How to install the hood cable assembly and related components on Scion xD?

Follow these steps to install the hood cable assembly by passing it through the engine compartment until all clamps match the given illustrations. You must first install the hood lock control lever sub-assembly while connecting its hood cable. Use MP grease for hood lock sliding areas while attaching the hood cable before installing the three bolts that should be torqued at 7.5 Nm (76 kgf-cm, 66 in-lbf). An inspection and necessary adjustment operations must be performed to the hood sub-assembly. Use three new grommets with eight clips together with six screws to install the front fender liner LH maintaining proper alignment for the pin hold clip slot being straight up and down without clockwise or counterclockwise rotation. Conclude the installation process by adding the side mudguard then the rocker panel molding cover before featuring the front wheel.

How to remove the Hood Cable Assembly on Scion xB?

The first step for removing the Hood Lock Control Cable Assembly requires wheel removal followed by disassembly of the LH front wheel opening extension pad through screw removal. Once the front side mudguard falls away the technician must pull out two screws and grommets to finish the removal. Proceed to the front fender liner LH by rotating 90 degrees with a screwdriver the pin hold clip then take off eight clips followed by four screws and finally remove three grommets. You need to purchase a fresh grommet because the existing one will break during the process of removal. The next step involves removing the radiator cover through the process of unscrewing its 5 clips. The water hose clamp bracket needs removal when both bolts are unscrewed. Before continuing proceed to remove the hood lock assembly which requires detachment of the hood cable followed by unscrewing its three bolts. Detach the hood cable for a second time after which you should remove the hood lock control lever. The removal process finishes with a screwdriver that has tape coverage on its tip to disconnect clamps before pulling the cable out of the engine compartment.

OEM Scion Hood Cable

Hood Release Cable

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

13 Hood Cables found

View related parts
Scion Release Cable, Front
Part Number: 53630-52110
$37.87 MSRP: $52.72
You Save: $14.85 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assembly, Hood Lock; Hood Release Cable, Front; Cable Assembly, Hood Lock Control; Hood Release Cable
- Position: Front
Fits the following Scion Models:
- xD | 2008-2014 | Base | 4 Cyl 1.8 L GAS
View related parts
Scion Release Cable, Front
Part Number: 53630-52090
$42.65 MSRP: $59.36
You Save: $16.71 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assembly, Hood Lock; Hood Release Cable, Front; Cable Assembly, Hood Lock Control; Hood Release Cable
- Position: Front
Fits the following Scion Models:
- xB | 2004-2006 | Base | 4 Cyl 1.5 L GAS
View related parts
Scion Release Cable, Front
Part Number: 53630-21020
$37.87 MSRP: $52.72
You Save: $14.85 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assembly, Hood Lock; Hood Release Cable, Front; Cable Assembly, Hood Lock Control; Hood Release Cable
- Position: Front
Fits the following Scion Models:
- tC | 2011-2016 | Base | 4 Cyl 2.5 L GAS
View related parts
Scion Release Cable, Front
Part Number: 53630-21010
$42.65 MSRP: $59.36
You Save: $16.71 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assembly, Hood Lock; Hood Release Cable, Front; Cable Assembly, Hood Lock Control; Hood Release Cable
- Position: Front
Fits the following Scion Models:
- tC | 2005-2010 | Base, Spec | 4 Cyl 2.4 L GAS
View related parts
Scion Release Cable, Front
Part Number: 53630-12640
$35.48 MSRP: $49.39
You Save: $13.91 (29%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Cable Assembly, Hood Lock; Hood Release Cable, Front; Cable Assembly, Hood Lock Control; Hood Release Cable
- Position: Front
Fits the following Scion Models:
- xB | 2008-2015 | Base | 4 Cyl 2.4 L GAS
View related parts
Scion Release Handle, Front
Part Number: 53601-52010-B3
$45.64 MSRP: $63.52
You Save: $17.88 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Lever Sub-Assembly, Hood; Hood Release Handle, Front; Lever Sub-Assembly, Hood Lock Control
- Position: Front
Fits the following Scion Models:
- tC | 2011-2016 | Base | 4 Cyl 2.5 L GAS
- xB | 2011-2015 | Base | 4 Cyl 2.4 L GAS
View related parts
Scion Release Handle, Dark Gray, Front
Part Number: 53601-02020-B1
$46.47 MSRP: $64.68
You Save: $18.21 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Lever Sub-Assembly, Hood; Hood Release Handle, Front; Lever; Lever Sub-Assembly, Hood Lock Control
- Position: Front
Fits the following Scion Models:
- tC | 2005-2010 | Base, Spec | 4 Cyl 2.4 L GAS
- xA | 2004-2006 | Base | 4 Cyl 1.5 L GAS
- xB | 2008-2010, 2004-2006 | Base | 4 Cyl 1.5 L GAS, 4 Cyl 2.4 L GAS
- xD | 2008-2012 | Base | 4 Cyl 1.8 L GAS
View More
View related parts
Scion Release Handle, Front Driver Side
Part Number: SU003-01410
$12.32 MSRP: $15.95
You Save: $3.63 (23%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pull Handle Assembly Head Left-Hand; Hood Release Handle, Front; Lever Sub-Assembly, Hood Lock Control
- Position: Front Driver Side
Fits the following Scion Models:
- FR-S | 2013-2016 | Base | 4 Cyl 2.0 L GAS
View related parts
Scion Release Cable, Front
Part Number: SU003-01403
$19.31 MSRP: $25.00
You Save: $5.69 (23%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assembly Front Hood; Hood Release Cable, Front; Cable Assembly, Hood Lock Control; Hood Release Cable
- Position: Front
Fits the following Scion Models:
- FR-S | 2013-2016 | Base | 4 Cyl 2.0 L GAS
View related parts
Scion Release Cable, Front
Part Number: 53630-74010
$37.87 MSRP: $52.72
You Save: $14.85 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assembly, Hood Lock; Hood Release Cable, Front; Cable Assembly, Hood Lock Control; Hood Release Cable
- Position: Front
Fits the following Scion Models:
- iQ | 2012-2015 | Base | 4 Cyl 1.3 L GAS
View related parts
Scion Release Cable, Front
Part Number: 53630-52051
$42.65 MSRP: $59.36
You Save: $16.71 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assembly, Hood Lock; Hood Release Cable, Front; Cable Assembly, Hood Lock Control; Hood Release Cable
- Position: Front
- Replaces: 53630-52050
Fits the following Scion Models:
- xA | 2004-2006 | Base | 4 Cyl 1.5 L GAS
View related parts
Scion Release Cable, Front
Part Number: 53630-12740
$34.28 MSRP: $47.72
You Save: $13.44 (29%)
ADD TO CART
Product Specifications
- Other Name: Cable Assembly, Hood Lock; Hood Release Cable, Front; Cable Assembly, Hood Lock Control; Hood Release Cable
- Position: Front
Fits the following Scion Models:
- iM | 2016 | Base | 4 Cyl 1.8 L GAS
View related parts
Scion Release Cable, Front
Part Number: 53600-WB002
$30.10 MSRP: $41.90
You Save: $11.80 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Lever & Cable Assembly; Hood Release Cable, Front; Lever Assembly, Hood Lock Release; Hood Release Cable
- Position: Front
- Replaces: 53600-WB001
Fits the following Scion Models:
- iA | 2016 | Base | 4 Cyl 1.5 L GAS

