How to install a Power Steering Pump on Toyota Camry?

You should first install temporary bolts at the vane pump assembly before installing it. Special Service Tool: 09249-63010 should be used to tighten the 2 bolts by applying torque measurements of 29 Nm (294 kgf-cm, 21 ft-lbf) when using the tool or 43 Nm (439 kgf-cm, 32 ft-lbf) when not using it. The tool requires a torque wrench with a 300 mm (11.81 in.) fulcrum for precision. Fasten the power steering fluid pressure switch connector afterward install the new gasket to the pressure feed tube assembly before connecting it to the vane pump assembly using the union bolt with an applied torque of 50 Nm (510 kgf-cm, 37 ft-lbf). The stopper of the pressure feed tube assembly needs to maintain a secure connection with the vane pump assembly. Secure the No. 1 fluid reservoir pump hose to the vane pump assembly by installing the clip on the mark while routing the hose to the rear part of the vehicle before maximum extension. The technical procedure includes adding power steering fluid followed by fluid bleeding before checking the fluid level and searching for leaks. Installation of the fan and generator V belt comes first in this sequence. Finish the installation process by torquing the front fender apron seal RH to 103 Nm (1,050 kgf-cm, 76 ft-lbf) then connect the engine under cover RH along with the front wheel RH.

How to remove and replace the Power Steering Pump on Toyota Camry?

The first step to changing the 2AZ-FE power steering vane pump requires draining all power steering fluid. You must detach the front right wheel together with the engine under cover found on the right side together with the front fender apron seal which is also positioned on the right side. Next remove the fan together with the generator V belt. You should detach the No. 1 fluid reservoir to pump hose by moving the clip down while disconnecting it from the vane pump assembly. To disconnect the pressure feed tube assembly from the vane pump assembly you must first remove the union bolt then remove the gasket that is present on the pressure feed tube assembly. Separate the connector of the power steering fluid pressure switch. The vane pump assembly removal requires the use of Special Service Tool: 09249-63010 to first loosen two bolts before taking out the assembly together with those two bolts.

