How to remove and install the Flywheel in the 3.5L V6 engine on a Toyota Highlander?

To completely withdraw the engine/transmission assembly from the car first, it is required to separate the transaxle from the engine. Mark the key ways of the driveplate and crankshaft so it will align properly when it is reinstalled. Remove the old bolts that clamps down the driveplate over the crankshaft, and, if a crankshaft rotates, put a screwdriver under the driveplate to prevent if from turning. Be very slow in the process of pulling out the driveplate and support it while removing the last bolt on the puller, and note that the vehicle automatic transmission has spacers on each side of the driveplate. Regarding the 2GR-FKS engines, understand the crankshaft angle sensor plate and beveled edge washer. Iwash the driveplate in order to remove all chances of grease and oily films, after that I look for cracks on the driveplate and check the condition of the ring gear teeth. Replace the rear crankshaft seal if it comes with one and check and clean the mating surface for the drive-plate and crankshaft. On 2GR-FKS engines, bolt the crankshaft angle sensor plate followed by the proper orientation of the same before the fitting of the driveplate and spacer. Insert the driveplate onto the crankshaft by placing the marks made during the removal of the component back into place if there are alignment dowels or using the staggered bolt holes, in case there are any, to ensure installation of driveplate is correct. Put a thread-locking compound on new bolts and tighten and lock them interlacely in a gradual manner to the final torque magnitude. The subsequent steps of installation procedure are contrary to the removal steps of flash application.

How to remove and install the flywheel/driveplate on Toyota Supra?

Remove the transmission based on whether the vehicle has a manual or automatic transmission. For vehicles with a manual transmission, remove the clutch. The flywheel/driveplate is secured to the rear of the crankshaft with six bolts; loosen and remove these bolts to separate it from the crankshaft flange. When installing the flywheel/driveplate back onto the crankshaft, apply a liquid thread locking compound to the bolts and tighten them gradually in a criss-cross pattern to the specified torque. The installation process follows the reverse order of removal.

