How to remove the ABS Control Module for the Antilock Brakes on Toyota Matrix?

The first step for Hydraulic Control Assembly removal from Antilock Brakes demands users to drain brake fluid then prompt immediate cleaning of any paint-layered fluid residues. Begin by taking out the front wheel RH and then detach the front fender liner RH before you can take off the front bumper cover. The next step involves removing both the LH headlight assembly together with the windshield washer jar assembly. Begin by removing the actuator connector and utilize Special Service Tool: 09023-00101 to disconnect six brake tubes which are attached to the bracket. Proper labeling must be performed for future reinstallation. Separate the actuator with bracket by removing two bolts and a nut with caution toward the brake tubes and wire harness. The ABS and traction actuator assembly comes off from its bracket through the removal of two nuts.

How to install the ABS Control Module and its associated components on Toyota Matrix?

Use 2 nuts torque to 6.0 Nm (61 kgf-cm, 53 in-lbf) for fixing the ABS and traction actuator assembly to the bracket. The brake actuator goes next with bracket attachment using 2 bolts and a nut while observing a torque of 20 Nm (204 kgf-cm, 15 ft-lbf). Avoid damaging brake tubes and wire harnesses when performing the installation which requires sequential bolt tightening starting from 1 to 3. Complete the connection of the actuator connector making sure the lever has proper securement. Use Special Service Tool: 09023-00101 to link brake tubes at the proper locations of the actuator with bracket while applying 15 Nm torque force (155 kgf-cm or 11 ft-lbf) to each connection. The windshield washer jar assembly as well as the LH headlight assembly require installation followed by the front bumper cover and front fender liner RH and front wheel RH which should be torqued to a total 103 Nm (1,050 kgf-cm, 76 ft-lbf). The brake fluid reservoir needs to be filled after which you can perform master cylinder bleeding through Special Service Tool: 09023-00101 before bleeding the brake line and the ABS and traction actuator assembly. Check the brake fluid level inside the reservoir while also searching for any brake fluid leaks. Techstream verification of the actuator leads to yaw rate sensor zero point calibration and the vehicle needs preparation for fog light aiming adjustment then fog light aiming needs a thorough inspection and adjustment. The last step includes headlamp aiming preparation followed by inspection and necessary adjustments of the headlamp beam system.

