How to service the rear shock absorber on 2002 Toyota Sequoia?

Before servicing the rear shock absorber it is necessary to first remove both rear wheels tight with a torque of 110 Nm (1,150 kgf-cm, 83 ft. lbs.). Problem solving requires two steps: first secure the rear axle housing with a jack followed by separating the shock absorber from the axle housing through bolt removal at 87 Nm (887 kgf-cm, 64 ft. lbs.). The other side requires the same procedure where the nut and two retainers and cushion and shock absorber must be removed while applying 58 Nm (591 kgf-cm, 43 ft. lbs) torque to the piston rod before separating the two retainers and cushion from the shock absorber. The installation requires first disconnecting left-hand and right-hand stabilizer bar links using 69 Nm (704 kgf-cm, 51 ft. lbs.) torque for the two nuts before removing the lateral control rod assembly with 140 Nm (1,428 kgf-cm, 103 ft. lbs.) torque for the nut and washer and bolt but torque the bolt and nut only after stabilizing the suspension. The axle housing needs to be lowered slowly to protect the brake line and parking brake cable and to unplug the coil spring, follow spring and insulator and confirm proper alignment of the coil spring end for reinstallation. Compression and extension tests on the shock absorber rod will help identify unusual noises or abnormal resistance; if such issues are detected the device needs replacement. During disposal operations firstly extend the shock absorber rod until fully open then drill a hole at the cylinder while protecting against chip dispersal. To replace the bushing Special Service Tools 09710-14013 (09710-00061) and 09710-28012 (09710-07031), 09950-70010 (09951-07100) must be used with a press to remove the old component and install a fresh one through these same tools. The procedure for installation should be performed in the opposite direction compared to removal.

OEM 2002 Toyota Sequoia Shock Absorber

Suspension Shock Absorber

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

6 Shock Absorbers found

View related parts
2002 Toyota Sequoia Shock Absorber
Part Number: 48530-A9110
$60.30 MSRP: $84.65
You Save: $24.35 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Absorber Assembly, Shock; Rear Shock Absorber; Suspension Kit; Strut Assembly; Shock Set; Strut Kit; Shock; Absorber Assembly, Shock, Rear Passenger Side; Absorber Assembly, Shock, Rear Driver Side
- Manufacturer Note: MARK 48530-AF020
- Item Weight: 7.00 Pounds
- Item Dimensions: 26.4 x 6.6 x 5.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 48530-A9110
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2002 Toyota Sequoia Submodels:
- Limited, SR5 | 8 Cyl 4.7 L GAS
View related parts
2002 Toyota Sequoia Shock Absorber, Front
Part Number: 48510-A9170
$131.71 MSRP: $186.45
You Save: $54.74 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Absorber, Shock, Front; Suspension Kit; Strut Assembly; Shock Set; Complete Strut; Strut; Absorber Assembly, Shock, Front Passenger Side; Absorber Assembly, Shock, Front Driver Side; Shock
- Manufacturer Note: MARK=48510-AF040
- Position: Front
- Item Weight: 6.90 Pounds
- Item Dimensions: 27.1 x 8.5 x 7.7 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 48510-A9170
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2002 Toyota Sequoia Submodels:
- Limited, SR5 | 8 Cyl 4.7 L GAS
View related parts
2002 Toyota Sequoia Shock Absorber, Front
Part Number: 48510-A9180
$127.48 MSRP: $180.45
You Save: $52.97 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Absorber, Shock, Front; Suspension Kit; Strut Assembly; Shock Set; Complete Strut; Strut; Absorber Assembly, Shock, Front Passenger Side; Absorber Assembly, Shock, Front Driver Side; Shock
- Manufacturer Note: MARK=48510-AF050
- Position: Front
- Item Weight: 9.70 Pounds
- Item Dimensions: 26.6 x 8.2 x 7.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 48510-A9180
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2002 Toyota Sequoia Submodels:
- Limited, SR5 | 8 Cyl 4.7 L GAS
View related parts
2002 Toyota Sequoia Shock Absorber
Part Number: 48530-A9180
$88.27 MSRP: $123.91
You Save: $35.64 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Absorber Assembly, Shock; Rear Shock Absorber; Suspension Kit; Strut Assembly; Shock Set; Strut Kit; Shock; Absorber Assembly, Shock, Rear Passenger Side; Absorber Assembly, Shock, Rear Driver Side
- Manufacturer Note: MARK 48530-AF021
- Item Weight: 7.10 Pounds
- Item Dimensions: 26.1 x 6.5 x 5.9 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 48530-A9180
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2002 Toyota Sequoia Submodels:
- Limited, SR5 | 8 Cyl 4.7 L GAS
View related parts
2002 Toyota Sequoia Shock Absorber
Part Number: 48510-09760
$133.94 MSRP: $189.60
You Save: $55.66 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Absorber Assembly, Shock; Front Shock Absorber; Suspension Kit; Strut Assembly; Shock Set; Strut Kit; Strut; Absorber Assembly, Shock, Front Passenger Side; Absorber Assembly, Shock, Front Driver Side; Shock
- Manufacturer Note: MARK 48510-AF060
- Replaces: 48510-A9130
- Item Weight: 9.90 Pounds
- Item Dimensions: 26.4 x 8.2 x 7.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 48510-09760
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2002 Toyota Sequoia Submodels:
- Limited, SR5 | 8 Cyl 4.7 L GAS
View related parts
2002 Toyota Sequoia Shock Absorber
Part Number: 48530-A9170
$91.83 MSRP: $128.89
You Save: $37.06 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Absorber Assembly, Shock; Rear Shock Absorber; Suspension Kit; Strut Assembly; Shock Set; Strut Kit; Shock; Absorber Assembly, Shock, Rear Passenger Side; Absorber Assembly, Shock, Rear Driver Side
- Manufacturer Note: MARK 48530-AF011
- Item Weight: 1.90 Pounds
- Item Dimensions: 25.6 x 6.6 x 5.9 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 48530-A9170
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2002 Toyota Sequoia Submodels:
- Limited, SR5 | 8 Cyl 4.7 L GAS