OEM Toyota Flywheel

Clutch Flywheel

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

66 Flywheels found

View related parts
Toyota Flywheel Part Number: 13405-28020
$392.36 MSRP: $575.00
You Save: $182.64 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Flywheel Sub-Assembly; Automatic Transmission Flexplate; Clutch Kit
Fits the following Toyota Models:
- Camry | 2002-2010 | Base, CE, LE, SE, XLE | 4 Cyl 2.4 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L GAS, 6 Cyl 3.5 L GAS
- Corolla | 2009-2010 | XRS | 4 Cyl 2.4 L GAS
- Matrix | 2009-2013 | S, XRS | 4 Cyl 2.4 L GAS
- RAV4 | 2001-2005 | Base, L, Sport | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
- Solara | 2002-2008 | SE, SE Sport, SLE, Sport | 4 Cyl 2.4 L GAS, 6 Cyl 3.3 L GAS
View More
View related parts
Toyota Flywheel Part Number: 13405-22020
$372.61 MSRP: $546.07
You Save: $173.46 (32%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Flywheel Sub-Assembly; Clutch Kit
- Manufacturer Note: TYPE A:REFER ILLUST.
- Replaces: 13451-22020
Fits the following Toyota Models:
- Celica | 2000-2005 | GT, GTS | 4 Cyl 1.8 L GAS
- Corolla | 1998-2008 | CE, LE, S, VE | 4 Cyl 1.8 L GAS
- Matrix | 2003-2008 | Base, XR | 4 Cyl 1.8 L GAS
- MR2 Spyder | 2000-2005 | Base | 4 Cyl 1.8 L GAS
View More
View related parts
Toyota Flywheel Sub-Assembly Part Number: 13405-46040
$485.20 MSRP: $711.06
You Save: $225.86 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Clutch Kit
Fits the following Toyota Models:
- Supra | 1993-1997 | Base | 6 Cyl 3.0 L GAS
View related parts
Toyota Flywheel Part Number: 13405-88600
$421.98 MSRP: $618.42
You Save: $196.44 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Flywheel Sub-Assembly; Clutch Kit
Fits the following Toyota Models:
- Celica | 2000-2005 | GT, GTS | 4 Cyl 1.8 L GAS
- Corolla | 2005-2006 | XRS | 4 Cyl 1.8 L GAS
- Matrix | 2003-2006 | XRS | 4 Cyl 1.8 L GAS
View More
View related parts
Toyota Flywheel Part Number: 13405-75060
$440.26 MSRP: $645.19
You Save: $204.93 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Flywheel Sub-Assembly; Clutch Kit
Fits the following Toyota Models:
- Tacoma | 2005-2017 | Base, Pre Runner, SR, SR5 | 4 Cyl 2.7 L GAS
View related parts
Toyota Flywheel Part Number: 13405-31081
$524.25 MSRP: $768.29
You Save: $244.04 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Flywheel Sub-Assembly; Clutch Kit
- Replaces: 13405-31080
Fits the following Toyota Models:
- FJ Cruiser | 2007-2014 | Base, Trail Teams Special Edition, TRD Special Edition | 6 Cyl 4.0 L GAS
- Tacoma | 2005-2015 | Base, Pre Runner, TRD Pro, X-Runner | 6 Cyl 4.0 L GAS
- Tundra | 2005-2006 | Base, Limited, SR5 | 6 Cyl 4.0 L GAS, 8 Cyl 4.7 L GAS
View More
View related parts
Toyota Flywheel Part Number: 13405-75040
$564.65 MSRP: $827.50
You Save: $262.85 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Flywheel Sub-Assembly; Clutch Kit
Fits the following Toyota Models:
- 4Runner | 1996-2000 | Base | 4 Cyl 2.7 L GAS
- T100 | 1994-1998 | Base | 4 Cyl 2.7 L GAS
- Tacoma | 1995-2004 | Base, DLX, Pre Runner, SR5 | 4 Cyl 2.4 L GAS, 4 Cyl 2.7 L GAS
View More
View related parts
Toyota Flywheel Part Number: 13405-62030
$663.96 MSRP: $973.05
You Save: $309.09 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Flywheel Sub-Assembly; Clutch Kit
Fits the following Toyota Models:
- 4Runner | 1996-2000 | Limited, SR5 | 6 Cyl 3.4 L GAS
- T100 | 1995-1998 | Base, DLX, DX, One-Ton DLX, SR5 | 6 Cyl 3.4 L GAS
- Tacoma | 1995-2004 | Base, DLX, Limited, Pre Runner, S-Runner, SR5 | 6 Cyl 3.4 L GAS
- Tundra | 2000-2004 | Base, Limited, SR5 | 6 Cyl 3.4 L GAS, 8 Cyl 4.7 L GAS
View More
View related parts
Toyota Flywheel Part Number: 13405-37051
$320.48 MSRP: $457.57
You Save: $137.09 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Flywheel Sub-Assembly; Clutch Kit
- Replaces: 13405-37050
Fits the following Toyota Models:
- Corolla | 2009-2019 | 50th Anniversary Special Edition, Base, L, LE, LE Eco, Le Eco Plus, S, SE, Special Edition, XLE, XSE | 4 Cyl 1.8 L GAS
- Corolla iM | 2017-2018 | Base | 4 Cyl 1.8 L GAS
- Matrix | 2009-2013 | Base | 4 Cyl 1.8 L GAS
View More
View related parts
Toyota Drive Plate Part Number: 13451-37080
$348.56 MSRP: $497.66
You Save: $149.10 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Flywheel; Flywheel Sub-Assembly
