How to replace the rear wheel bearing on 2001 Toyota Highlander?

The replacement of the rear wheel bearing begins with disc caliper brake assembly detachment including a bolt removal to separate the flexible hose and subsequent removal of two brake caliper retaining bolts. The first task requires disconnecting the flexible hose by unbolting the bolt and removing both brake caliper bolts on the left side wheel while maintaining proper support of the brake caliper assembly. Reduce the rear disc [42431 / 98-63] and separate the skid control sensor wire [89516 / 98-170] by disconnecting the connector. You must remove the left side rear axle hub and bearing assembly [42450B / 98-63] by extracting its four bolts and subsequent removal of the axle hub. First remove the existing skid control sensor [89544 / 98-170] before adding a new sensor of the same model [89544 / 98-170]. Secure the left side rear axle hub and bearing assembly [42450B / 98-63] with four bolts which should be torqued to 80 Nm (816 kgf-cm, 59 ft. lbs.). Resume the skid control sensor wire operation by attaching its connector [89516 / 98-170]. The bearing backlash inspection requires a dial indicator near the center of the axle hub which must not exceed 0.05 mm (0.0020 inch) maximum; when the value surpasses this threshold a new axle hub assembly must be installed. A dial indicator should check the axle hub deviation at the surface outside the hub bolt, and replacement of the axle hub assembly is necessary when the measurement exceeds 0.07 mm (0.0028 inch). Place the rear disc [42431 / 98-63] before setting the rear disc brake caliper assembly to the left side and tighten both bolts to 61.8 Nm (630 kgf-cm, 46 ft. lbs.) before securing the flexible hose with a bolt torqued to 29.4Nm (300 kgf-cm, 22 ft. lbs.). After reinstalling the rear wheel users should torque it to 103 Nm (1,050 kgf-cm, 76 ft. lbs.). Then they should perform wheel alignment checks followed by ABS speed sensor signal assessment.

OEM 2001 Toyota Highlander Wheel Bearing

Hub Bearing

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

8 Wheel Bearings found

View related parts
2001 Toyota Highlander Bearing (For Front Drive Shaft)
Part Number: 90080-36133
$31.18 MSRP: $43.39
You Save: $12.21 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Radial Ball; Wheel Bearing; Axle Bearing
- Replaces: 90363-41002, 90369-41001
- Part Name Code: 43410C
- Item Weight: 1.10 Pounds
- Item Dimensions: 3.2 x 1.0 x 3.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 90080-36133
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2001 Toyota Highlander Submodels:
- Base, Hybrid, Hybrid LE, Hybrid Limited, Hybrid Limited Platinum, Hybrid XLE, LE, LE Plus, Limited, Limited Platinum, Plus, SE, Sport, XLE | 4 Cyl 2.7 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.3 L GAS, 6 Cyl 3.5 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.5 L GAS
View related parts
2001 Toyota Highlander Hub Assembly, Front
Part Number: 43502-0E030
$130.65 MSRP: $184.95
You Save: $54.30 (30%)
ADD TO CART
Product Specifications
- Other Name: Hub Sub-Assembly, Front Axle; Wheel Hub, Front; Front Hub & Bearing; Front Hub; Hub
- Position: Front
- Replaces: 43502-AA021, 43502-28100, 43502-08010, 43502-AA020
- Item Weight: 5.10 Pounds
- Item Dimensions: 6.6 x 6.9 x 4.6 inches
- Condition: New
- SKU: 43502-0E030
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2001 Toyota Highlander Submodels:
- Base, Hybrid, Hybrid Limited, Limited, SE, Sport | 4 Cyl 2.7 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.3 L GAS, 6 Cyl 3.5 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.5 L GAS
View related parts
2001 Toyota Highlander Wheel Bearing
Part Number: 90080-36193
$102.37 MSRP: $143.70
You Save: $41.33 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Radial Ball; Wheel Bearing, Front, Front Left, Front Right; Wheel Bearing Kit; Front Wheel Bearing for Passenger and Driver Side Axle Hub.
- Replaces: 90363-A0001, 90369-45005, 90369-45003
- Item Weight: 2.40 Pounds
- Item Dimensions: 3.7 x 3.7 x 2.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 90080-36193
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2001 Toyota Highlander Submodels:
- Base, Hybrid, Hybrid Limited, Limited, Sport | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.3 L GAS
View related parts
2001 Toyota Highlander Hub & Bearing Assembly, Rear Axle, Driver Side
Part Number: 42460-48011
$478.62 MSRP: $701.43
You Save: $222.81 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub&Bearing Assembly, Rear Axle; Wheel Hub Repair Kit; Bearing; Axle Bearing
- Position: Driver Side
- Replaces: 42460-06021, 42460-06020, 42460-48010, 42460-06030
- Part Name Code: 42450B
- Item Weight: 8.50 Pounds
- Item Dimensions: 7.0 x 6.8 x 7.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 42460-48011
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2001 Toyota Highlander Submodels:
- Base, Limited | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS
View related parts
2001 Toyota Highlander Hub Assembly, Front
Part Number: 43502-28090
$129.36 MSRP: $183.12
You Save: $53.76 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub Sub-Assembly, Front Axle; Wheel Hub, Front; Front Hub; Hub; Hub Sub-Assembly, Front Axle, Passenger Side; Hub Sub-Assembly, Front Axle, Driver Side; Wheel Hub
- Manufacturer Note: (J)
- Position: Front
- Replaces: 43502-AA010, 43502-AA011
- Item Weight: 4.10 Pounds
- Item Dimensions: 6.7 x 6.7 x 4.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 43502-28090
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2001 Toyota Highlander Submodels:
- Base, Limited, SE, Sport | 4 Cyl 2.4 L GAS, 4 Cyl 2.7 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L GAS, 6 Cyl 3.5 L GAS
View related parts
2001 Toyota Highlander Hub Assembly, Passenger Side
Part Number: 42450-48011
$515.62 MSRP: $755.65
You Save: $240.03 (32%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Hub&Bearing Assembly, Rear Axle; Rear Right Wheel Bearing & Hub; Wheel Hub Repair Kit; Axle Bearing; Hub & Bearing Assembly, Rear Axle, Passenger Side; Wheel Bearing and Hub Assembly
- Position: Passenger Side
- Replaces: 42450-06030, 42450-48010, 42450-06020, 42450-06021, 42450-48020
- Part Name Code: 42450A
- Item Weight: 9.10 Pounds
- Item Dimensions: 6.8 x 6.9 x 7.7 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 42450-48011
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2001 Toyota Highlander Submodels:
- Base, Limited | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS
View related parts
2001 Toyota Highlander Bearing(For Rear Axle Shaft Passenger Side)
Part Number: 90369-38019
$157.32 MSRP: $222.71
You Save: $65.39 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing; Bearing(For Rear Axle Shaft Driver Side); Wheel Bearing; Axle Bearing
- Item Weight: 1.80 Pounds
- Item Dimensions: 3.7 x 3.6 x 2.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 90369-38019
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2001 Toyota Highlander Submodels:
- Base, Limited | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS
View related parts
2001 Toyota Highlander Front Hub Bearing
Part Number: 90369-45004
$76.54 MSRP: $107.44
You Save: $30.90 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing; Wheel Bearing, Front; Wheel Hub Repair Kit; Axle Bearing; Wheel Hub; Bearing (For Front Axle Hub Passenger Side); Bearing (For Front Axle Hub Driver Side); Wheel Bearing
- Manufacturer Note: NACHI
- Item Weight: 2.30 Pounds
- Item Dimensions: 3.5 x 3.7 x 2.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 90369-45004
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2001 Toyota Highlander Submodels:
- Base, Limited | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS

2001 Toyota Highlander Wheel Bearing

Looking for affordable OEM 2001 Toyota Highlander Wheel Bearing? Explore our comprehensive catalogue of genuine 2001 Toyota Highlander Wheel Bearing. All our parts are covered by the manufacturer's warranty. Plus, our straightforward return policy and speedy delivery service ensure an unparalleled shopping experience. We look forward to your visit!

2001 Toyota Highlander Wheel Bearing Parts Q&A

Q: How to replace the rear wheel bearing on 2001 Toyota Highlander?
A: The replacement of the rear wheel bearing begins with disc caliper brake assembly detachment including a bolt removal to separate the flexible hose and subsequent removal of two brake caliper retaining bolts. The first task requires disconnecting the flexible hose by unbolting the bolt and removing both brake caliper bolts on the left side wheel while maintaining proper support of the brake caliper assembly. Reduce the rear disc [42431 / 98-63] and separate the skid control sensor wire [89516 / 98-170] by disconnecting the connector. You must remove the left side rear axle hub and bearing assembly [42450B / 98-63] by extracting its four bolts and subsequent removal of the axle hub. First remove the existing skid control sensor [89544 / 98-170] before adding a new sensor of the same model [89544 / 98-170]. Secure the left side rear axle hub and bearing assembly [42450B / 98-63] with four bolts which should be torqued to 80 Nm (816 kgf-cm, 59 ft. lbs.). Resume the skid control sensor wire operation by attaching its connector [89516 / 98-170]. The bearing backlash inspection requires a dial indicator near the center of the axle hub which must not exceed 0.05 mm (0.0020 inch) maximum; when the value surpasses this threshold a new axle hub assembly must be installed. A dial indicator should check the axle hub deviation at the surface outside the hub bolt, and replacement of the axle hub assembly is necessary when the measurement exceeds 0.07 mm (0.0028 inch). Place the rear disc [42431 / 98-63] before setting the rear disc brake caliper assembly to the left side and tighten both bolts to 61.8 Nm (630 kgf-cm, 46 ft. lbs.) before securing the flexible hose with a bolt torqued to 29.4Nm (300 kgf-cm, 22 ft. lbs.). After reinstalling the rear wheel users should torque it to 103 Nm (1,050 kgf-cm, 76 ft. lbs.). Then they should perform wheel alignment checks followed by ABS speed sensor signal assessment.

Alternate Year Models

2002 Toyota Highlander Wheel Bearing