2002 Toyota Sequoia Shock Absorber

Looking for affordable OEM 2002 Toyota Sequoia Shock Absorber? Explore our comprehensive catalogue of genuine 2002 Toyota Sequoia Shock Absorber. All our parts are covered by the manufacturer's warranty. Plus, our straightforward return policy and speedy delivery service ensure an unparalleled shopping experience. We look forward to your visit!

2002 Toyota Sequoia Parts Questions & Experts Answers

Q: How to service the rear shock absorber on 2002 Toyota Sequoia?
A: Before servicing the rear shock absorber it is necessary to first remove both rear wheels tight with a torque of 110 Nm (1,150 kgf-cm, 83 ft. lbs.). Problem solving requires two steps: first secure the rear axle housing with a jack followed by separating the shock absorber from the axle housing through bolt removal at 87 Nm (887 kgf-cm, 64 ft. lbs.). The other side requires the same procedure where the nut and two retainers and cushion and shock absorber must be removed while applying 58 Nm (591 kgf-cm, 43 ft. lbs) torque to the piston rod before separating the two retainers and cushion from the shock absorber. The installation requires first disconnecting left-hand and right-hand stabilizer bar links using 69 Nm (704 kgf-cm, 51 ft. lbs.) torque for the two nuts before removing the lateral control rod assembly with 140 Nm (1,428 kgf-cm, 103 ft. lbs.) torque for the nut and washer and bolt but torque the bolt and nut only after stabilizing the suspension. The axle housing needs to be lowered slowly to protect the brake line and parking brake cable and to unplug the coil spring, follow spring and insulator and confirm proper alignment of the coil spring end for reinstallation. Compression and extension tests on the shock absorber rod will help identify unusual noises or abnormal resistance; if such issues are detected the device needs replacement. During disposal operations firstly extend the shock absorber rod until fully open then drill a hole at the cylinder while protecting against chip dispersal. To replace the bushing Special Service Tools 09710-14013 (09710-00061) and 09710-28012 (09710-07031), 09950-70010 (09951-07100) must be used with a press to remove the old component and install a fresh one through these same tools. The procedure for installation should be performed in the opposite direction compared to removal.