Fits the following Toyota Models:
- Prius | 2010-2015 | Base, Five, Four, One, Persona Series, Three, Two | 4 Cyl 1.8 L FULL HYBRID EV-GAS (FHEV)
- Prius V | 2012-2017 | Base, Five, Four, Three, Two | 4 Cyl 1.8 L FULL HYBRID EV-GAS (FHEV)
View related parts
Toyota Flywheel Part Number: SU003-07231
$347.38 MSRP: $473.45
You Save: $126.07 (27%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Flywheel Assembly; Clutch Kit; Flywheel Sub-Assembly
- Replaces: SU003-04287
Fits the following Toyota Models:
- 86 | 2017-2020 | Base, GT, Hakone Edition, Special Edition, TRD Special Edition | 4 Cyl 2.0 L GAS
View related parts
Toyota Flywheel Sub-Assembly Part Number: 13405-31130
$411.65 MSRP: $603.28
You Save: $191.63 (32%)
Ships in 1-3 Business Days
ADD TO CART
Fits the following Toyota Models:
- Highlander | 2017-2019 | Hybrid LE, Hybrid Limited, Hybrid Limited Platinum, Hybrid XLE | 6 Cyl 3.5 L FULL HYBRID EV-GAS (FHEV)
View related parts
Toyota Flywheel Part Number: 13405-74120
$423.68 MSRP: $620.91
You Save: $197.23 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Flywheel Sub-Assembly; Clutch Kit
- Manufacturer Note: (J)
- Replaces: 13405-74031, 13405-03010
Fits the following Toyota Models:
- Camry | 1990-2001 | Base, CE, DLX, DLX All Trac, DX, LE, LE All Trac, SE, XLE | 4 Cyl 2.0 L GAS, 4 Cyl 2.2 L CNG, 4 Cyl 2.2 L GAS
- Celica | 1990-1999 | GT, GTS | 4 Cyl 2.2 L GAS
- MR2 | 1991-1995 | Base, Turbo | 4 Cyl 2.0 L GAS, 4 Cyl 2.2 L GAS
View More
View related parts
Toyota Drive Plate Part Number: 13451-25030
$369.32 MSRP: $541.24
You Save: $171.92 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Flywheel; Flywheel Sub-Assembly
Fits the following Toyota Models:
- Avalon | 2019-2022 | Hybrid Limited, Hybrid XLE, Hybrid XSE, Hybrid XSE Nightshade | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV)
- Crown | 2023-2025 | Limited, Nightshade, XLE | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV)
- Crown Signia | 2025 | Limited, XLE | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV)
- Highlander | 2020-2024
- Sienna | 2021-2025 | 25th Anniversary Edition, LE, Limited, Platinum, XLE, XSE | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV)
View More
View related parts
Toyota Drive Plate Part Number: 13405-20010
$369.32 MSRP: $541.24
You Save: $171.92 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Flywheel Sub-Assembly
Fits the following Toyota Models:
- Highlander | 2006-2016 | Hybrid, Hybrid Limited | 6 Cyl 3.3 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.5 L FULL HYBRID EV-GAS (FHEV)
View related parts
Toyota Flywheel Sub-Assembly Part Number: 13405-28050
$376.13 MSRP: $551.21
You Save: $175.08 (32%)
Ships in 1-3 Business Days
ADD TO CART
Fits the following Toyota Models:
- Camry | 2007-2011 | Hybrid | 4 Cyl 2.4 L FULL HYBRID EV-GAS (FHEV)
View related parts
Toyota Flywheel Sub-Assembly Part Number: 13451-36040
$392.36 MSRP: $575.00
You Save: $182.64 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Flywheel
Fits the following Toyota Models:
- Avalon | 2013-2018 | Hybrid Limited, Hybrid XLE | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV)
- Camry | 2012-2017 | Hybrid LE, Hybrid SE, Hybrid XLE | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV)
View related parts
Toyota Flywheel Part Number: 13405-74051
$421.97 MSRP: $618.40
You Save: $196.43 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Flywheel Sub-Assembly; Clutch Kit
Fits the following Toyota Models:
- Camry | 1990-1991 | Base, DLX, DLX All Trac, LE, LE All Trac | 4 Cyl 2.0 L GAS
- RAV4 | 1996-2000 | Base | 4 Cyl 2.0 L GAS, BATTERY EV (EV/BEV)
View related parts
Toyota Flywheel Part Number: 13405-15090
$421.98 MSRP: $618.42
You Save: $196.44 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Flywheel Sub-Assembly; Clutch Kit
Fits the following Toyota Models:
- Celica | 1994-1997 | ST | 4 Cyl 1.8 L GAS
- Corolla | 1993-1997 | Base, CE, DX, LE | 4 Cyl 1.6 L GAS, 4 Cyl 1.8 L GAS
View related parts
Toyota Flywheel Sub-Assembly Part Number: 13405-62020
$474.76 MSRP: $695.77
You Save: $221.01 (32%)
Product Specifications
- Other Name: Clutch Kit
Fits the following Toyota Models:
- Camry | 1997-2002, 1989-1993 | CE, DLX, DX, LE, SE, XLE | 6 Cyl 2.5 L GAS, 6 Cyl 3.0 L GAS

