How to install the throttle body with motor body assembly on Toyota Tacoma?

Place a new gasket on the intake manifold before securing the throttle with motor body through 2 bolts and 2 nuts which must reach 9 Nm (92 kgf-cm, 80 in-lbf) torque level. Secondly attach the water by-pass hose to both water by-pass hose No. 2 as well as the throttle motor connector. The intake air connector must be installed with 3 bolts that receive torque to 8 Nm (82 kgf-cm, 71 in-lbf) pressure and both hose clamp bolts should be tightened to 5 Nm (51 kgf-cm, 44 in-lbf). Suspend the vacuum hose and ventilation hose Number 2 alongside another vacuum hose while connecting the wire harness clamp with the pressure sensor connector. Replace the cable on the negative battery terminal then torque it to 3.9 Nm (40 kgf-cm, 35 in-lbf). Check for any engine coolant leaks after performing the addition of new coolant. The under cover assembly No.1 for 4WD and Pre-Runner models needs installation. After replacing the ECM or throttle body components or during throttle body cleaning operations you need to disconnect the negative battery cable before waiting 60 seconds then reconnecting it. Move the ignition switch to the ON position and refrain from using the accelerator pedal before completing the preceding steps. Repeating the entire process becomes necessary if you operate the pedal. Connect the tester at DLC3 then execute DTCs clearing procedures. The MIL should not activate and the engine speed should stay within specified limits with A/C off after heating the engine completely while all accessories are off and shift lever is set to N or P. Next, access the following menus: Powertrain / Engine and ECT / Data List / Throttle Pos. Sensor Output. Push the accelerator pedal to its maximum position. Verify that the value exceeds 60%. The conclusion of this procedure requires a drive test to detect any irregularities.

How to remove the throttle body on Toyota Tacoma?

The first step required to remove the throttle body is disconnecting the battery cable from the negative terminal. The first operation requires removal of the No. 1 engine under cover sub-assembly that belongs to 4WD and Pre-Runner models. The draining process for engine coolant must be completed before technicians can move onto disconnecting the pressure sensor connector and unclamping the wire harness while separating all 3 vacuum hoses and ventilation connectors before removing the intake air connector through three bolt removal. The procedure for removing the throttle with motor body assembly involves first disconnecting the water by-pass hose then disconnecting the No. 2 water by-pass hose before detaching the throttle motor connector and removing 2 bolts and 2 nuts to extract the throttle with motor body. You should take away the gasket that is located on the intake manifold.

