Other Name: Belt Assembly, Rear Seat; Seat Belt Lap and Shoulder Belt, Rear Left; Belt & Retractor; Latch; Belt Assembly, Rear Seat 3 Point Type, Outer Driver Side
Position: Outer Driver Side
Replaces: 73370-04051-B0
Part Name Code: 73370
Item Weight: 2.30 Pounds
Item Dimensions: 11.2 x 8.5 x 5.3 inches
Condition: New
Fitment Type: Direct Replacement
SKU: 73370-04052-B0
Warranty: This genuine part is guaranteed by Toyota's
factory warranty.
More Info
Fits the following 2007 Toyota Tacoma Submodels:
Base, Pre Runner, TRD Pro, X-Runner | 4 Cyl 2.7 L GAS, 6 Cyl 4.0 L GAS
Other Name: Belt Assembly, Rear Seat; Seat Belt Lap and Shoulder Belt, Rear Right; Belt & Retractor; Latch; Belt Assembly, Rear Seat 3 Point Type, Outer Passenger Side
Position: Outer Passenger Side
Replaces: 73360-04071-B0
Part Name Code: 73360
Item Weight: 3.10 Pounds
Item Dimensions: 11.9 x 11.3 x 8.2 inches
Condition: New
Fitment Type: Direct Replacement
SKU: 73360-04072-B0
Warranty: This genuine part is guaranteed by Toyota's
factory warranty.
More Info
Fits the following 2007 Toyota Tacoma Submodels:
Base, Pre Runner, TRD Pro, X-Runner | 4 Cyl 2.7 L GAS, 6 Cyl 4.0 L GAS
| Page 1 of 2 |Next >
1-20 of 37 Results
2007 Toyota Tacoma Seat Belt
Looking for affordable OEM 2007 Toyota Tacoma Seat Belt? Explore our comprehensive catalogue of genuine 2007 Toyota Tacoma Seat Belt. All our parts are covered by the manufacturer's warranty. Plus, our straightforward return policy and speedy delivery service ensure an unparalleled shopping experience. We look forward to your visit!
2007 Toyota Tacoma Parts Questions & Experts Answers
Q: How to remove and install the Front Center Seat Belt for Bench Seat Type on 2007 Toyota Tacoma?
A: You must start the Front Center Seat Outer Belt removal for Bench Seat Type by disengaging all 6 claws on the back panel trim cover then completing the same process on the other side. The next step involves unpocketing the back panel upper garnish followed by the seat belt retractor cover removal by dislodging its 4 clips. Begin removal of the rear center seat outer belt assembly by unfastening its 2 bolts followed by the shoulder anchor and then the 2 bolts and retractor. The 2 bolts need removal to detach the seat belt bracket and after that remove the 2 bolts of the tether anchor bracket sub-assembly. The first step of installation starts with the tether anchor bracket sub-assembly by inserting its claw into the body hole followed by tightening bolt A to 20 N.m then bolt B to 20 N.m (205 kgf.cm, 15 ft.lbf). Fasten the seat belt bracket into place using 2 bolts while torquing them to 20 N.m (205 kgf.cm, 15 ft.lbf). Install the rear seat shoulder belt guide by making sure the retractor inclines properly to secure the belt which should not achieve lock below 15 degrees and must achieve it at 45 degrees or higher. Use the lower retractor stay to connect both hooks of the seat belt bracket before torquing the bolt A to 8.5 N.m and bolt B to 42 N.m. Lastly check the ELR lock function with the seat belt installed by verifying quick pull release locks the belt. Tighten two bolts on the shoulder anchor to 42 N.m (430 kgf.cm, 31 ft.lbf). Install the seat retractor cover with four clips and mount the back panel upper garnish and back panel trim cover using six claws that need repeating on the second side.