How do you overhaul the front shock absorber with coil spring on 2005 Toyota Corolla?

Question

Accepted Answer

The overhaul procedure for the front shock absorber with coil spring starts with unmounting the front wheel along with front stabilizer link assy LH disconnection through nut removal but if ball joint rotation happens with this step then use a hexagon (6 mm) wrench on the stud to prevent this movement. Begin by disconnecting the front flexible hose while taking out the bolt to separate front flexible hose No.1 and speed sensor front LH (if ABS equipped) or just remove the front flexible hose if no ABS is present. Extract the front shock absorber with coil spring through the removal of 2 bolts and nuts from its lower sides and 3 nuts from its upper side on the shock absorber assy front LH. Fasten the front shock absorber with coil spring by attaching 2 nuts and a bolt to the bracket at the lower side while maintaining it in a vise position. To remove the front suspension support dust cover LH, utilize Special Service Tool: 09727-30021 along with the correct procedure for compressing the front coil spring LH but refrain from using an impact wrench to protect the tool from damage. Controller 09729-22031 operates on the front coil spring seat upper LH to remove its supporting nut before extracting the assembly that comprises of front suspension support sub-assy LH, front suspension support LH dust seal, front coil spring seat upper LH, front coil spring insulator upper LH, front coil spring LH, front spring bumper LH, and front coil spring insulator lower LH. The shock absorber requires inspection by compressing and extending its rod for signs of irregular resistance or untypical sounds before replacement if problems are detected. The shock absorber installation process starts with placing the front coil spring insulator lower LH onto the shock absorber before adding the front spring bumper LH on top of the piston rod. Install the front coil spring LH while holding it with Special Service Tool: 09727-30021 then place it on the shock absorber such that the lower end reaches the spring lower seat gap. You should first place the front coil spring insulator upper LH onto the system before adding the front coil spring seat upper LH with its mark positioned outward, following it with the front suspension support LH dust seal and front suspension support sub-assy LH. The front coil spring seat upper LH must be held by Special Service Tool: 09729-22031 before installing a new nut at 47 Nm (479 kgf-cm, 35 ft. lbs.) torque. Remove the tool before installing the front suspension support dust cover LH while applying MP grease No.2 into the suspension support sub-assy LH without touching the rubber surface of the upper support. The front shock absorber needs installation with coil spring while using 2 bolts and 3 nuts to create torques of 39 Nm (398 kgf-cm, 29 ft. lbs.) and 153 Nm (1,560 kgf-cm, 113 ft. lbs.). Ensure to stop the bolt from rotation as you torque the nut. The front flexible hose and speed sensor front LH must be installed at a 29 Nm (296 kgf-cm, 21 ft. lbs.) torque when ABD is present or only the hose by itself without the sensor when ABD is not present. Use a hexagon wrench (6 mm) to stabilize the ball joint stud during installation of the front stabilizer link assy LH with appropriate torque of 74 Nm (755 kgf-cm, 55 ft. lbs.). The front tire installation should be completed by tightening it to 103 Nm (1,050 kgf-cm, 76 ft. lbs.) while performing a front wheel alignment check and adjustment.

OEM 2005 Toyota Corolla Coil Springs

8 Coil Springs found

2005 Toyota Corolla Coil Spring, Front

2005 Toyota Corolla Coil Spring, Rear

2005 Toyota Corolla Coil Spring, Rear

2005 Toyota Corolla Coil Spring, Rear

2005 Toyota Corolla Coil Spring, Front

2005 Toyota Corolla Coil Spring, Front

2005 Toyota Corolla Coil Spring, Front

2005 Toyota Corolla Spring, Rear

2005 Toyota Corolla Coil Springs

2005 Toyota Corolla Parts Questions & Experts Answers

Related 2005 Toyota Corolla Parts

Alternate Year Models