OEM Toyota Camry Power Steering Pump

Power Steering Pump Unit

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

20 Power Steering Pumps found

View related parts
Toyota Camry Power Steering Pump
Part Number: 44310-07040
$317.57 MSRP: $453.41
You Save: $135.84 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pump Assembly, Vane; Pump
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2007-2011 Toyota Camry | LE, SE, XLE | 6 Cyl 3.5 L GAS
View related parts
Toyota Camry Power Steering Pump
Part Number: 44310-06080
$333.18 MSRP: $475.70
You Save: $142.52 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pump Assembly, Vane; Pump
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2002-2006 Toyota Camry | LE, SE, XLE | 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L GAS
View related parts
Toyota Camry Power Steering Pump
Part Number: 44310-06071
$315.24 MSRP: $450.08
You Save: $134.84 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pump Assembly, Vane; Pump
- Manufacturer Note: (L)
- Replaces: 44310-06070, 44310-33150
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2002-2009 Toyota Camry | Base, CE, LE, SE, XLE | 4 Cyl 2.4 L GAS
View related parts
Toyota Camry Power Steering Pump
Part Number: 44310-06110
$340.75 MSRP: $486.52
You Save: $145.77 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pump Assembly, Vane
- Manufacturer Note: TYPE B:REFER TO ILLUSTRATION
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2002-2006 Toyota Camry | LE, SE, XLE | 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L GAS
View related parts
Toyota Camry Power Steering Pump
Part Number: 44310-33170
$307.43 MSRP: $438.94
You Save: $131.51 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pump Assembly, Vane
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2007-2011 Toyota Camry | LE, SE, XLE | 6 Cyl 3.5 L GAS
View related parts
Toyota Camry Power Steering Pump
Part Number: 44320-06030
$310.23 MSRP: $442.94
You Save: $132.71 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pump Assembly, L/Pulley; Pump Assembly, Vane
- Manufacturer Note: (L)
- Replaces: 44320-33100
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1997-2001 Toyota Camry | CE, LE, XLE | 4 Cyl 2.2 L CNG, 4 Cyl 2.2 L GAS
View related parts
Toyota Camry Power Steering Pump
Part Number: 44320-33140
$307.66 MSRP: $439.27
You Save: $131.61 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pump Assembly, L/Pulley; Pump Assembly, Vane; Pump
- Manufacturer Note: TYPE A:REFER TO ILLUSTRATION
- Replaces: 44320-33150
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2002-2006 Toyota Camry | LE, SE, XLE | 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L GAS
View related parts
Toyota Camry Power Steering Pump
Part Number: 44310-06190
$367.05 MSRP: $537.91
You Save: $170.86 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pump Assembly, Vane; Pump
- Manufacturer Note: (L)
- Replaces: 44310-33190
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2010-2011 Toyota Camry | Base, LE, SE, XLE | 4 Cyl 2.5 L GAS
View related parts
Toyota Camry Pump Assembly, Vane
Part Number: 44320-07012
$299.96 MSRP: $428.28
You Save: $128.32 (30%)
Product Specifications
- Other Name: Pump Assembly, L/Pulley; Power Steering Pump
- Manufacturer Note: (L)
- Replaces: 44320-33110, 44320-33111, 44320-07010, 44320-07011
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1995-2003 Toyota Camry | CE, LE, SE, XLE | 6 Cyl 3.0 L GAS
View related parts
Toyota Camry Power Steering Pump
Part Number: 44320-16221
Product Specifications
- Other Name: Pump Assembly, L/Pulley; Pump Assembly, Vane; Pump
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1992-1994 Toyota Camry | DLX, DX, LE, SE, XLE | 4 Cyl 2.2 L GAS, 6 Cyl 3.0 L GAS
View related parts
Toyota Camry Power Steering Pump
Part Number: 44320-32121
Product Specifications
- Other Name: Pump Assembly, L/Pulley; Pump Assembly, Vane
- Replaces: 44320-32120
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1989 Toyota Camry | DLX, LE | 6 Cyl 2.5 L GAS
View related parts
Toyota Camry Power Steering Pump
Part Number: 44320-12053
Product Specifications
- Other Name: Pump Assembly, L/Pulley
- Replaces: 44320-12051, 44320-12052, 44320-12050
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1984-1986 Toyota Camry | DLX | 4 Cyl 1.8 L DIESEL, 4 Cyl 2.0 L DIESEL
View related parts
Toyota Camry Power Steering Pump
Part Number: 44320-32013
Product Specifications
- Other Name: Pump Assembly, L/Pulley; Pump Assembly, Vane
- Replaces: 44320-32011, 44320-32012
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1984-1986 Toyota Camry | DLX, LE | 4 Cyl 1.8 L DIESEL, 4 Cyl 2.0 L DIESEL, 4 Cyl 2.0 L GAS
View related parts
Toyota Camry Power Steering Pump
Part Number: 44320-33060
Product Specifications
- Other Name: Pump Assembly, L/Pulley; Pump Assembly, Vane
- Replaces: 44320-33071, 44320-06020, 44320-06010, 44320-06011
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1992-1996 Toyota Camry | DLX, DX, LE, SE, XLE | 4 Cyl 2.2 L GAS
View related parts
Toyota Camry Power Steering Pump
Part Number: 44320-33040
Product Specifications
- Other Name: Pump Assembly, L/Pulley; Pump Assembly, Vane
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1992-1993 Toyota Camry | DLX, DX, LE, SE, XLE | 4 Cyl 2.2 L GAS
View related parts
Toyota Camry Power Steering Pump
Part Number: 44320-16201
Product Specifications
- Other Name: Pump Assembly, L/Pulley; Pump Assembly, Vane
- Replaces: 44320-16200
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1991-1994 Toyota Camry | Base, DLX, DLX All Trac, DX, LE, LE All Trac, SE, XLE | 4 Cyl 2.0 L GAS, 4 Cyl 2.2 L GAS, 6 Cyl 2.5 L GAS, 6 Cyl 3.0 L GAS
View related parts
Toyota Camry Power Steering Pump
Part Number: 44320-32140
Product Specifications
- Other Name: Pump Assembly, L/Pulley; Pump Assembly, Vane
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1988-1991 Toyota Camry | DLX, LE | 6 Cyl 2.5 L GAS
View related parts
Toyota Camry Power Steering Pump
Part Number: 44320-33080
Product Specifications
- Other Name: Pump Assembly, L/Pulley; Pump Assembly, Vane
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1994 Toyota Camry | LE, SE, XLE | 6 Cyl 3.0 L GAS
View related parts
Toyota Camry Power Steering Pump
Part Number: 44320-33010
Product Specifications
- Other Name: Pump Assembly, L/Pulley; Pump Assembly, Vane; Pump
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1992-1993 Toyota Camry | DLX, DX, LE, SE, XLE | 6 Cyl 3.0 L GAS
View related parts
Toyota Camry Power Steering Pump
Part Number: 44320-32041
Product Specifications
- Other Name: Pump Assembly, L/Pulley
- Replaces: 44320-32090, 44320-32091, 44320-32040
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1987-1991 Toyota Camry | Base, DLX, DLX All Trac, LE, LE All Trac | 4 Cyl 2.0 L GAS