OEM Toyota Tacoma Throttle Body

Fuel Injection Throttle Body

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

26 Throttle Bodies found

View related parts
Toyota Tacoma Throttle Body
Part Number: 22210-75240
$410.29 MSRP: $601.29
You Save: $191.00 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Body Assembly, Throttle
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2000-2004 Toyota Tacoma | Base, Pre Runner, SR5 | 4 Cyl 2.4 L GAS, 4 Cyl 2.7 L GAS
View related parts
Toyota Tacoma Throttle Body
Part Number: 22210-75210
$411.09 MSRP: $602.45
You Save: $191.36 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Body Assembly, Throttle
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1997-2004 Toyota Tacoma | Base, DLX, Pre Runner, SR5 | 4 Cyl 2.4 L GAS, 4 Cyl 2.7 L GAS
View related parts
Toyota Tacoma Throttle Body
Part Number: 22030-75020
$335.04 MSRP: $478.37
You Save: $143.33 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Body Assembly, Throttle; Fuel Injection Throttle Body; ETB Assembly; Body Assembly, Throttle W/Throttle Position Sensor
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2005-2015 Toyota Tacoma | Base, Pre Runner | 4 Cyl 2.7 L GAS
View related parts
Toyota Tacoma Body Assembly, Throttle W/Throttle Position Sensor
Part Number: 22030-0P060
$337.95 MSRP: $482.52
You Save: $144.57 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Body Assembly, Throttle; Fuel Injection Throttle Body Assembly; Throttle Body
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2016-2022 Toyota Tacoma | Limited, Nightshade, SR, SR5, Trail, TRD Off-Road, TRD Pro, TRD Sport | 6 Cyl 3.5 L GAS
View related parts
Toyota Tacoma Throttle Body
Part Number: 22030-0P010
$338.30 MSRP: $483.03
You Save: $144.73 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Body Assembly, Throttle; Fuel Injection Throttle Body; ETB Assembly; Body Assembly, Throttle W/Throttle Position Sensor
- Replaces: 22030-31010
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2005-2015 Toyota Tacoma | Base, Pre Runner, TRD Pro, X-Runner | 6 Cyl 4.0 L GAS
View related parts
Toyota Tacoma Throttle Body
Part Number: 22030-75040
$321.64 MSRP: $459.23
You Save: $137.59 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Body Assembly, Throttle; Body Assembly, Throttle W/Throttle Position Sensor
- Replaces: 22030-0C030
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2016-2022 Toyota Tacoma | SR, SR5 | 4 Cyl 2.7 L GAS
View related parts
Toyota Tacoma Throttle Body
Part Number: 22210-75220
Product Specifications
- Other Name: Body Assembly, Throttle
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1997-2000 Toyota Tacoma | Base, DLX, Pre Runner, SR5 | 4 Cyl 2.4 L GAS, 4 Cyl 2.7 L GAS
View related parts
Toyota Tacoma Throttle Body
Part Number: 22210-62210
Product Specifications
- Other Name: Body Assembly, Throttle
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1997-2004 Toyota Tacoma | Base, DLX, Pre Runner, SR5, S-Runner | 6 Cyl 3.4 L GAS
View related parts
Toyota Tacoma Throttle Body
Part Number: 22210-62250
Product Specifications
- Other Name: Body Assembly, Throttle
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1997-2003 Toyota Tacoma | Base, DLX, Limited, SR5 | 6 Cyl 3.4 L GAS
View related parts
Toyota Tacoma Throttle Body
Part Number: 22210-62230
Product Specifications
- Other Name: Body Assembly, Throttle
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1997-2003 Toyota Tacoma | Base, DLX, Limited, Pre Runner, SR5 | 6 Cyl 3.4 L GAS
View related parts
Toyota Tacoma Throttle Body
Part Number: 22210-75190
Product Specifications
- Other Name: Body Assembly, Throttle
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1996 Toyota Tacoma | Base | 4 Cyl 2.4 L GAS, 4 Cyl 2.7 L GAS
View related parts
Toyota Tacoma Throttle Body
Part Number: 22210-62260
Product Specifications
- Other Name: Body Assembly, Throttle
- Manufacturer Note: W(*CRC)
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1997-2004 Toyota Tacoma | Base, DLX, Limited, Pre Runner, SR5, S-Runner | 6 Cyl 3.4 L GAS
View related parts
Toyota Tacoma Throttle Body
Part Number: 22210-62220
Product Specifications
- Other Name: Body Assembly, Throttle
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1997-2004 Toyota Tacoma | Base, DLX, Limited, Pre Runner, SR5, S-Runner | 6 Cyl 3.4 L GAS
View related parts
Toyota Tacoma Throttle Body
Part Number: 22210-75130
Product Specifications
- Other Name: Body Assembly, Throttle
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2004, 1996-1997 Toyota Tacoma | Base, Pre Runner | 4 Cyl 2.4 L GAS, 4 Cyl 2.7 L GAS
View related parts
Toyota Tacoma Throttle Body
Part Number: 22210-62190
Product Specifications
- Other Name: Body Assembly, Throttle
- Manufacturer Note: W(*CRC)
- Replaces: 22210-62160
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1995-1996 Toyota Tacoma | Base, SR5 | 6 Cyl 3.4 L GAS
View related parts
Toyota Tacoma Throttle Body
Part Number: 22210-62240
Product Specifications
- Other Name: Body Assembly, Throttle
- Manufacturer Note: MARK 62240
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1998-2003 Toyota Tacoma | Base, DLX, Pre Runner, SR5, S-Runner | 6 Cyl 3.4 L GAS
View related parts
Toyota Tacoma Throttle Body
Part Number: 22210-75250
Product Specifications
- Other Name: Body Assembly, Throttle; Idle Air Control Valve; Idle Control Motor; Idle Speed Control
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2000-2004 Toyota Tacoma | Base, Pre Runner, SR5 | 4 Cyl 2.4 L GAS, 4 Cyl 2.7 L GAS
View related parts
Toyota Tacoma Throttle Body
Part Number: 22210-62150
$383.19 MSRP: $561.57
You Save: $178.38 (32%)
Product Specifications
- Other Name: Body Assembly, Throttle
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1995-1996 Toyota Tacoma | Base, SR5 | 6 Cyl 3.4 L GAS
View related parts
Toyota Tacoma Throttle Body
Part Number: 22210-62170
Product Specifications
- Other Name: Body Assembly, Throttle
- Manufacturer Note: W(CRUISE CONTROL)
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1995-1996 Toyota Tacoma | SR5 | 6 Cyl 3.4 L GAS
View related parts
Toyota Tacoma Throttle Body
Part Number: 22210-62180
Product Specifications
- Other Name: Body Assembly, Throttle
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1995-1996 Toyota Tacoma | SR5 | 6 Cyl 3.4 L GAS

