How to install the exhaust pipe on 2008 Toyota Highlander?

One should start exhaust pipe installation by adding the Bank 2 Sensor 2 heated oxygen sensor for the 2GR-FE engine. First install a new gasket onto the front exhaust pipe assembly before tightening it with two new nuts that need torquing to 56 Nm (571 kgf-cm, 41 ft-lbf). Afterwards attach the heated oxygen sensor for Bank 2 Sensor 2. The installation process for Bank 1 Sensor 2 heated oxygen sensor should follow next. Install the front No. 3 exhaust pipe sub-assembly by setting two new gaskets followed by tightening two new nuts and two bolts to 56 Nm (571 kgf-cm, 41 ft-lbf) while also adding three clamps before connecting the heated oxygen sensor for Bank 1 Sensor 2 then screwing the front exhaust pipe assembly bolt to 21 Nm (214 kgf-cm, 15 ft-lbf). Measure the compression spring free length in the center exhaust pipe assembly using vernier calipers until it shows minimum requirements for replacement. Install and flatten a fresh gasket against the front No. 3 exhaust pipe sub-assembly by using a plastic-faced hammer and wooden block until it reaches the correct installation depth. Discard the used gasket. Please secure the center exhaust pipe assembly by mounting it with two compression springs alongside two bolts following a torque of 48 Nm (489 kgf-cm, 35 ft-lbf). Use two bolts to mount the exhaust pipe damper while torquing them to 19 Nm (194 kgf-cm, 14 ft-lbf). The tail exhaust pipe assembly installation requires free compression spring length measurement for replacement purposes followed by new gasket positioning until it reaches the center exhaust pipe assembly while avoiding reverse installation and reuse of removed gaskets. The exhaust pipe support must be attached to the assembly by using two compression springs and two bolts which should receive a torque setting of 48 Nm (489 kgf-cm, 35 ft-lbf). Exhaust gas leaks should be inspected and the replacement of damaged parts with new components must be performed before installing the No. 2 engine under cover, No. 1 engine under cover, and engine under cover assembly.

OEM 2008 Toyota Highlander Exhaust Pipe

Exhaust Tail Pipe

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

7 Exhaust Pipes found

View related parts
2008 Toyota Highlander Muffler & Pipe, Center
Part Number: 17420-0P150
$1594.18 MSRP: $2139.85
You Save: $545.67 (26%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pipe Assembly, Exhaust; Exhaust Muffler; Exhaust Muffler Assembly; Exhaust Pipe; Tail Pipe; Muffler; Pipe Assembly, Exhaust, Center
- Position: Center
- Replaces: 17420-31180
- Part Name Code: 17420
- Item Weight: 16.40 Pounds
- Item Dimensions: 51.4 x 19.5 x 9.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 17420-0P150
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2008 Toyota Highlander Submodels:
- Base, Limited, SE, Sport | 6 Cyl 3.5 L GAS
View related parts
2008 Toyota Highlander Pipe Sub-Assembly, Exhaust, Front
Part Number: 17403-0P100
$128.79 MSRP: $166.99
You Save: $38.20 (23%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pipe Sub-Assembly, Exhaust; Exhaust System; Exhaust Y Pipe; Exhaust Pipe
- Replaces: 17403-20170
- Part Name Code: 17403
- Item Weight: 5.10 Pounds
- Item Dimensions: 71.5 x 23.3 x 11.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 17403-0P100
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2008 Toyota Highlander Submodels:
- Base, Limited, Plus, SE, Sport | 6 Cyl 3.3 L GAS, 6 Cyl 3.5 L GAS
View related parts
2008 Toyota Highlander Front Pipe
Part Number: 17410-0P180
$261.39 MSRP: $341.83
You Save: $80.44 (24%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pipe Assembly, Exhaust; Exhaust Intermediate Pipe, Front; Exhaust Pipe; Front Shield; Pipe Assembly, Exhaust, Front
- Position: Front
- Replaces: 17410-31660
- Part Name Code: 17410
- Item Weight: 8.10 Pounds
- Item Dimensions: 48.6 x 18.7 x 9.7 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 17410-0P180
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2008 Toyota Highlander Submodels:
- Base, Limited, SE, Sport | 6 Cyl 3.5 L GAS
View related parts
2008 Toyota Highlander Front Pipe
Part Number: 17410-20510
$260.35 MSRP: $340.47
You Save: $80.12 (24%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pipe Assembly, Exhaust; Exhaust Intermediate Pipe, Front; Exhaust Pipe; Pipe Assembly, Exhaust, Front
- Position: Front
- Part Name Code: 17410
- Item Weight: 10.90 Pounds
- Item Dimensions: 47.2 x 18.2 x 9.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 17410-20510
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2008 Toyota Highlander Submodels:
- Hybrid, Hybrid Limited | 6 Cyl 3.3 L FULL HYBRID EV-GAS (FHEV)
View related parts
2008 Toyota Highlander Intermediate Pipe
Part Number: 17403-20190
$228.77 MSRP: $299.17
You Save: $70.40 (24%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pipe Sub-Assembly, Exhaust; Intermediate Pipe, Center; Exhaust System; Y Pipe; Connector Pipe; Extension; Pipe Sub-Assembly, Exhaust, Front
- Part Name Code: 17403
- Item Weight: 15.10 Pounds
- Item Dimensions: 70.1 x 22.2 x 10.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 17403-20190
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2008 Toyota Highlander Submodels:
- Hybrid, Hybrid Limited | 6 Cyl 3.3 L FULL HYBRID EV-GAS (FHEV)
View related parts
2008 Toyota Highlander Tail Pipe
Part Number: 17430-31580
$225.09 MSRP: $294.36
You Save: $69.27 (24%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pipe Assembly, Exhaust Tail; Exhaust Muffler; Direct-Fit Exhaust; Exhaust System Kit; Exhaust Pipe; Rear Muffler; Pipe Assembly, Exhaust, Tail; Muffler
- Part Name Code: 17430
- Item Weight: 10.90 Pounds
- Item Dimensions: 44.9 x 12.2 x 8.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 17430-31580
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2008 Toyota Highlander Submodels:
- Base, Hybrid, Hybrid Limited, Limited, SE, Sport | 6 Cyl 3.3 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.5 L GAS
View related parts
2008 Toyota Highlander Muffler & Pipe, Center
Part Number: 17420-20420
$1714.17 MSRP: $2300.91
You Save: $586.74 (26%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pipe Assembly, Exhaust; Exhaust Intermediate Pipe, Rear; Exhaust Muffler; Exhaust Pipe; Tail Pipe; Muffler; Pipe Assembly, Exhaust, Center
- Position: Center
- Part Name Code: 17420
- Item Weight: 16.30 Pounds
- Item Dimensions: 51.9 x 20.0 x 9.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 17420-20420
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2008 Toyota Highlander Submodels:
- Hybrid, Hybrid Limited | 6 Cyl 3.3 L FULL HYBRID EV-GAS (FHEV)