Toyota Camry Power Steering Pump

Choose genuine Power Steering Pump that pass strict quality control tests. You can trust the top quality and lasting durability. Shopping for OEM Power Steering Pump for your Toyota Camry? Our website is your one-stop destination. We stock an extensive selection of genuine Toyota Camry parts. The price is affordable so you can save more. It only takes minutes to browse and find the exact fit. Easily add to cart and check out fast. Our hassle-free return policy will keep you stress-free. We process orders quickly for swift delivery. Your parts will arrive faster, so you can get back on the road sooner.

Power Steering Pump in used Toyota Camry automobiles is an essential part that translates the energy from the car's engine into hydraulic that helps the driver steers. Through supplying the hydraulic pressure to the steering system, the pump cuts the amount of force required to rotate the steering wheel and manipulate the car. Toyota Camry Power Steering Pumps generally works with the help of V-belt or serpentine belt which is provided for the preliminary engagement of the pump while the PSU possesses a fluid reservoir that might be installed either internally or externally. The pump focuses the fluid pressure on the control valve and uses forces in the direction of the turn when the steering wheel is turned. The typical power steering pump problems could include leakage, noisy pump, absence of power boost, and over-sensitive steering, for which the premier way is to change or rebuild the pump. All in all, this paper has established that the Power Steering Pump is instrumental in improving the driver's control and comfort within the Toyota Camry range through a decrease in the force required to operate the steering wheel.

Toyota Camry Power Steering Pump Parts and Q&A

Power Steering Pump
44310-06071
Q: How to install a Power Steering Pump on Toyota Camry?
A:
You should first install temporary bolts at the vane pump assembly before installing it. Special Service Tool: 09249-63010 should be used to tighten the 2 bolts by applying torque measurements of 29 Nm (294 kgf-cm, 21 ft-lbf) when using the tool or 43 Nm (439 kgf-cm, 32 ft-lbf) when not using it. The tool requires a torque wrench with a 300 mm (11.81 in.) fulcrum for precision. Fasten the power steering fluid pressure switch connector afterward install the new gasket to the pressure feed tube assembly before connecting it to the vane pump assembly using the union bolt with an applied torque of 50 Nm (510 kgf-cm, 37 ft-lbf). The stopper of the pressure feed tube assembly needs to maintain a secure connection with the vane pump assembly. Secure the No. 1 fluid reservoir pump hose to the vane pump assembly by installing the clip on the mark while routing the hose to the rear part of the vehicle before maximum extension. The technical procedure includes adding power steering fluid followed by fluid bleeding before checking the fluid level and searching for leaks. Installation of the fan and generator V belt comes first in this sequence. Finish the installation process by torquing the front fender apron seal RH to 103 Nm (1,050 kgf-cm, 76 ft-lbf) then connect the engine under cover RH along with the front wheel RH.
Power Steering Pump
44310-33170
Q: How to remove and replace the Power Steering Pump on Toyota Camry?
A:
The first step to changing the 2AZ-FE power steering vane pump requires draining all power steering fluid. You must detach the front right wheel together with the engine under cover found on the right side together with the front fender apron seal which is also positioned on the right side. Next remove the fan together with the generator V belt. You should detach the No. 1 fluid reservoir to pump hose by moving the clip down while disconnecting it from the vane pump assembly. To disconnect the pressure feed tube assembly from the vane pump assembly you must first remove the union bolt then remove the gasket that is present on the pressure feed tube assembly. Separate the connector of the power steering fluid pressure switch. The vane pump assembly removal requires the use of Special Service Tool: 09249-63010 to first loosen two bolts before taking out the assembly together with those two bolts.