| Page 1 of 4 |Next >

1-20 of 66 Results

Toyota Flywheel

OEM parts deliver unmatched quality you can rely on. They pass extensive quality control inspections. Toyota produces them to the official factory specifications. This process helps prevent defects and imperfections. So you can get exceptional lifespan and a flawless fit. Need new OEM Toyota Flywheel? You'll love our wide selection of genuine options. Shop in minutes and skip the hunt. Our prices are unbeatable, you'll save time and money. It's easy to shop and find the right piece. Our committed customer service team gives professional help from start to finish. Every part includes a manufacturer's warranty. We ship quickly, your parts will arrive fast at your door.

Toyota Flywheel stores engine momentum making it take off faster and have a consistent rev in every drive. Toyota has created its name by using lean production that reduces waste, halts the production line when the first defect is detected, and corrects the reason before the bolts turn back. Toyota shares hybrid expertise in compacts, sedans, and SUVs to allow common drivers to conserve fuel and experience additional power as well as retaining common controls beneath their right foot. Toyota uses the TNGA platform to reduce centers of gravity, reduce body rigidity, and give a sensation of stuck cornering with safety electronics lurking in the background quietly. Toyota twins that handling with road-tested longevity that leaves taxis, crossovers, and hatchbacks rolling off in the snowy mornings when competitors rust away. Flywheel is connected to the crank, holding the rotational energy between bangs, even the idle, and provides the starter with a stern ring gear each morning. Flywheel clamps onto the clutch disc and torque is transferred into the gearbox without any shudder which would otherwise crack shafts and mounts. Flywheel choices include simple plain steel to dual mass units concealing spring packs to suppress vibration at the expense of more robust swaps. The Flywheel surfaces get scarred after some time thus it is much better to replace the plate at the initial grind to make the shifts slick and wallets happier in the future.

Toyota Flywheel Parts and Q&A

Flywheel Sub-Assembly
13405-31130
Q: How to remove and install the Flywheel in the 3.5L V6 engine on a Toyota Highlander?
A:
To completely withdraw the engine/transmission assembly from the car first, it is required to separate the transaxle from the engine. Mark the key ways of the driveplate and crankshaft so it will align properly when it is reinstalled. Remove the old bolts that clamps down the driveplate over the crankshaft, and, if a crankshaft rotates, put a screwdriver under the driveplate to prevent if from turning. Be very slow in the process of pulling out the driveplate and support it while removing the last bolt on the puller, and note that the vehicle automatic transmission has spacers on each side of the driveplate. Regarding the 2GR-FKS engines, understand the crankshaft angle sensor plate and beveled edge washer. Iwash the driveplate in order to remove all chances of grease and oily films, after that I look for cracks on the driveplate and check the condition of the ring gear teeth. Replace the rear crankshaft seal if it comes with one and check and clean the mating surface for the drive-plate and crankshaft. On 2GR-FKS engines, bolt the crankshaft angle sensor plate followed by the proper orientation of the same before the fitting of the driveplate and spacer. Insert the driveplate onto the crankshaft by placing the marks made during the removal of the component back into place if there are alignment dowels or using the staggered bolt holes, in case there are any, to ensure installation of driveplate is correct. Put a thread-locking compound on new bolts and tighten and lock them interlacely in a gradual manner to the final torque magnitude. The subsequent steps of installation procedure are contrary to the removal steps of flash application.
Flywheel
13405-42010
Q: How to remove and install the flywheel/driveplate on Toyota Supra?
A:
Remove the transmission based on whether the vehicle has a manual or automatic transmission. For vehicles with a manual transmission, remove the clutch. The flywheel/driveplate is secured to the rear of the crankshaft with six bolts; loosen and remove these bolts to separate it from the crankshaft flange. When installing the flywheel/driveplate back onto the crankshaft, apply a liquid thread locking compound to the bolts and tighten them gradually in a criss-cross pattern to the specified torque. The installation process follows the reverse order of removal.