How to replace the rear Brake Pad Set on Toyota Celica?

You need to start pad replacement by removing the rear wheel to measure pad lining thickness which must remain above 1.0 mm (0.039 inch). Proceed by removing the clip and 2 anti-rattle springs and 2 pad guide pins using a screwdriver but be careful to maintain normal shape and flexibility because reusable parts include the clip and springs if they retain good condition. You should remove the two pads and anti-squeal shims which are attached to each pad. New pad installation should follow a measurement of disc thickness and runout and a practice of replacing each pad with its anti-squeal shim. Place disc brake grease on the inside area of the anti-squeal shims before positioning both shims onto the pads. Press in the brake piston by using a hammer handle or other equivalent tool while drawing a small amount of brake fluid and possibly needing to detach the bleeder plug first. You should put the inner pad into place with pad wear indicator plates facing up and follow it with the outer pad. Verify that friction surfaces stay free of oil and grease. You should press the anti-rattle springs before inserting the 2 pad guide pins and clip while installing the components. To finish reinstall the rear wheel and torque it to 103 Nm (1,050 kgf-cm, 76 ft. lbs.) and perform several brake pedal depressions and verify the fluid rests at the top of the container.

How to replace the front Brake Pad Set on Toyota Celica?

First remove the front wheel and check the pad lining thickness through the caliper inspection hole before pad replacement when the lining thickness falls below 1.0 mm (0.039 inch). Holding the sliding pin in place enable you to lift the caliper and remove its bottom installation bolt while keeping the flexible hose intact with the brake caliper before securely suspending the caliper. The maintainer should begin by removing the pads along with their corresponding anti-squeal shims and pad wear indicator plates before proceeding with the two pad support plates. These plates can be reused when free of deformation, cracks, and wear and Rust and Dirt are absent. Disk measurement results lead to placing two support pad holders correctly. Install these plates only when disc runout values pass inspection. Replace all pads with new ones as well as their corresponding anti-squeal shims and wear indicator plates during installation; users of the 2ZZ-GE engine must put a pad wear indicator on each pad and must spread grease on both sides of each inner anti-squeal shim and users of the 1ZZ-FE engine need to distribute the grease on the outside edge of the inner anti-squeal shim. After installing the two anti-squeal shims on each pad apply them in a position where the pad wear indicator plate points upward while ensuring the friction surfaces remain free of oil or grease residue. A small amount of fluid should be drawn from the reservoir before pressing the piston inward using a hammer handle or equivalent tool; when piston resistance is high loosen the bleeder plug to vent fluid while pushing in the piston. Position the caliper after keeping the sliding pin intact during installation before tightening bolts to 34 Nm (350 kgf-cm, 25 ft. lbs.). Install the front wheel before torquing it to 103 Nm (1,050 kgf-cm, 76 ft. lbs.). Then depress the brake pedal several times to check the fluid level reaches the max line.

