How to remove and replace the ABS Control Module for Antilock Brakes on 2009 Toyota Sequoia?

The first step to replace or remove the Hydraulic Control Assembly for Antilock Brakes requires pulling off the VSC actuator connector with its release bar to prevent brake fluid leakage. Mark the reconnection points for brake tubes and then detach the 2 brake tubes from both ends using a 10 mm union nut wrench. Extract both tubes from their locations at the VSC actuator and brake master cylinder. Use a union nut wrench of 10 mm to disconnect the 4 brake tubes that attach to the VSC actuator step by step then remove the clamp from the VSC actuator mounting bracket. The end of this procedure requires users to disconnect the VSC actuator with actuator bracket assembly by removing 3 nuts while being cautious to protect brake lines along with the wire harness.

OEM 2009 Toyota Sequoia ABS Control Module

Anti Lock Brake Control Module

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

2 ABS Control Modules found

View related parts
2009 Toyota Sequoia Modulator Valve
Part Number: 44050-0C212
$1063.71 MSRP: $1339.01
You Save: $275.30 (21%)
ADD TO CART
Product Specifications
- Other Name: Actuator Assembly, Brake; ABS Hydraulic Assembly; ABS Pump And Motor Assembly; ABS Control Module; Actuator Assembly
- Manufacturer Note: REAR SUSPENSION-AIR SUSPENSION
- Replaces: 44050-0C211
- Part Name Code: 44510
- Item Weight: 4.90 Pounds
- Item Dimensions: 9.2 x 7.6 x 6.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 44050-0C212
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2009 Toyota Sequoia Submodels:
- Limited, Platinum, SR5 | 8 Cyl 4.6 L GAS, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L FLEX, 8 Cyl 5.7 L GAS
View related parts
2009 Toyota Sequoia Modulator Valve
Part Number: 44050-0C202
$986.64 MSRP: $1242.00
You Save: $255.36 (21%)
Product Specifications
- Other Name: Actuator Assembly, Brake; ABS Hydraulic Assembly; ABS Pump And Motor Assembly; ABS Control Module; Actuator Assembly
- Replaces: 44050-0C200
- Part Name Code: 44510
- Item Weight: 5.00 Pounds
- Item Dimensions: 9.0 x 7.9 x 6.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 44050-0C202
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2009 Toyota Sequoia Submodels:
- Limited, Platinum, SR5 | 8 Cyl 4.6 L GAS, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L FLEX, 8 Cyl 5.7 L GAS

2009 Toyota Sequoia ABS Control Module

Looking for affordable OEM 2009 Toyota Sequoia ABS Control Module? Explore our comprehensive catalogue of genuine 2009 Toyota Sequoia ABS Control Module. All our parts are covered by the manufacturer's warranty. Plus, our straightforward return policy and speedy delivery service ensure an unparalleled shopping experience. We look forward to your visit!

2009 Toyota Sequoia ABS Control Module Parts Q&A

Q: How to remove and replace the ABS Control Module for Antilock Brakes on 2009 Toyota Sequoia?
A: The first step to replace or remove the Hydraulic Control Assembly for Antilock Brakes requires pulling off the VSC actuator connector with its release bar to prevent brake fluid leakage. Mark the reconnection points for brake tubes and then detach the 2 brake tubes from both ends using a 10 mm union nut wrench. Extract both tubes from their locations at the VSC actuator and brake master cylinder. Use a union nut wrench of 10 mm to disconnect the 4 brake tubes that attach to the VSC actuator step by step then remove the clamp from the VSC actuator mounting bracket. The end of this procedure requires users to disconnect the VSC actuator with actuator bracket assembly by removing 3 nuts while being cautious to protect brake lines along with the wire harness.

Alternate Year Models

2008 Toyota Sequoia ABS Control Module 2010 Toyota Sequoia ABS Control Module