How to install the side Air Bag sensor LH on 2008 Toyota Avalon?

Begin the side Air Bag sensor LH installation only after both the ignition switch is off and battery negative (-) terminal is disconnected for at least 90 seconds. Fasten the side Air Bag sensor LH with a torquespec of 9.0 Nm (92 kgf-cm, 80 in-lbf) through the nut. When the side Air Bag sensor LH or its case or connector demonstrate drops or exhibit any damages including cracks or dents the sensor needs replacement with a new unit. The SRS wiring should be assessed to avoid contact with other car components and pinching must be prevented during installation and any loose parts should be examined thoroughly. Install the connector at the side Air Bag sensor LH port position. Move forward with the installation of front seat outer belt assembly and follow it with center pillar garnish lower LH along with rear door opening trim Weather Strip LH then install front door opening trim Weather Strip LH before adding rear door scuff plate LH and front door scuff plate LH. The initialization procedure becomes necessary following battery cable removal for systems that need it. Reinstall the cable at the negative terminal to start initialization. You should conduct an inspection of the SRS warning light to verify its correct functioning.

OEM 2008 Toyota Avalon Air Bag Sensor

Air Bag Impact Sensor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

4 Air Bag Sensors found

View related parts
2008 Toyota Avalon Front Impact Sensor
Part Number: 89173-09390
$86.02 MSRP: $103.71
You Save: $17.69 (18%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor, Air Bag, Front; Air Bag Impact Sensor, Front; Air Bag Sensor; Front Sensor; Sensor, Air Bag, Front Passenger Side; Sensor, Air Bag, Front Driver Side
- Position: Front
- Item Weight: 0.70 Pounds
- Item Dimensions: 4.7 x 2.9 x 2.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 89173-09390
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2008 Toyota Avalon Submodels:
- Base, Limited, Touring, XL, XLS | 6 Cyl 3.5 L GAS
View related parts
2008 Toyota Avalon Position Sensor
Part Number: 89178-06040
$79.24 MSRP: $111.22
You Save: $31.98 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor, Seat Position; Front Left, Right, Left Track; Air Bag Seat Mat; Occupant Detection.; Air Bag Sensor; Occupant Sensor; Sensor; Sensor, Seat Position Air Bag
- Item Weight: 0.50 Pounds
- Item Dimensions: 2.1 x 1.5 x 1.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 89178-06040
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2008 Toyota Avalon Submodels:
- Base, Limited, Touring, XL, XLS | 6 Cyl 3.5 L GAS
View related parts
2008 Toyota Avalon Side Impact Sensor, Lower
Part Number: 89831-02030
$86.14 MSRP: $103.86
You Save: $17.72 (18%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor, Side Air Bag; Air Bag Impact Sensor, Lower; Air Bag Sensor; Side Sensor; Sensor Assembly, Side Air Bag, Passenger Side; Sensor Assembly, Side Air Bag, Driver Side
- Manufacturer Note: NO.1
- Position: Lower
- Item Weight: 0.60 Pounds
- Item Dimensions: 4.2 x 2.6 x 2.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 89831-02030
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2008 Toyota Avalon Submodels:
- Base, Limited, Touring, XL, XLS | 6 Cyl 3.5 L GAS
View related parts
2008 Toyota Avalon Side Impact Sensor, Rear
Part Number: 89831-07010
$110.00 MSRP: $154.41
You Save: $44.41 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor, Side Air Bag; Air Bag Impact Sensor, Rear; Air Bag Sensor; Side Sensor; Sensor Assembly for Passenger/Driver Side Air Bag; Rear Air Bag Sensors.
- Manufacturer Note: SRS AIR BAG-DRIVER,PASSENGER(ADVANCED)&SIDE &CURTAIN,P/N LABEL=8983107010
- Position: Rear
- Item Weight: 0.60 Pounds
- Item Dimensions: 4.3 x 2.6 x 2.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 89831-07010
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2008 Toyota Avalon Submodels:
- Base, Limited, Touring, XL, XLS | 6 Cyl 3.5 L GAS

2008 Toyota Avalon Air Bag Sensor

Looking for affordable OEM 2008 Toyota Avalon Air Bag Sensor? Explore our comprehensive catalogue of genuine 2008 Toyota Avalon Air Bag Sensor. All our parts are covered by the manufacturer's warranty. Plus, our straightforward return policy and speedy delivery service ensure an unparalleled shopping experience. We look forward to your visit!

2008 Toyota Avalon Parts Questions & Experts Answers

Q: How to install the side Air Bag sensor LH on 2008 Toyota Avalon?
A: Begin the side Air Bag sensor LH installation only after both the ignition switch is off and battery negative (-) terminal is disconnected for at least 90 seconds. Fasten the side Air Bag sensor LH with a torquespec of 9.0 Nm (92 kgf-cm, 80 in-lbf) through the nut. When the side Air Bag sensor LH or its case or connector demonstrate drops or exhibit any damages including cracks or dents the sensor needs replacement with a new unit. The SRS wiring should be assessed to avoid contact with other car components and pinching must be prevented during installation and any loose parts should be examined thoroughly. Install the connector at the side Air Bag sensor LH port position. Move forward with the installation of front seat outer belt assembly and follow it with center pillar garnish lower LH along with rear door opening trim Weather Strip LH then install front door opening trim Weather Strip LH before adding rear door scuff plate LH and front door scuff plate LH. The initialization procedure becomes necessary following battery cable removal for systems that need it. Reinstall the cable at the negative terminal to start initialization. You should conduct an inspection of the SRS warning light to verify its correct functioning.