| Page 1 of 2 |Next >

1-20 of 26 Results

Toyota Tacoma Throttle Body

Choose genuine Throttle Body that pass strict quality control tests. You can trust the top quality and lasting durability. Shopping for OEM Throttle Body for your Toyota Tacoma? Our website is your one-stop destination. We stock an extensive selection of genuine Toyota Tacoma parts. The price is affordable so you can save more. It only takes minutes to browse and find the exact fit. Easily add to cart and check out fast. Our hassle-free return policy will keep you stress-free. We process orders quickly for swift delivery. Your parts will arrive faster, so you can get back on the road sooner.

The Throttle Body in Toyota Tacoma, is an important component that determines the amount of air passing through the intake system having a butterfly valve control. This component is standard on fuel-injection engines and regulates the amount of air that is provided based on the accelerator pedal. A throttle body can be controlled mechanically, using a throttle cable, or electronically; for instance, with a drive-by-wire system in which an electric actuator controls the throttle. As the performance level of the car rises, there may be several or single throttle body in the car to boost the flow of the air and increase throttle power, which reflects the improvement of control and efficiency of car engine.

Toyota Tacoma Throttle Body Parts and Q&A

Throttle Body
22030-0P010
Q: How to install the throttle body with motor body assembly on Toyota Tacoma?
A:
Place a new gasket on the intake manifold before securing the throttle with motor body through 2 bolts and 2 nuts which must reach 9 Nm (92 kgf-cm, 80 in-lbf) torque level. Secondly attach the water by-pass hose to both water by-pass hose No. 2 as well as the throttle motor connector. The intake air connector must be installed with 3 bolts that receive torque to 8 Nm (82 kgf-cm, 71 in-lbf) pressure and both hose clamp bolts should be tightened to 5 Nm (51 kgf-cm, 44 in-lbf). Suspend the vacuum hose and ventilation hose Number 2 alongside another vacuum hose while connecting the wire harness clamp with the pressure sensor connector. Replace the cable on the negative battery terminal then torque it to 3.9 Nm (40 kgf-cm, 35 in-lbf). Check for any engine coolant leaks after performing the addition of new coolant. The under cover assembly No.1 for 4WD and Pre-Runner models needs installation. After replacing the ECM or throttle body components or during throttle body cleaning operations you need to disconnect the negative battery cable before waiting 60 seconds then reconnecting it. Move the ignition switch to the ON position and refrain from using the accelerator pedal before completing the preceding steps. Repeating the entire process becomes necessary if you operate the pedal. Connect the tester at DLC3 then execute DTCs clearing procedures. The MIL should not activate and the engine speed should stay within specified limits with A/C off after heating the engine completely while all accessories are off and shift lever is set to N or P. Next, access the following menus: Powertrain / Engine and ECT / Data List / Throttle Pos. Sensor Output. Push the accelerator pedal to its maximum position. Verify that the value exceeds 60%. The conclusion of this procedure requires a drive test to detect any irregularities.
Throttle Body
22030-75020
Q: How to remove the throttle body on Toyota Tacoma?
A:
The first step required to remove the throttle body is disconnecting the battery cable from the negative terminal. The first operation requires removal of the No. 1 engine under cover sub-assembly that belongs to 4WD and Pre-Runner models. The draining process for engine coolant must be completed before technicians can move onto disconnecting the pressure sensor connector and unclamping the wire harness while separating all 3 vacuum hoses and ventilation connectors before removing the intake air connector through three bolt removal. The procedure for removing the throttle with motor body assembly involves first disconnecting the water by-pass hose then disconnecting the No. 2 water by-pass hose before detaching the throttle motor connector and removing 2 bolts and 2 nuts to extract the throttle with motor body. You should take away the gasket that is located on the intake manifold.