How to install the heated oxygen sensor for Bank 2 Sensor 2 on 2009 Toyota Sienna?

Special Service Tool: 09224-00010 must be used to connect the Bank 2 Sensor 2 heated oxygen sensor to the front exhaust pipe with 40 Nm (408 kgf-cm, 30ft-lbf) torque using the tool while 44 Nm (449 kgf-cm, 32ft-lbf) torque can be achieved without the tool. It requires the use of a torque wrench with a 30 cm (11.81 in.) fullcrum and straight alignment of the tool and wrench. Start by putting two new gaskets onto the front exhaust pipe assembly followed by securing it with two bolts at 43 Nm (440 kgf-cm, 32ft-lbf) and two nuts at 62 Nm (632 kgf-cm, 46ft-lbf). Then install the No. 1 exhaust pipe support bracket with 2 new nuts at 21 Nm (214 kgf-cm, 15ft-lbf) before connecting the heated oxygen sensor connector. The installation of the heated oxygen sensor for Bank 1 Sensor 2 should follow the same procedure for Special Service Tool: 09224-00010. Ensure all torque quantities match previous specifications before connecting the heated oxygen sensor connector. Check the exhaust gas leaks by connecting the negative battery cable terminal.

OEM 2009 Toyota Sienna Oxygen Sensor

Oxygen O2 Sensor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

5 Oxygen Sensors found

View related parts
2009 Toyota Sienna Oxygen Sensor, Driver Side
Part Number: 89465-08090
$105.81 MSRP: $148.53
You Save: $42.72 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor, Oxygen; Oxygen Sensor, Rear Left
- Manufacturer Note: LH
- Position: Driver Side
- Part Name Code: 89465
- Item Weight: 0.40 Pounds
- Item Dimensions: 7.4 x 3.5 x 2.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 89465-08090
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2009 Toyota Sienna Submodels:
- CE, LE, Limited, XLE | 6 Cyl 3.5 L GAS
View related parts
2009 Toyota Sienna Oxygen Sensor, Passenger Side
Part Number: 89465-08070
$105.81 MSRP: $148.53
You Save: $42.72 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor, Oxygen; Oxygen Sensor, Rear Right
- Manufacturer Note: RH
- Position: Passenger Side
- Part Name Code: 89465
- Item Weight: 0.40 Pounds
- Item Dimensions: 13.1 x 11.3 x 2.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 89465-08070
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2009 Toyota Sienna Submodels:
- CE, LE, Limited, XLE | 6 Cyl 3.5 L GAS
View related parts
2009 Toyota Sienna Oxygen Sensor, Passenger Side
Part Number: 89467-08040
$199.90 MSRP: $285.41
You Save: $85.51 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor, Air Fuel Rat; Sensor, Air Fuel Ratio
- Manufacturer Note: RH
- Position: Passenger Side
- Replaces: 89467-08020
- Part Name Code: 89467B
- Item Weight: 0.60 Pounds
- Item Dimensions: 13.1 x 11.7 x 2.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 89467-08040
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2009 Toyota Sienna Submodels:
- CE, LE, Limited, XLE, XLE Limited | 6 Cyl 3.3 L GAS, 6 Cyl 3.5 L GAS
View related parts
2009 Toyota Sienna Oxygen Sensor, Passenger Side
Part Number: 89465-08080
$105.81 MSRP: $148.53
You Save: $42.72 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor, Oxygen; Oxygen Sensor, Rear Right
- Manufacturer Note: RH
- Position: Passenger Side
- Part Name Code: 89465
- Item Weight: 0.40 Pounds
- Item Dimensions: 7.5 x 3.6 x 2.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 89465-08080
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2009 Toyota Sienna Submodels:
- CE, LE, Limited, XLE | 6 Cyl 3.5 L GAS
View related parts
2009 Toyota Sienna Oxygen Sensor, Driver Side
Part Number: 89467-08070
$199.90 MSRP: $285.41
You Save: $85.51 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor, Air Fuel Rat; Sensor, Air Fuel Ratio
- Manufacturer Note: LH
- Position: Driver Side
- Replaces: 89467-08030, 89467-08050
- Part Name Code: 89467B
- Item Weight: 0.60 Pounds
- Item Dimensions: 7.5 x 3.7 x 1.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 89467-08070
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2009 Toyota Sienna Submodels:
- CE, LE, Limited, XLE | 6 Cyl 3.5 L GAS

2009 Toyota Sienna Oxygen Sensor

Looking for affordable OEM 2009 Toyota Sienna Oxygen Sensor? Explore our comprehensive catalogue of genuine 2009 Toyota Sienna Oxygen Sensor. All our parts are covered by the manufacturer's warranty. Plus, our straightforward return policy and speedy delivery service ensure an unparalleled shopping experience. We look forward to your visit!

2009 Toyota Sienna Parts Questions & Experts Answers

Q: How to install the heated oxygen sensor for Bank 2 Sensor 2 on 2009 Toyota Sienna?
A: Special Service Tool: 09224-00010 must be used to connect the Bank 2 Sensor 2 heated oxygen sensor to the front exhaust pipe with 40 Nm (408 kgf-cm, 30ft-lbf) torque using the tool while 44 Nm (449 kgf-cm, 32ft-lbf) torque can be achieved without the tool. It requires the use of a torque wrench with a 30 cm (11.81 in.) fullcrum and straight alignment of the tool and wrench. Start by putting two new gaskets onto the front exhaust pipe assembly followed by securing it with two bolts at 43 Nm (440 kgf-cm, 32ft-lbf) and two nuts at 62 Nm (632 kgf-cm, 46ft-lbf). Then install the No. 1 exhaust pipe support bracket with 2 new nuts at 21 Nm (214 kgf-cm, 15ft-lbf) before connecting the heated oxygen sensor connector. The installation of the heated oxygen sensor for Bank 1 Sensor 2 should follow the same procedure for Special Service Tool: 09224-00010. Ensure all torque quantities match previous specifications before connecting the heated oxygen sensor connector. Check the exhaust gas leaks by connecting the negative battery cable terminal.