How to replace the rear wheel bearing on 2005 Toyota Highlander?

Start with removing the rear wheel before beginning the replacement of the rear wheel bearing. Start by taking apart the rear disc brake caliper assembly on the left-hand side through bolt removal of the flexible hose followed by two bolts used to hold the brake caliper then use a support to keep the caliper in place. The speed sensor wire needs its connector unplugged before removing the rear disc part. Begin to uninstall the left-hand side rear axle hub assembly through the removal of four bolts. Install the new axle hub by using its four bolts then tighten them up to 80 Nm (816 kgf-cm, 59 ft. lbs.). The speed sensor wire requires connection by inserting its connector back into place. Check backlash of the bearing using a dial indicator at the axle hub center point where the maximum allowable amount is 0.0 mm (0.0 inch) but any higher amount indicates that the axle hub assembly needs replacement. At the surface of the axle hub outside the hub bolt the deviation measurement should be checked with a dial indicator for a maximum allowable limit of 0.08 mm (0.0031 inch) and the axle hub assembly needs to be replaced if this limit is exceeded. Start by attaching the back disc followed by the rear disc brake caliper assembly to the left-hand side using the two bolts tightened up to 78 Nm (800 kgf-cm, 58 ft. lbs.). Reattach the flexible hose through its bolt with a torque of 19 Nm (194 kgf-cm, 14 ft. lbs.). The last step includes reinstalling the rear wheel while torquing it to 103 Nm (1,050 kgf-cm, 76 ft. lbs.) followed by examinations of rear wheel alignment and ABS speed sensor signal checks.

OEM 2005 Toyota Highlander Wheel Bearing

Hub Bearing

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

7 Wheel Bearings found

View related parts
2005 Toyota Highlander Hub Assembly, Front
Part Number: 43502-0E030
$130.65 MSRP: $184.95
You Save: $54.30 (30%)
ADD TO CART
Product Specifications
- Other Name: Hub Sub-Assembly, Front Axle; Wheel Hub, Front; Front Hub & Bearing; Front Hub; Hub
- Position: Front
- Replaces: 43502-AA021, 43502-28100, 43502-08010, 43502-AA020
- Item Weight: 5.10 Pounds
- Item Dimensions: 6.6 x 6.9 x 4.6 inches
- Condition: New
- SKU: 43502-0E030
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2005 Toyota Highlander Submodels:
- Base, Hybrid, Hybrid Limited, Limited, SE, Sport | 4 Cyl 2.7 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.3 L GAS, 6 Cyl 3.5 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.5 L GAS
View related parts
2005 Toyota Highlander Wheel Bearing
Part Number: 90080-36193
$102.30 MSRP: $143.60
You Save: $41.30 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Radial Ball; Wheel Bearing, Front, Front Left, Front Right; Wheel Bearing Kit; Front Wheel Bearing for Passenger and Driver Side Axle Hub.
- Replaces: 90363-A0001, 90369-45005, 90369-45003
- Item Weight: 2.40 Pounds
- Item Dimensions: 3.7 x 3.7 x 2.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 90080-36193
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2005 Toyota Highlander Submodels:
- Base, Hybrid, Hybrid Limited, Limited, Sport | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.3 L GAS
View related parts
2005 Toyota Highlander Hub & Bearing Assembly, Rear Axle, Passenger Side
Part Number: 42410-0E050
$323.57 MSRP: $461.97
You Save: $138.40 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub&Bearing Assembly; Rear Axle, Driver Side; Wheel Hub Repair Kit; Wheel Bearing Kit; Axle Bearing
- Replaces: 42410-48041, 42410-0E021, 42410-48040
- Item Weight: 8.30 Pounds
- Item Dimensions: 6.9 x 6.9 x 4.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 42410-0E050
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2005 Toyota Highlander Submodels:
- Base, Hybrid, Hybrid Limited, Limited, Plus, SE, Sport | 4 Cyl 2.4 L GAS, 4 Cyl 2.7 L GAS, 6 Cyl 3.3 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.3 L GAS, 6 Cyl 3.5 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.5 L GAS
View related parts
2005 Toyota Highlander Bearing (For Front Drive Shaft)
Part Number: 90080-36133
$31.18 MSRP: $43.39
You Save: $12.21 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Radial Ball; Wheel Bearing; Axle Bearing
- Replaces: 90363-41002, 90369-41001
- Part Name Code: 43410C
- Item Weight: 1.10 Pounds
- Item Dimensions: 3.2 x 1.0 x 3.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 90080-36133
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2005 Toyota Highlander Submodels:
- Base, Hybrid, Hybrid LE, Hybrid Limited, Hybrid Limited Platinum, Hybrid XLE, LE, LE Plus, Limited, Limited Platinum, Plus, SE, Sport, XLE | 4 Cyl 2.7 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.3 L GAS, 6 Cyl 3.5 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.5 L GAS
View related parts
2005 Toyota Highlander Hub Assembly, Front
Part Number: 43502-28090
$129.36 MSRP: $183.12
You Save: $53.76 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub Sub-Assembly, Front Axle; Wheel Hub, Front; Front Hub; Hub; Hub Sub-Assembly, Front Axle, Passenger Side; Hub Sub-Assembly, Front Axle, Driver Side; Wheel Hub
- Manufacturer Note: (J)
- Position: Front
- Replaces: 43502-AA010, 43502-AA011
- Item Weight: 4.10 Pounds
- Item Dimensions: 6.7 x 6.7 x 4.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 43502-28090
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2005 Toyota Highlander Submodels:
- Base, Limited, SE, Sport | 4 Cyl 2.4 L GAS, 4 Cyl 2.7 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L GAS, 6 Cyl 3.5 L GAS
View related parts
2005 Toyota Highlander Hub&Bearing Assembly, Rear Axle
Part Number: 42460-0E010
$507.55 MSRP: $743.82
You Save: $236.27 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: HUB & BRG ASSY, RR A; Wheel Bearing and Hub Assembly; Wheel Hub Repair Kit; Wheel Bearing; Axle Bearing; Wheel Hub
- Position: Rear Driver Side
- Replaces: 42460-48030
- Item Weight: 9.90 Pounds
- Item Dimensions: 7.1 x 6.8 x 5.3 inches
- Condition: New
- SKU: 42460-0E010
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2005 Toyota Highlander Submodels:
- Base, Hybrid, Hybrid Limited, Limited, Sport | 4 Cyl 2.4 L GAS, 6 Cyl 3.3 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.3 L GAS
View related parts
2005 Toyota Highlander Hub&Bearing Assembly, Rear Axle
Part Number: 42450-0E010
$507.55 MSRP: $743.82
You Save: $236.27 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: HUB & BRG ASSY, RR A; Wheel Bearing and Hub Assembly; Wheel Hub Repair Kit; Wheel Bearing; Axle Bearing; Wheel Hub
- Position: Rear Passenger Side
- Replaces: 42450-48030
- Item Weight: 10.00 Pounds
- Item Dimensions: 7.0 x 6.5 x 5.1 inches
- Condition: New
- SKU: 42450-0E010
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2005 Toyota Highlander Submodels:
- Base, Hybrid, Hybrid Limited, Limited, Sport | 4 Cyl 2.4 L GAS, 6 Cyl 3.3 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.3 L GAS