OEM Toyota Celica Brake Pad Set

Disc Brake Pad Set

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

15 Brake Pad Sets found

View related parts
Toyota Celica Pad Kit, Disc Brake
Part Number: 04466-32050
$46.47 MSRP: $64.61
You Save: $18.14 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Disc Brake Pad Set; Brake Pads
- Replaces: 04492-20061, 04491-33070, 04492-20100, 04492-32080, 04492-32070, 04492-32061, 04492-33010, 04466-32010, 04492-20090, 04492-33020, 04492-20062
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1991-1997 Toyota Celica | All Trac, GT, GTS, GTS All Trac, ST | 4 Cyl 1.6 L GAS, 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.2 L GAS
View related parts
Toyota Celica Brake Pads
Part Number: 04465-33021
$76.07 MSRP: $105.63
You Save: $29.56 (28%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Disc Brake; Disc Brake Pad Kit; Disc Brake Pad Set; Front Pads; Pads
- Replaces: 04465-12530, 04465-12110, 04491-02030, 04491-12640, 04491-2B050, 04465-20450, 04465-02020, 04465-20140
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1994-1997 Toyota Celica | GT, ST | 4 Cyl 1.8 L GAS, 4 Cyl 2.2 L GAS
View related parts
Toyota Celica Brake Pads, Rear
Part Number: 04466-20090
$38.71 MSRP: $53.81
You Save: $15.10 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pas Kit, Disc Brake; Disc Brake Pad Set, Rear; Brake Pad Set, Disc Brake; Disc Brake Pad Kit; Rear Pads; Pad Kit, Disc Brake, Rear; Disc Brake Pad Set
- Manufacturer Note: MARK AK PA544
- Position: Rear
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2000-2005 Toyota Celica | GT, GTS | 4 Cyl 1.8 L GAS
View related parts
Toyota Celica Brake Pads, Rear
Part Number: 04466-20020
$46.47 MSRP: $64.61
You Save: $18.14 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Disc Brake, Rear; Disc Brake Pad Kit; Disc Brake Pad Set; Rear Pads
- Position: Rear
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1996-1999 Toyota Celica | GT, ST | 4 Cyl 1.8 L GAS, 4 Cyl 2.2 L GAS
View related parts
Toyota Celica Pad Kit, Disc Brake, Front
Part Number: 04465-33060
$75.25 MSRP: $104.50
You Save: $29.25 (28%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Disc Brake Pad Set; Brake Pads
- Manufacturer Note: MARD AKEBONO PA533A
- Position: Front
- Replaces: 04465-06020, 04491-06020, 04491-07010, 04465-33010, 04491-33021, 04491-33020, 04491-33110, 04491-33100
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1994-1999 Toyota Celica | GT, ST | 4 Cyl 1.8 L GAS, 4 Cyl 2.2 L GAS
View related parts
Toyota Celica Brake Pads, Front
Part Number: 04465-2B010
$46.47 MSRP: $64.61
You Save: $18.14 (29%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Disc Brake; Disc Brake Pad Set, Front; Brake Pad Set, Disc Brake; Disc Brake Pad Kit; Front Pads; Pad Kit, Disc Brake, Front; Disc Brake Pad Set
- Position: Front
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2000-2002 Toyota Celica | GT, GTS | 4 Cyl 1.8 L GAS
View related parts
Toyota Celica Brake Pads, Front
Part Number: 04465-20540
$46.47 MSRP: $64.61
You Save: $18.14 (29%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Disc Brake; Disc Brake Pad Set, Front; Disc Brake Pad Kit; Front Pads; Pad Kit, Disc Brake, Front; Disc Brake Pad Set
- Manufacturer Note: MARK AISIN PC554
- Position: Front
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2003-2005 Toyota Celica | GT, GTS | 4 Cyl 1.8 L GAS
View related parts
Toyota Celica Pads, Rear
Part Number: 04466-22110
$42.65 MSRP: $59.30
You Save: $16.65 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Disc Brake; Disc Brake Pad Set; Brake Pads; Pad Kit, Disc Brake, Rear
- Position: Rear
- Replaces: 04492-14090, 04492-22050, 04492-22043, 04492-14100, 04492-22040, 04492-22070
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1984-1985 Toyota Celica
View related parts
Toyota Celica Front Pads
Part Number: 04465-YZZB4
$45.30 MSRP: $63.08
You Save: $17.78 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Brake Pad; Brake Pads
- Replaces: 04465-20050, 04491-20850, 04491-20860, 04491-20690, 04465-20310, 04491-20660, 04465-20090, 04465-20220
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1990-1993 Toyota Celica | All Trac, GT, GTS All Trac, ST | 4 Cyl 1.6 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.2 L GAS
View related parts
Toyota Celica Brake Pads
Part Number: 04465-47030
$42.65 MSRP: $59.30
You Save: $16.65 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Disc Brake; Disc Brake Pad Set, Front; Brake Pad Set, Disc Brake; Disc Brake Pad Kit; Disc Brake Pad Set; Front Pads
- Replaces: 04465-20480
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2000-2001 Toyota Celica | GT, GTS | 4 Cyl 1.8 L GAS
View related parts
Toyota Celica Front Pads
Part Number: 04465-YZZB7
Product Specifications
- Other Name: Brake Pad; Brake Pads; Pads
- Replaces: 04491-14130, 04491-14131, 04465-14061, 04465-14060
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1984-1985 Toyota Celica
View related parts
Toyota Celica Brake Pads
Part Number: 04465-YZZA2
Product Specifications
- Other Name: Brake Pad; Disc Brake Pad Kit; Disc Brake Pad Set; Front Pads; Pads
- Replaces: 04465-YZZ03, 04491-17040, 04491-32123, 04465-20070, 04465-20080, 04491-17061, 04491-20321, 04491-20561, 04491-20560, 04491-12340, 04491-20202, 04491-20320, 04491-12291, 04491-12342, 04491-12341, 04491-17070, 04491-17071, 04465-17021, 04465-20071, 04465-17020, 04491-17030, 04491-20340, 04465-20030, 04491-20610, 04491-12290, 04491-17050, 04491-17060
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1986-1991 Toyota Celica | GT, GTS, ST | 4 Cyl 1.6 L GAS, 4 Cyl 2.0 L GAS
View related parts
Toyota Celica Front Pads
Part Number: 04465-20430
Product Specifications
- Other Name: Pad Kit, Disc Brake; Brake Pads; Pad Kit, Disc Brake, Front
- Position: Front
- Replaces: 04465-20410, 04491-20360
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1989 Toyota Celica | All Trac | 4 Cyl 2.0 L GAS
View related parts
Toyota Celica Brake Pads
Part Number: 04465-YZZA3
Product Specifications
- Other Name: Brake Pad; Front Pads; Pads
- Replaces: 04465-32040, 04465-32170, 04491-32131, 04491-32290, 04465-YZZ04, 04491-32280, 04491-32291, 04491-32200, 04465-32070, 04465-32091, 04491-32250, 04491-32400, 04491-32251, 04491-32320, 04491-32201, 04491-32281, 04465-32090, 04465-32060
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1988-1989 Toyota Celica | GTS | 4 Cyl 2.0 L GAS
View related parts
Toyota Celica Brake Pads, Rear
Part Number: 04466-33010
$46.47 MSRP: $64.61
You Save: $18.14 (29%)
Product Specifications
- Other Name: Pad Kit, Disc Brake, Rear; Disc Brake Pad Kit; Disc Brake Pad Set; Rear Pads
- Manufacturer Note: MARK AK PA511
- Position: Rear
- Replaces: 04492-20051, 04492-20150, 04492-20040, 04492-20050, 04492-32040, 04492-32011, 04492-32041, 04492-20011, 04492-20010, 04466-20040, 04492-20060
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1988-1991 Toyota Celica | All Trac, GT, GTS, ST | 4 Cyl 1.6 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.2 L GAS

