How to remove the power door lock actuator on 2009 Toyota Venza?

The process to remove the power door lock actuator begins with disconnecting the battery cable from the negative terminal followed by a minimum 90-second timeout of the SRS system before continuing. Post-reconnection some systems require system initialization. The first step involves changing the front door inside handle bezel plug followed by a procedure to replace the power window regulator master switch assembly with front door armrest base panel from the driver side along with a similar procedure for the front passenger side. The maintenance process will begin with removal of the front door inside handle sub-assembly and the courtesy light assembly before proceeding to take away the front door trim board sub-assembly and the front door inside handle sub-assembly. The technician must remove the door side Air Bag sensor followed by the front door service hole cover before disconnecting the front door glass sub-assembly leading to removal of front door glass run and front door rear lower frame sub-assembly. Lift off the front door outside handle cover together with the lock cylinder assembly before breaking the front door lock assembly connector. A T30 "TORX" socket wrench will help you remove the 3 screws from the front door lock assembly while allowing you to pull down the assembly and withdraw it and its cables as an integrated unit. Sever the seal on the wire harness for the door lock and detach the remote control cable assembly from the front door lock assembly by dislodging 3 claws with a screwdriver that is taped to protect the tip. The front door inside locking cable assembly should be taken off from the front door lock assembly.

OEM 2009 Toyota Venza Door Lock Actuator

Power Door Lock Actuator

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

6 Door Lock Actuators found

View related parts
2009 Toyota Venza Gate Lock, Rear
Part Number: 69350-0E100
$335.28 MSRP: $478.70
You Save: $143.42 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Lock Assembly, Back Door; Liftgate Latch; Tailgate Lock Actuator; Trunk Lock Actuator; Door Lock Actuator; Lock Actuator; Lock Assembly; Lock Assembly, Back Door, W/Courtesy Lamp Switch
- Position: Rear
- Replaces: 69350-0T010
- Part Name Code: 69350P
- Item Weight: 2.40 Pounds
- Item Dimensions: 12.2 x 9.5 x 4.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 69350-0E100
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2009 Toyota Venza Submodels:
- Base, LE, Limited, XLE | 4 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS
View related parts
2009 Toyota Venza Lock Actuator, Driver Side
Part Number: 69040-0C050
$254.66 MSRP: $363.60
You Save: $108.94 (30%)
ADD TO CART
Product Specifications
- Other Name: Lock Assembly, Front Door W; Door Lock Actuator Motor, Front Left; Door Latch Assembly, Front Left; Lock Assembly; Front Door W/Motor, Driver Side; Door Lock Actuator Motor.
- Position: Driver Side
- Replaces: 69040-06180
- Item Weight: 2.10 Pounds
- Item Dimensions: 8.5 x 5.7 x 5.7 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 69040-0C050
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2009 Toyota Venza Submodels:
- Base, LE, Limited, XLE | 4 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS
View related parts
2009 Toyota Venza Lock Assembly, Front Door W/Motor, Passenger Side
Part Number: 69030-0C050
$248.02 MSRP: $354.11
You Save: $106.09 (30%)
ADD TO CART
Product Specifications
- Other Name: Lock Assembly, Front Door W; Passenger Side; Door Lock Actuator Motor; Actuator; Lock
- Position: Passenger Side
- Replaces: 69030-06200
- Item Weight: 1.90 Pounds
- Item Dimensions: 8.2 x 5.7 x 5.7 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 69030-0C050
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2009 Toyota Venza Submodels:
- Base, LE, Limited, XLE | 4 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS
View related parts
2009 Toyota Venza Lock Actuator, Driver Side
Part Number: 69060-06100
$253.96 MSRP: $362.60
You Save: $108.64 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Lock Assembly, Rear Door W; Door Lock Actuator Motor, Rear Left; Door Latch Assembly, Rear Left; Lock Assembly; Rear Door W/Motor, Driver Side; Door Lock Actuator Motor.
- Position: Driver Side
- Replaces: 69060-33120
- Part Name Code: 69060A
- Item Weight: 0.60 Pounds
- Item Dimensions: 8.4 x 5.8 x 5.9 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 69060-06100
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2009 Toyota Venza Submodels:
- Base, LE, Limited, XLE | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS
View related parts
2009 Toyota Venza Lock Actuator, Passenger Side
Part Number: 69050-06100
$248.02 MSRP: $354.11
You Save: $106.09 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Lock Assembly, Rear Door W; Door Lock Actuator Motor, Rear Right; Door Latch Assembly, Rear Right; Lock Assembly; Rear Door W/Motor, Passenger Side; Door Lock Actuator Motor.
- Position: Passenger Side
- Replaces: 69050-33120
- Part Name Code: 69050A
- Item Weight: 0.60 Pounds
- Item Dimensions: 8.2 x 5.8 x 5.7 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 69050-06100
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2009 Toyota Venza Submodels:
- Base, LE, Limited, XLE | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS
View related parts
2009 Toyota Venza Lock Actuator, Rear
Part Number: 69350-0T030
$357.17 MSRP: $523.44
You Save: $166.27 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Lock Assembly, Back Door; Liftgate Latch; Tailgate Lock Actuator; Trunk Lock Actuator; Door Lock Actuator; Lock Assembly; Lock Assembly, Back Door, W/Courtesy Lamp Switch
- Position: Rear
- Part Name Code: 69350P
- Item Weight: 2.40 Pounds
- Item Dimensions: 16.5 x 12.1 x 3.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 69350-0T030
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2009 Toyota Venza Submodels:
- Base, LE, Limited, XLE | 4 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS

2009 Toyota Venza Door Lock Actuator

Looking for affordable OEM 2009 Toyota Venza Door Lock Actuator? Explore our comprehensive catalogue of genuine 2009 Toyota Venza Door Lock Actuator. All our parts are covered by the manufacturer's warranty. Plus, our straightforward return policy and speedy delivery service ensure an unparalleled shopping experience. We look forward to your visit!

2009 Toyota Venza Parts Questions & Experts Answers

Q: How to remove the power door lock actuator on 2009 Toyota Venza?
A: The process to remove the power door lock actuator begins with disconnecting the battery cable from the negative terminal followed by a minimum 90-second timeout of the SRS system before continuing. Post-reconnection some systems require system initialization. The first step involves changing the front door inside handle bezel plug followed by a procedure to replace the power window regulator master switch assembly with front door armrest base panel from the driver side along with a similar procedure for the front passenger side. The maintenance process will begin with removal of the front door inside handle sub-assembly and the courtesy light assembly before proceeding to take away the front door trim board sub-assembly and the front door inside handle sub-assembly. The technician must remove the door side Air Bag sensor followed by the front door service hole cover before disconnecting the front door glass sub-assembly leading to removal of front door glass run and front door rear lower frame sub-assembly. Lift off the front door outside handle cover together with the lock cylinder assembly before breaking the front door lock assembly connector. A T30 "TORX" socket wrench will help you remove the 3 screws from the front door lock assembly while allowing you to pull down the assembly and withdraw it and its cables as an integrated unit. Sever the seal on the wire harness for the door lock and detach the remote control cable assembly from the front door lock assembly by dislodging 3 claws with a screwdriver that is taped to protect the tip. The front door inside locking cable assembly should be taken off from the front door lock assembly.