OEM Toyota Matrix ABS Control Module

Anti Lock Brake Control Module

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

24 ABS Control Modules found

View related parts
Toyota Matrix Modulator Valve
Part Number: 44050-02340
$1057.62 MSRP: $1331.33
You Save: $273.71 (21%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Actuator Assembly, Brake; ABS Hydraulic Assembly; ABS Pump And Motor Assembly; ABS Control Module; Actuator Assembly
- Manufacturer Note: VSC-WITH(W/CUT OFF SW)
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2009 Toyota Matrix | S | 4 Cyl 2.4 L GAS
View related parts
Toyota Matrix Modulator Valve
Part Number: 44050-02331
$1089.13 MSRP: $1371.01
You Save: $281.88 (21%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Actuator Assembly, Brake; ABS Hydraulic Assembly; ABS Pump And Motor Assembly; ABS Control Module; Actuator Assembly
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2009-2010 Toyota Matrix | XRS | 4 Cyl 2.4 L GAS
View related parts
Toyota Matrix Modulator Valve
Part Number: 44050-01050
$1587.72 MSRP: $1998.63
You Save: $410.91 (21%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Actuator Assembly, Brake; ABS Hydraulic Assembly; ABS Pump And Motor Assembly; ABS Control Module; Actuator Assembly
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2005-2006 Toyota Matrix | Base, XR | 4 Cyl 1.8 L GAS
View related parts
Toyota Matrix Modulator Valve
Part Number: 44050-02560
$1132.13 MSRP: $1425.12
You Save: $292.99 (21%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Actuator Assembly, Brake; ABS Pump And Motor Assembly; ABS Control Module; Actuator Assembly
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2011 Toyota Matrix | S | 4 Cyl 2.4 L GAS
View related parts
Toyota Matrix Modulator Valve
Part Number: 44050-02322
$1071.10 MSRP: $1348.30
You Save: $277.20 (21%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Actuator Assembly, Brake; ABS Hydraulic Assembly; ABS Control Module
- Manufacturer Note: VSC-WITH(W/CUT OFF SW)
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2010 Toyota Matrix | S, XRS | 4 Cyl 2.4 L GAS
View related parts
Toyota Matrix Modulator Valve
Part Number: 44050-02580
$1132.13 MSRP: $1425.12
You Save: $292.99 (21%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Actuator Assembly, Brake; ABS Pump And Motor Assembly; ABS Control Module; Actuator Assembly
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2011 Toyota Matrix | S | 4 Cyl 2.4 L GAS
View related parts
Toyota Matrix Modulator Valve
Part Number: 44050-02562
$1272.56 MSRP: $1864.95
You Save: $592.39 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Actuator Assembly, Brake; ABS Hydraulic Assembly; ABS Pump And Motor Assembly; ABS Control Module; Actuator Assembly
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2012-2013 Toyota Matrix | S | 4 Cyl 2.4 L GAS
View related parts
Toyota Matrix Modulator Valve
Part Number: 44050-02552
$1269.26 MSRP: $1860.12
You Save: $590.86 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Actuator Assembly, Brake; ABS Hydraulic Assembly; ABS Pump And Motor Assembly; ABS Control Module; Actuator Assembly
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2012-2013 Toyota Matrix | Base | 4 Cyl 1.8 L GAS
View related parts
Toyota Matrix Modulator Valve
Part Number: 44050-02582
$1272.56 MSRP: $1864.95
You Save: $592.39 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Actuator Assembly, Brake; ABS Hydraulic Assembly; ABS Pump And Motor Assembly; ABS Control Module; Actuator Assembly
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2012-2013 Toyota Matrix | S | 4 Cyl 2.4 L GAS
View related parts
Toyota Matrix Actuator Assembly
Part Number: 44050-02321
$905.87 MSRP: $1140.31
You Save: $234.44 (21%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Actuator Assembly, Brake; ABS Hydraulic Assembly; ABS Pump And Motor Assembly; ABS Control Module
- Manufacturer Note: VSC-WITH(W/CUT OFF SW)
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2010 Toyota Matrix | S | 4 Cyl 2.4 L GAS
View related parts
Toyota Matrix Actuator Assembly
Part Number: 44050-02341
$1125.26 MSRP: $1416.48
You Save: $291.22 (21%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Actuator Assembly, Brake; ABS Hydraulic Assembly; ABS Pump And Motor Assembly; ABS Control Module
- Manufacturer Note: VSC-WITH(W/CUT OFF SW)
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2010 Toyota Matrix | S | 4 Cyl 2.4 L GAS
View related parts
Toyota Matrix Modulator Valve
Part Number: 44050-02342
$1111.04 MSRP: $1398.58
You Save: $287.54 (21%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Actuator Assembly, Brake; ABS Hydraulic Assembly; ABS Control Module
- Manufacturer Note: VSC-WITH(W/CUT OFF SW)
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2010 Toyota Matrix | S | 4 Cyl 2.4 L GAS
View related parts
Toyota Matrix Modulator Valve
Part Number: 44050-01011
$773.04 MSRP: $973.10
You Save: $200.06 (21%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Actuator Assembly, Brake; ABS Hydraulic Assembly; ABS Pump And Motor Assembly; ABS Control Module; Actuator Assembly
- Replaces: 44050-01010
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2003-2004 Toyota Matrix | Base, XR, XRS | 4 Cyl 1.8 L GAS
View related parts
Toyota Matrix Modulator Valve
Part Number: 44050-02310
$1032.31 MSRP: $1299.48
You Save: $267.17 (21%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Actuator Assembly, Brake; ABS Hydraulic Assembly; ABS Pump And Motor Assembly; ABS Control Module; Actuator Assembly
- Manufacturer Note: VSC-WITH(W/CUT OFF SW)
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2009 Toyota Matrix | Base | 4 Cyl 1.8 L GAS
View related parts
Toyota Matrix Actuator Assembly
Part Number: 44050-02550
$1013.43 MSRP: $1275.72
You Save: $262.29 (21%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Actuator Assembly, Brake; ABS Pump And Motor Assembly; ABS Control Module
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2011 Toyota Matrix | Base | 4 Cyl 1.8 L GAS
View related parts
Toyota Matrix Modulator Valve
Part Number: 44050-02320
$1125.26 MSRP: $1416.48
You Save: $291.22 (21%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Actuator Assembly, Brake; ABS Pump And Motor Assembly; ABS Control Module; Actuator Assembly
- Manufacturer Note: VSC-WITH(W/CUT OFF SW)
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2009 Toyota Matrix | S, XRS | 4 Cyl 2.4 L GAS
View related parts
Toyota Matrix Modulator Valve
Part Number: 44050-02280
$717.42 MSRP: $903.10
You Save: $185.68 (21%)
Product Specifications
- Other Name: Actuator Assembly, Brake; ABS Hydraulic Assembly; ABS Pump And Motor Assembly; ABS Control Module; Actuator Assembly
- Manufacturer Note: MEXICO SPEC&TIRE & DISK WHEEL-205/55R16 PCD100ST MEXICO
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2009-2010 Toyota Matrix | Base | 4 Cyl 1.8 L GAS
View related parts
Toyota Matrix Modulator Valve
Part Number: 44050-02470
$1057.35 MSRP: $1331.00
You Save: $273.65 (21%)
Product Specifications
- Other Name: Actuator Assembly, Brake; ABS Hydraulic Assembly; ABS Pump And Motor Assembly; ABS Control Module; Actuator Assembly
- Manufacturer Note: VSC-WITH(W/CUT OFF SW) V2P
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2010-2011 Toyota Matrix | Base | 4 Cyl 1.8 L GAS
View related parts
Toyota Matrix Modulator Valve
Part Number: 44050-01020
Product Specifications
- Other Name: Actuator Assembly, Brake; ABS Hydraulic Assembly; ABS Pump And Motor Assembly; ABS Control Module; Actuator Assembly
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2003-2004 Toyota Matrix | Base, XR, XRS | 4 Cyl 1.8 L GAS
View related parts
Toyota Matrix Modulator Valve
Part Number: 44050-12200
Product Specifications
- Other Name: Actuator Assembly, Brake; ABS Pump And Motor Assembly; ABS Control Module; Actuator Assembly; Actuator Assembly, ABS & Traction
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2005-2008 Toyota Matrix | Base, XR, XRS | 4 Cyl 1.8 L GAS