2005 Toyota Highlander Wheel Bearing

Looking for affordable OEM 2005 Toyota Highlander Wheel Bearing? Explore our comprehensive catalogue of genuine 2005 Toyota Highlander Wheel Bearing. All our parts are covered by the manufacturer's warranty. Plus, our straightforward return policy and speedy delivery service ensure an unparalleled shopping experience. We look forward to your visit!

2005 Toyota Highlander Parts Questions & Experts Answers

Q: How to replace the rear wheel bearing on 2005 Toyota Highlander?
A: Start with removing the rear wheel before beginning the replacement of the rear wheel bearing. Start by taking apart the rear disc brake caliper assembly on the left-hand side through bolt removal of the flexible hose followed by two bolts used to hold the brake caliper then use a support to keep the caliper in place. The speed sensor wire needs its connector unplugged before removing the rear disc part. Begin to uninstall the left-hand side rear axle hub assembly through the removal of four bolts. Install the new axle hub by using its four bolts then tighten them up to 80 Nm (816 kgf-cm, 59 ft. lbs.). The speed sensor wire requires connection by inserting its connector back into place. Check backlash of the bearing using a dial indicator at the axle hub center point where the maximum allowable amount is 0.0 mm (0.0 inch) but any higher amount indicates that the axle hub assembly needs replacement. At the surface of the axle hub outside the hub bolt the deviation measurement should be checked with a dial indicator for a maximum allowable limit of 0.08 mm (0.0031 inch) and the axle hub assembly needs to be replaced if this limit is exceeded. Start by attaching the back disc followed by the rear disc brake caliper assembly to the left-hand side using the two bolts tightened up to 78 Nm (800 kgf-cm, 58 ft. lbs.). Reattach the flexible hose through its bolt with a torque of 19 Nm (194 kgf-cm, 14 ft. lbs.). The last step includes reinstalling the rear wheel while torquing it to 103 Nm (1,050 kgf-cm, 76 ft. lbs.) followed by examinations of rear wheel alignment and ABS speed sensor signal checks.