2008 Toyota Highlander Exhaust Pipe

Looking for affordable OEM 2008 Toyota Highlander Exhaust Pipe? Explore our comprehensive catalogue of genuine 2008 Toyota Highlander Exhaust Pipe. All our parts are covered by the manufacturer's warranty. Plus, our straightforward return policy and speedy delivery service ensure an unparalleled shopping experience. We look forward to your visit!

2008 Toyota Highlander Parts Questions & Experts Answers

Q: How to install the exhaust pipe on 2008 Toyota Highlander?
A: One should start exhaust pipe installation by adding the Bank 2 Sensor 2 heated oxygen sensor for the 2GR-FE engine. First install a new gasket onto the front exhaust pipe assembly before tightening it with two new nuts that need torquing to 56 Nm (571 kgf-cm, 41 ft-lbf). Afterwards attach the heated oxygen sensor for Bank 2 Sensor 2. The installation process for Bank 1 Sensor 2 heated oxygen sensor should follow next. Install the front No. 3 exhaust pipe sub-assembly by setting two new gaskets followed by tightening two new nuts and two bolts to 56 Nm (571 kgf-cm, 41 ft-lbf) while also adding three clamps before connecting the heated oxygen sensor for Bank 1 Sensor 2 then screwing the front exhaust pipe assembly bolt to 21 Nm (214 kgf-cm, 15 ft-lbf). Measure the compression spring free length in the center exhaust pipe assembly using vernier calipers until it shows minimum requirements for replacement. Install and flatten a fresh gasket against the front No. 3 exhaust pipe sub-assembly by using a plastic-faced hammer and wooden block until it reaches the correct installation depth. Discard the used gasket. Please secure the center exhaust pipe assembly by mounting it with two compression springs alongside two bolts following a torque of 48 Nm (489 kgf-cm, 35 ft-lbf). Use two bolts to mount the exhaust pipe damper while torquing them to 19 Nm (194 kgf-cm, 14 ft-lbf). The tail exhaust pipe assembly installation requires free compression spring length measurement for replacement purposes followed by new gasket positioning until it reaches the center exhaust pipe assembly while avoiding reverse installation and reuse of removed gaskets. The exhaust pipe support must be attached to the assembly by using two compression springs and two bolts which should receive a torque setting of 48 Nm (489 kgf-cm, 35 ft-lbf). Exhaust gas leaks should be inspected and the replacement of damaged parts with new components must be performed before installing the No. 2 engine under cover, No. 1 engine under cover, and engine under cover assembly.