| Page 1 of 2 |Next >

1-20 of 24 Results

Toyota Matrix ABS Control Module

Choose genuine ABS Control Module that pass strict quality control tests. You can trust the top quality and lasting durability. Shopping for OEM ABS Control Module for your Toyota Matrix? Our website is your one-stop destination. We stock an extensive selection of genuine Toyota Matrix parts. The price is affordable so you can save more. It only takes minutes to browse and find the exact fit. Easily add to cart and check out fast. Our hassle-free return policy will keep you stress-free. We process orders quickly for swift delivery. Your parts will arrive faster, so you can get back on the road sooner.

This is one of the systems developed by Toyota to support the Matrix and other models' anti-lock braking system, which is considered highly efficient and demanding in terms of quality. Used to stop wheel lock during maximum brake force, the ABS Control Module aid in manipulating the wheels and generally improves the safety of a vehicle by utilizing sensors that determine the speed of the wheels' rotation. When the potential lock conditions are ascertained, the denomination varies and the brake pressure is altered with valve and hydraulic pressure re-established by a pump to demanded braking specification. The Toyota Matrix manufactured between the year 2002 and 2014 has Abs Control Module different versions, which include the ESC and traction control. These features improve the handling during a skid by selectively applying brake to each of the wheels, thus improving the general driving or maneuvering ability of the car. Toyota Matrix is available in several sub-models which are the Standard, XR, XRS as well as; M-Theory all these prove the adaptability of the featured ABS Control Module across various non-standard power units. Situations when the ABS can potentially make stopping distances even longer include cases of low friction coefficient road surfaces such as loose gravel or snow although overall the benefits of the ABS are also seen in reductions of most overall stopping distances. The major selling factor of the Toyota Matrix ABS Control Module in the market is its reliability through design and addition of functional features and aspects that aim at improving safety and performance of automobiles.

Toyota Matrix ABS Control Module Parts and Q&A

Modulator Valve
44050-12200
Q: How to remove the ABS Control Module for the Antilock Brakes on Toyota Matrix?
A:
The first step for Hydraulic Control Assembly removal from Antilock Brakes demands users to drain brake fluid then prompt immediate cleaning of any paint-layered fluid residues. Begin by taking out the front wheel RH and then detach the front fender liner RH before you can take off the front bumper cover. The next step involves removing both the LH headlight assembly together with the windshield washer jar assembly. Begin by removing the actuator connector and utilize Special Service Tool: 09023-00101 to disconnect six brake tubes which are attached to the bracket. Proper labeling must be performed for future reinstallation. Separate the actuator with bracket by removing two bolts and a nut with caution toward the brake tubes and wire harness. The ABS and traction actuator assembly comes off from its bracket through the removal of two nuts.
Actuator Assembly
44050-01040
Q: How to install the ABS Control Module and its associated components on Toyota Matrix?
A:
Use 2 nuts torque to 6.0 Nm (61 kgf-cm, 53 in-lbf) for fixing the ABS and traction actuator assembly to the bracket. The brake actuator goes next with bracket attachment using 2 bolts and a nut while observing a torque of 20 Nm (204 kgf-cm, 15 ft-lbf). Avoid damaging brake tubes and wire harnesses when performing the installation which requires sequential bolt tightening starting from 1 to 3. Complete the connection of the actuator connector making sure the lever has proper securement. Use Special Service Tool: 09023-00101 to link brake tubes at the proper locations of the actuator with bracket while applying 15 Nm torque force (155 kgf-cm or 11 ft-lbf) to each connection. The windshield washer jar assembly as well as the LH headlight assembly require installation followed by the front bumper cover and front fender liner RH and front wheel RH which should be torqued to a total 103 Nm (1,050 kgf-cm, 76 ft-lbf). The brake fluid reservoir needs to be filled after which you can perform master cylinder bleeding through Special Service Tool: 09023-00101 before bleeding the Brake Line and the ABS and traction actuator assembly. Check the brake fluid level inside the reservoir while also searching for any brake fluid leaks. Techstream verification of the actuator leads to yaw rate sensor zero point calibration and the vehicle needs preparation for fog light aiming adjustment then fog light aiming needs a thorough inspection and adjustment. The last step includes headlamp aiming preparation followed by inspection and necessary adjustments of the headlamp beam system.

Related Toyota Matrix Parts

Browse Toyota Matrix ABS Control Module by Years

2013 2012 2011 2010 2009 2008 2007 2006 2005 2004 2003