, Limited, Plus, SE, Sport | 4 Cyl 2.4 L GAS, 4 Cyl 2.7 L GAS, 6 Cyl 3.3 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.3 L GAS, 6 Cyl 3.5 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.5 L GAS
View related parts
2006 Toyota Highlander Bearing (For Front Drive Shaft)
Part Number: 90080-36133
$31.18 MSRP: $43.39
You Save: $12.21 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Radial Ball; Wheel Bearing; Axle Bearing
- Replaces: 90363-41002, 90369-41001
- Part Name Code: 43410C
- Item Weight: 1.10 Pounds
- Item Dimensions: 3.2 x 1.0 x 3.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 90080-36133
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2006 Toyota Highlander Submodels:
- Base, Hybrid, Hybrid LE, Hybrid Limited, Hybrid Limited Platinum, Hybrid XLE, LE, LE Plus, Limited, Limited Platinum, Plus, SE, Sport, XLE | 4 Cyl 2.7 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.3 L GAS, 6 Cyl 3.5 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.5 L GAS
View related parts
2006 Toyota Highlander Hub Assembly, Front
Part Number: 43502-28090
$129.36 MSRP: $183.12
You Save: $53.76 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub Sub-Assembly, Front Axle; Wheel Hub, Front; Front Hub; Hub; Hub Sub-Assembly, Front Axle, Passenger Side; Hub Sub-Assembly, Front Axle, Driver Side; Wheel Hub
- Manufacturer Note: (J)
- Position: Front
- Replaces: 43502-AA010, 43502-AA011
- Item Weight: 4.10 Pounds
- Item Dimensions: 6.7 x 6.7 x 4.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 43502-28090
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2006 Toyota Highlander Submodels:
- Base, Limited, SE, Sport | 4 Cyl 2.4 L GAS, 4 Cyl 2.7 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L GAS, 6 Cyl 3.5 L GAS
View related parts
2006 Toyota Highlander Hub&Bearing Assembly, Rear Axle
Part Number: 42460-0E010
$507.55 MSRP: $743.82
You Save: $236.27 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: HUB & BRG ASSY, RR A; Wheel Bearing and Hub Assembly; Wheel Hub Repair Kit; Wheel Bearing; Axle Bearing; Wheel Hub
- Position: Rear Driver Side
- Replaces: 42460-48030
- Item Weight: 9.90 Pounds
- Item Dimensions: 7.1 x 6.8 x 5.3 inches
- Condition: New
- SKU: 42460-0E010
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2006 Toyota Highlander Submodels:
- Base, Hybrid, Hybrid Limited, Limited, Sport | 4 Cyl 2.4 L GAS, 6 Cyl 3.3 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.3 L GAS
View related parts
2006 Toyota Highlander Hub&Bearing Assembly, Rear Axle
Part Number: 42450-0E010
$507.55 MSRP: $743.82
You Save: $236.27 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: HUB & BRG ASSY, RR A; Wheel Bearing and Hub Assembly; Wheel Hub Repair Kit; Wheel Bearing; Axle Bearing; Wheel Hub
- Position: Rear Passenger Side
- Replaces: 42450-48030
- Item Weight: 10.00 Pounds
- Item Dimensions: 7.0 x 6.5 x 5.1 inches
- Condition: New
- SKU: 42450-0E010
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2006 Toyota Highlander Submodels:
- Base, Hybrid, Hybrid Limited, Limited, Sport | 4 Cyl 2.4 L GAS, 6 Cyl 3.3 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.3 L GAS

2006 Toyota Highlander Wheel Bearing

Looking for affordable OEM 2006 Toyota Highlander Wheel Bearing? Explore our comprehensive catalogue of genuine 2006 Toyota Highlander Wheel Bearing. All our parts are covered by the manufacturer's warranty. Plus, our straightforward return policy and speedy delivery service ensure an unparalleled shopping experience. We look forward to your visit!

2006 Toyota Highlander Parts Questions & Experts Answers

Q: How to service and repair the rear Wheel Hub and Wheel Bearing on 2006 Toyota Highlander?
A: The initial step for rear wheel hub and bearing servicing involves using a dial indicator to check for hub looseness at its center point with a measurement surface set at right angles while maximum acceptable looseness stands at 0 mm (0 inch) with an extreme value requiring a wheel hub assembly replacement. The measurement of external hub bolt surface runout must not exceed 0.08 mm (0.0031 inch); when this limit is surpassed the wheel hub assembly needs replacement. Remove the front wheel before starting to disassemble the right-hand side rear disc brake caliper assembly by disconnecting its flexible hose and securing bolt followed by the two brake caliper securing bolts and maintaining the caliper securely. After disc removal disconnect the skid control sensor wire. Next detach the rear wheel hub and bearing assembly through removal of the four bolts from the left-hand side. First install the left-hand side rear wheel hub by connecting it with four bolts which demand torque specification at 80 Nm (816 kgf-cm, 59 ft. lbs.). The skid control sensor wire restarts first before you inspect bearing backlash and axial hub deviation to proceed with rear disc installation. Put the two bolts into position around the right-hand side rear disk brake caliper assembly and torque them to 78 Nm (800 kgf-cm, 58 ft. lbs.). Secure the flexible hose with the bolt torqued to 19 Nm (194 kgf-cm, 14 ft. lbs.). To finish the installation you should torque the rear wheel to 103 Nm (1,050 kgf-cm, 76 ft. lbs.) before inspecting wheel alignment and checking the ABS speed sensor signal.