How to service and repair the A/C Clutch on 2001 Toyota Tacoma?

Proceed with compressor and magnetic clutch service by allowing an idle engine run with active A/C for ten minutes beforeending the engine then removing battery negative cable access. The refrigeration system's refrigerant needs to be discharged before people remove the engine under cover while disconnecting the discharge and suction hoses by extracting 2 bolts. The open fittings require immediate capping to stop moisture or dirt entry. To start the compressor removal begin by removing the drive belt following the additional step of removing the power steering pump set bolt and nut for 5VZ-FE engine models before disconnecting the connector and removing 4 bolts. Secure the compressor by tighten its 4 bolts to 25 N.m (250 kgf.cm, 18 ft.lbf) while also reconnecting the connector for operation. Connect the discharge and suction hoses using 2 bolts which need to be tightened to 10 N.m (100 kgf.cm, 7 ft.lbf) but include compressor oil lubrication on new O-rings before performing installation. After checking the drive belt installation proceed with engine under cover reinstallation. The power steering pump set bolt and nut installation for 5VZ-FE engine models requires 43 N.m (440 kgf.cm, 32 ft.lbf) torque specification. Reinstall the negative (-) terminal battery cable while performing an air evacuation of the refrigeration system until it reaches its required 600 plus or minus 50 g (21.16 plus or minus 1.76 oz.) final pressure. The last step involves checking for refrigerant slippage with a gas leak detector followed by a torque check on the joints if leakage occurs before performing an A/C operation check.

OEM 2001 Toyota Tacoma A/C Clutch

Air Conditioning Clutch

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

7 A/C Clutches found

View related parts
2001 Toyota Tacoma Clutch Assembly
Part Number: 88410-34040
$144.98 MSRP: $205.24
You Save: $60.26 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Clutch Assembly, Magnet; A/C Compressor Clutch; Clutch
- Replaces: 88410-30440
- Part Name Code: 88410
- Item Weight: 16.60 Pounds
- Item Dimensions: 11.6 x 7.2 x 8.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 88410-34040
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2001 Toyota Tacoma Submodels:
- Base, DLX, Pre Runner, SR5 | 4 Cyl 2.4 L GAS, 4 Cyl 2.7 L GAS
View related parts
2001 Toyota Tacoma Clutch Assembly
Part Number: 88410-35340
$148.27 MSRP: $209.90
You Save: $61.63 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Clutch Assembly, Magnet; A/C Compressor Clutch; Clutch
- Manufacturer Note: DEALER OPTION
- Replaces: 88410-04030
- Part Name Code: 88410
- Item Weight: 4.70 Pounds
- Item Dimensions: 8.0 x 6.9 x 4.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 88410-35340
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2001 Toyota Tacoma Submodels:
- Base, DLX, Limited, Pre Runner, SR5, S-Runner | 6 Cyl 3.4 L GAS
View related parts
2001 Toyota Tacoma Clutch Coil
Part Number: 88411-02030
$138.83 MSRP: $196.53
You Save: $57.70 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Stator, Magnet Clutch; A/C Compressor Clutch Coil; Magnet; Coil; Stator Sub-Assembly, Magnet Clutch; A/C Compressor Clutch
- Replaces: 88411-2A030, 88411-22310, 88411-0C010, 88411-04010
- Part Name Code: 88302
- Item Weight: 2.00 Pounds
- Item Dimensions: 6.3 x 5.5 x 2.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 88411-02030
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2001 Toyota Tacoma Submodels:
- Base, DLX, Limited, Pre Runner, SR5, S-Runner | 4 Cyl 2.4 L GAS, 4 Cyl 2.7 L GAS, 6 Cyl 3.4 L GAS
View related parts
2001 Toyota Tacoma Clutch
Part Number: 88410-34020
$145.10 MSRP: $205.41
You Save: $60.31 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Clutch Assembly, Magnet; A/C Compressor Clutch
- Replaces: 88410-04020
- Part Name Code: 88410
- Item Weight: 5.50 Pounds
- Item Dimensions: 6.3 x 6.2 x 3.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 88410-34020
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2001 Toyota Tacoma Submodels:
- Base, DLX, Pre Runner, SR5 | 4 Cyl 2.4 L GAS, 4 Cyl 2.7 L GAS
View related parts
2001 Toyota Tacoma Rotor
Part Number: 88412-35090
$342.26 MSRP: $501.58
You Save: $159.32 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Rotor, Magnet Clutch; A/C Compressor Clutch Pulley; Rotor Sub-Assembly, Magnet Clutch; A/C Compressor Clutch
- Part Name Code: 88301
- Item Weight: 2.70 Pounds
- Item Dimensions: 5.7 x 5.4 x 2.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 88412-35090
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2001 Toyota Tacoma Submodels:
- Base, DLX, Limited, Pre Runner, SR5, S-Runner | 6 Cyl 3.4 L GAS
View related parts
2001 Toyota Tacoma Rotor
Part Number: 88412-95J00
$285.01 MSRP: $406.92
You Save: $121.91 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Rotor, Magnet Clutch; A/C Compressor Clutch Pulley; Rotor Sub-Assembly, Magnet Clutch; A/C Compressor Clutch
- Part Name Code: 88301
- Item Weight: 2.20 Pounds
- Item Dimensions: 5.9 x 5.4 x 2.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 88412-95J00
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2001 Toyota Tacoma Submodels:
- Base, DLX, Pre Runner, SR5 | 4 Cyl 2.4 L GAS, 4 Cyl 2.7 L GAS
View related parts
2001 Toyota Tacoma Hub Sub-Assembly, Magnet Clutch
Part Number: 88403-06050
Product Specifications
- Other Name: Hub Sub-Assembly, Magnet; A/C Compressor Clutch
- Replaces: 88403-30290
- Part Name Code: 88403
- Item Weight: 1.40 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 88403-06050
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2001 Toyota Tacoma Submodels:
- Base, DLX, Limited, Pre Runner, SR5, S-Runner | 4 Cyl 2.4 L GAS, 4 Cyl 2.7 L GAS, 6 Cyl 3.4 L GAS