Scion Hood Cable

OEM parts deliver unmatched quality you can rely on. They pass extensive quality control inspections. Scion produces them to the official factory specifications. This process helps prevent defects and imperfections. So you can get exceptional lifespan and a flawless fit. Need new OEM Scion Hood Cable? You'll love our wide selection of genuine options. Shop in minutes and skip the hunt. Our prices are unbeatable, you'll save time and money. It's easy to shop and find the right piece. Our committed customer service team gives professional help from start to finish. Every part includes a manufacturer's warranty. We ship quickly, your parts will arrive fast at your door.

Scion Hood Cable Parts and Q&A

Release Cable, Front
53630-52110
Q: How to install the hood cable assembly and related components on Scion xD?
A:
Follow these steps to install the hood cable assembly by passing it through the engine compartment until all clamps match the given illustrations. You must first install the hood lock control lever sub-assembly while connecting its hood cable. Use MP grease for hood lock sliding areas while attaching the hood cable before installing the three bolts that should be torqued at 7.5 Nm (76 kgf-cm, 66 in-lbf). An inspection and necessary adjustment operations must be performed to the hood sub-assembly. Use three new grommets with eight clips together with six screws to install the front fender liner LH maintaining proper alignment for the pin hold clip slot being straight up and down without clockwise or counterclockwise rotation. Conclude the installation process by adding the side mudguard then the rocker panel molding cover before featuring the front wheel.
Release Cable, Front
53630-12640
Q: How to remove the Hood Cable Assembly on Scion xB?
A:
The first step for removing the Hood Lock Control Cable Assembly requires wheel removal followed by disassembly of the LH front wheel opening extension pad through screw removal. Once the front side mudguard falls away the technician must pull out two screws and grommets to finish the removal. Proceed to the front fender liner LH by rotating 90 degrees with a screwdriver the pin hold clip then take off eight clips followed by four screws and finally remove three grommets. You need to purchase a fresh grommet because the existing one will break during the process of removal. The next step involves removing the radiator cover through the process of unscrewing its 5 clips. The water hose clamp bracket needs removal when both bolts are unscrewed. Before continuing proceed to remove the hood lock assembly which requires detachment of the hood cable followed by unscrewing its three bolts. Detach the hood cable for a second time after which you should remove the hood lock control lever. The removal process finishes with a screwdriver that has tape coverage on its tip to disconnect clamps before pulling the cable out of the engine compartment.

Related Scion Parts

Browse Scion Hood Cable by Models

tC xB iQ xA xD FR-S iA iM