Other Name: Belt Assembly, Rear Seat; Seat Belt Lap and Shoulder Belt, Rear Left; Belt & Retractor; Belt Assembly, Rear Seat 3 Point Type, Outer Driver Side
Manufacturer Note: BLACK,TRIM9#
Position: Outer Driver Side
Replaces: 73370-52031-C0
Part Name Code: 73370
Item Weight: 1.40 Pounds
Condition: New
Fitment Type: Direct Replacement
SKU: 73370-52032-C0
Warranty: This genuine part is guaranteed by Toyota's
factory warranty.
Other Name: Belt Assembly, Rear Seat; Seat Belt Lap and Shoulder Belt, Rear Right; Belt & Retractor; Belt Assembly, Rear Seat 3 Point Type, Outer Passenger Side
Manufacturer Note: BLACK,TRIM9#
Position: Outer Passenger Side
Replaces: 73360-52031-C0
Part Name Code: 73360
Item Weight: 2.30 Pounds
Item Dimensions: 12.4 x 11.1 x 8.4 inches
Condition: New
Fitment Type: Direct Replacement
SKU: 73360-52032-C0
Warranty: This genuine part is guaranteed by Toyota's
factory warranty.
Other Name: Belt Assembly, Front Seat; Seat Belt Receptacle, Front Left; Latch; Belt Assembly, Front Seat Inner, Driver Side
Manufacturer Note: DK.GRAY,TRIM9#
Position: Driver Side
Part Name Code: 73240
Item Weight: 1.10 Pounds
Condition: New
Fitment Type: Direct Replacement
SKU: 73230-52370-B0
Warranty: This genuine part is guaranteed by Toyota's
factory warranty.
More Info
Fits the following 2005 Scion xB Submodels:
Base | 4 Cyl 1.5 L GAS
2005 Scion xB Seat Belt
Looking for affordable OEM 2005 Scion xB Seat Belt? Explore our comprehensive catalogue of genuine 2005 Scion xB Seat Belt. All our parts are covered by the manufacturer's warranty. Plus, our straightforward return policy and speedy delivery service ensure an unparalleled shopping experience. We look forward to your visit!
2005 Scion xB Seat Belt Parts Q&A
Q: How to replace the rear seat belt on 2005 Scion xB?
A: The complete procedure for rear seat belt replacement includes first taking out the rear door scuff plate RH, rear door opening trim RH, deck board No.1, deck board No.2, deck floor box LH, deck floor box RH, rear seat assembly, back door Weather Strip, deck trim cover rear, deck trim side panel assembly RH, and roof side garnish inner RH. Detach the rear seat 3 point type belt assembly outer by first removing the bolt and seat belt from the shoulder anchor and then removing the bolt from the retractor to disconnect it entirely. The rear seat belt assembly outer center requires the removal of seatback board and shoulder belt cover and floor anchor bolt and its connected belt assembly before unfastening the retractor side bolt and nut. Detach the rear seat inner w/center belt assembly RH and LH by unfastening its bolt and inner belt. The removal and installation process of the child restraint seat anchor bracket sub-assembly RH requires 4 bolt removal to detach the anchor bracket and bracket installation with 4 torqued bolts to 42 Nm (430 kgf.cm, 31 ft.lbf). Install the rear seat inner w/center belt assembly LH and RH by fastening the floor anchor and belt using the bolt at 42 Nm (430 kgf.cm, 31 ft.lbf) torque but avoiding contact of the anchor part to the floor panel protrusions. To install the belt on the rear seat belt assembly outer center retractor side use the nut followed by torque application to 42 Nm (430 kgf.cm, 31 ft.lbf). The ELR lock function should be checked by verifying proper locking behavior at over 45 degrees of tilt yet maintaining an unlocked state during 15 degrees of tilt when gently testing the retractor movement. The technician should replace the belt assembly when the operation deviates from specified procedures. After installing the seat belt with its bolt and torquing it to 42 Nm (430 kgf.cm, 31 ft.lbf), check the ELR lock operation by pulling the belt quickly after installation at lengths shorter than 955 mm (37.60 in.). Check the child restraint system belt fastening mechanism which should allow full belt extraction but generate automatic rewind upon maximum extraction and enable belt extraction and rewinding from the fully wound state; replace the belt assembly if these operational checks reveal wrong behavior. The installation of the rear seat 3 point type belt assembly outer requires attachment with the retractor side bolt then torque to 42 Nm (430 kgf.cm, 31 ft.lbf) before checking the ELR locking mechanism to activate at over 45 degrees of tilt yet remain unlocked below 15 degrees during retractor movement. Secure and torques the belt using the 42 Nm (430 kgf.cm, 31 ft.lbf) torque setting on the floor anchor side while verifying that the anchor part remains outside the protrusion area of the floor panel. Then quickly check the ELR lock after completion. Follow instructions for verifying the belts of the child restraint system that allows full extension and rewinding after a complete pull but creates an installation failure when release and rewind functions fail. Replace the belt assembly when test results fail to match specifications. You should install the rear seat assembly as your last step.