2001 Toyota Tacoma A/C Clutch

Looking for affordable OEM 2001 Toyota Tacoma A/C Clutch? Explore our comprehensive catalogue of genuine 2001 Toyota Tacoma A/C Clutch. All our parts are covered by the manufacturer's warranty. Plus, our straightforward return policy and speedy delivery service ensure an unparalleled shopping experience. We look forward to your visit!

2001 Toyota Tacoma Parts Questions & Experts Answers

Q: How to service and repair the A/C Clutch on 2001 Toyota Tacoma?
A: Proceed with compressor and magnetic clutch service by allowing an idle engine run with active A/C for ten minutes beforeending the engine then removing battery negative cable access. The refrigeration system's refrigerant needs to be discharged before people remove the engine under cover while disconnecting the discharge and suction hoses by extracting 2 bolts. The open fittings require immediate capping to stop moisture or dirt entry. To start the compressor removal begin by removing the drive belt following the additional step of removing the power steering pump set bolt and nut for 5VZ-FE engine models before disconnecting the connector and removing 4 bolts. Secure the compressor by tighten its 4 bolts to 25 N.m (250 kgf.cm, 18 ft.lbf) while also reconnecting the connector for operation. Connect the discharge and suction hoses using 2 bolts which need to be tightened to 10 N.m (100 kgf.cm, 7 ft.lbf) but include compressor oil lubrication on new O-rings before performing installation. After checking the drive belt installation proceed with engine under cover reinstallation. The power steering pump set bolt and nut installation for 5VZ-FE engine models requires 43 N.m (440 kgf.cm, 32 ft.lbf) torque specification. Reinstall the negative (-) terminal battery cable while performing an air evacuation of the refrigeration system until it reaches its required 600 plus or minus 50 g (21.16 plus or minus 1.76 oz.) final pressure. The last step involves checking for refrigerant slippage with a gas leak detector followed by a torque check on the joints if leakage occurs before performing an A/C operation check.