Other Name: Belt Assembly, Rear Seat; Seat Belt Lap and Shoulder Belt, Rear Left; Belt & Retractor; Latch; Belt Assembly, Rear Seat 3 Point Type, Outer Driver Side
Position: Outer Driver Side
Replaces: 73370-04051-B0
Part Name Code: 73370
Item Weight: 2.30 Pounds
Item Dimensions: 11.2 x 8.5 x 5.3 inches
Condition: New
Fitment Type: Direct Replacement
SKU: 73370-04052-B0
Warranty: This genuine part is guaranteed by Toyota's
factory warranty.
More Info
Fits the following 2006 Toyota Tacoma Submodels:
Base, Pre Runner, TRD Pro, X-Runner | 4 Cyl 2.7 L GAS, 6 Cyl 4.0 L GAS
Other Name: Belt Assembly, Rear Seat; Seat Belt Lap and Shoulder Belt, Rear Right; Belt Assembly, Rear Seat 3 Point Type, Outer Passenger Side
Manufacturer Note: FAWN,TRIM4#
Position: Outer Passenger Side
Replaces: 73360-04071-E0
Part Name Code: 73360
Item Weight: 3.20 Pounds
Item Dimensions: 12.0 x 11.0 x 8.4 inches
Condition: New
Fitment Type: Direct Replacement
SKU: 73360-04072-E0
Warranty: This genuine part is guaranteed by Toyota's
factory warranty.
More Info
Fits the following 2006 Toyota Tacoma Submodels:
Base, Pre Runner, X-Runner | 4 Cyl 2.7 L GAS, 6 Cyl 4.0 L GAS
| Page 1 of 2 |Next >
1-20 of 36 Results
2006 Toyota Tacoma Seat Belt
Looking for affordable OEM 2006 Toyota Tacoma Seat Belt? Explore our comprehensive catalogue of genuine 2006 Toyota Tacoma Seat Belt. All our parts are covered by the manufacturer's warranty. Plus, our straightforward return policy and speedy delivery service ensure an unparalleled shopping experience. We look forward to your visit!
2006 Toyota Tacoma Seat Belt Parts Q&A
Q: How to service the seat belt on 2006 Toyota Tacoma?
A: Correct service of the seat belt begins by taking the negative battery cable off followed by a minimum 90-second waiting period to stop Air Bags from triggering. The service begins with unscrewing the access panel rear Weather Strip, lap belt outer anchor cover, along with the door pull handle. Through the use of a screwdriver with tape-wrapped tip you can open the access panel inside handle bezel and extract both screw and panel. Start by removing the rear door trim board sub-assembly through the process of unbolting the front seat outer belt floor anchor and bolt along with disintegration of its clip and 9 clips. To proceed with this part of the procedure remove the access panel inside handle sub-assembly and front seat outer belt assembly after detangling the pretensioner connector from its attachment point. Additionally you need to remove the 2 bolts and retractor. The front shoulder belt anchor adjuster assembly requires bolt removal while releasing its two claws. First install the front shoulder belt anchor adjuster assembly by placing its 2 claws into body holes then bolt it with 42 N.m (430 kgf.cm, 31 ft.lbf) torque. When installing the front seat outer belt assembly you should confirm retractor locking by examining its angular position. Start by hooking the lower stay of the retractor onto the 2 body hooks and then tighten bolt A to 8.5 N.m (85 kgf.cm, 75 in.lbf) and bolt B to 42 N.m (430 kgf.cm, 31 ft.lbf). Finally, connect the pretensioner connector while installing the shoulder anchor with the nut at 42 N.m (430 kgf.cm, 31 ft.lbf). Runs of movement should be smooth for the functioning shoulder anchor while you install the floor anchor by using the bolt and check the ELR lock system after belt application. A front seat outer belt necessitates replacement if it fails to lock after quick pulling of the belt. Begin by removing the bolt and floor anchor followed by access panel inside handle sub-assembly installation along with the three clips which secure the rear door trim board and then attach the panel with its screw. You must reinstall the door handle device through its screw as well as the strap anchor cover and the Weather Strip on the access panel rear section. Finish the process by reconnecting the cable to the negative battery terminal while using a torque of 3.9 N.m (40 kgf.cm, 35 in.lbf) and examining the SRS warning light.