Toyota Celica Brake Pad Set

Choose genuine Brake Pad Set that pass strict quality control tests. You can trust the top quality and lasting durability. Shopping for OEM Brake Pad Set for your Toyota Celica? Our website is your one-stop destination. We stock an extensive selection of genuine Toyota Celica parts. The price is affordable so you can save more. It only takes minutes to browse and find the exact fit. Easily add to cart and check out fast. Our hassle-free return policy will keep you stress-free. We process orders quickly for swift delivery. Your parts will arrive faster, so you can get back on the road sooner.

Toyota Celica Brake Pad Set Parts and Q&A

Brake Pads, Rear
04466-20090
Q: How to replace the rear Brake Pad Set on Toyota Celica?
A:
You need to start pad replacement by removing the rear wheel to measure pad lining thickness which must remain above 1.0 mm (0.039 inch). Proceed by removing the clip and 2 anti-rattle springs and 2 pad guide pins using a screwdriver but be careful to maintain normal shape and flexibility because reusable parts include the clip and springs if they retain good condition. You should remove the two pads and anti-squeal shims which are attached to each pad. New pad installation should follow a measurement of disc thickness and runout and a practice of replacing each pad with its anti-squeal shim. Place disc brake grease on the inside area of the anti-squeal shims before positioning both shims onto the pads. Press in the brake piston by using a hammer handle or other equivalent tool while drawing a small amount of brake fluid and possibly needing to detach the bleeder plug first. You should put the inner pad into place with pad wear indicator plates facing up and follow it with the outer pad. Verify that friction surfaces stay free of oil and grease. You should press the anti-rattle springs before inserting the 2 pad guide pins and clip while installing the components. To finish reinstall the rear wheel and torque it to 103 Nm (1,050 kgf-cm, 76 ft. lbs.) and perform several brake pedal depressions and verify the fluid rests at the top of the container.
Brake Pads, Front
04465-2B010
Q: How to replace the front Brake Pad Set on Toyota Celica?
A:
First remove the front wheel and check the pad lining thickness through the caliper inspection hole before pad replacement when the lining thickness falls below 1.0 mm (0.039 inch). Holding the sliding pin in place enable you to lift the caliper and remove its bottom installation bolt while keeping the flexible hose intact with the brake caliper before securely suspending the caliper. The maintainer should begin by removing the pads along with their corresponding anti-squeal shims and pad wear indicator plates before proceeding with the two pad support plates. These plates can be reused when free of deformation, cracks, and wear and Rust and Dirt are absent. Disk measurement results lead to placing two support pad holders correctly. Install these plates only when disc runout values pass inspection. Replace all pads with new ones as well as their corresponding anti-squeal shims and wear indicator plates during installation; users of the 2ZZ-GE engine must put a pad wear indicator on each pad and must spread grease on both sides of each inner anti-squeal shim and users of the 1ZZ-FE engine need to distribute the grease on the outside edge of the inner anti-squeal shim. After installing the two anti-squeal shims on each pad apply them in a position where the pad wear indicator plate points upward while ensuring the friction surfaces remain free of oil or grease residue. A small amount of fluid should be drawn from the reservoir before pressing the piston inward using a hammer handle or equivalent tool; when piston resistance is high loosen the bleeder plug to vent fluid while pushing in the piston. Position the caliper after keeping the sliding pin intact during installation before tightening bolts to 34 Nm (350 kgf-cm, 25 ft. lbs.). Install the front wheel before torquing it to 103 Nm (1,050 kgf-cm, 76 ft. lbs.). Then depress the brake pedal several times to check the fluid level reaches the max line.

Related Toyota Celica Parts

Browse Toyota Celica Brake Pad Set by Years

2005 2004 2003 2002 2001 2000 1999 1998 1997 1996 1995 1994 1993 1992 1991 1990 1989 1988 1987 1986 1985 1984