Other Name: Shield Sub-Assembly, Fender Splash; Fender Splash Shield; Liner, Front Fender, Driver Side
Manufacturer Note: TOWING PACKAGE-5000LBS
Position: Driver Side
Warranty: This genuine part is guaranteed by Toyota's
factory warranty.
Fits the following Vehicles:
2014-2019 Toyota Highlander | Hybrid LE, Hybrid Limited, Hybrid Limited Platinum, Hybrid XLE, LE, LE Plus, Limited, Limited Platinum, SE, XLE | 6 Cyl 3.5 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.5 L GAS
Other Name: Shield Sub-Assembly, Fender Splash; Hood Seal, Front Right, Right; Fender Splash Shield; Shield Sub-Assembly, Fender Splash, Rear Passenger Side
Position: Rear Passenger Side
Replaces: 53807-48040
Warranty: This genuine part is guaranteed by Toyota's
factory warranty.
Fits the following Vehicles:
2011-2013 Toyota Highlander | Base, Hybrid, Hybrid Limited, Limited, Plus, SE | 4 Cyl 2.7 L GAS, 6 Cyl 3.5 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.5 L GAS
Other Name: Shield Sub-Assembly, Fender Splash; Fender Splash Shield, Front Right Upper; Shield Sub-Assembly, Fender Splash, Rear Passenger Side; Fender Splash Shield
Position: Rear Passenger Side
Warranty: This genuine part is guaranteed by Toyota's
factory warranty.
Fits the following Vehicles:
2020-2023 Toyota Highlander | Hybrid Bronze Edition, Hybrid LE, Hybrid Limited, Hybrid Platinum, Hybrid XLE, L, LE, Limited, Platinum, XLE, XSE | 4 Cyl 2.4 L GAS, 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.5 L GAS
Other Name: Shield Sub-Assembly, Fender Splash; Hood Seal, Front Left, Left; Fender Splash Shield; Shield Sub-Assembly, Fender Splash, Rear Driver Side
Position: Rear Driver Side
Replaces: 53808-48010
Warranty: This genuine part is guaranteed by Toyota's
factory warranty.
Fits the following Vehicles:
2008-2010 Toyota Highlander | Base, Hybrid, Hybrid Limited, Limited, SE, Sport | 4 Cyl 2.7 L GAS, 6 Cyl 3.3 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.5 L GAS
Other Name: Liner, Front Fender, Right-Hand; Fender Splash Shield, Front Right; Fender Splash Shield
Position: Front Passenger Side
Warranty: This genuine part is guaranteed by Toyota's
factory warranty.
Fits the following Vehicles:
2001-2003 Toyota Highlander | Base, Limited | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS
| Page 1 of 2 |Next >
1-20 of 33 Results
Toyota Highlander Wheelhouse
Choose genuine Wheelhouse that pass strict quality control tests. You can trust the top quality and lasting durability. Shopping for OEM Wheelhouse for your Toyota Highlander? Our website is your one-stop destination. We stock an extensive selection of genuine Toyota Highlander parts. The price is affordable so you can save more. It only takes minutes to browse and find the exact fit. Easily add to cart and check out fast. Our hassle-free return policy will keep you stress-free. We process orders quickly for swift delivery. Your parts will arrive faster, so you can get back on the road sooner.
Q: How to remove the front Wheelhouse on Toyota Highlander?
A:
The front fender liner removal starts by taking away the engine under cover assembly (for 2GR-FE) then continuing with the No. 1 engine under cover. For the removal of the front fender moulding sub-assembly the procedures are the same for both left-hand and right-hand side operations. The LH front wheel opening extension pad can be removed through screw removal of its two attachment points. The RH side requires another repetition of this process. The procedure to uninstall the front fender liner LH starts by removing the screw followed by using a screwdriver to rotate the pin 90 degrees to free the pin hold clip then using a 4 mm hexagon wrench to eliminate the 2 screws. The process to detach the front fender liner LH requires you to remove its 2 grommets and to install new ones because grommets will break upon removal while the detachment sequence concludes with 5 clips and 8 screws. To detach the front fender liner RH you should first remove the screw then rotate the pin for 90 degrees and pull off the pin hold clip after that use a 4 mm hexagon wrench to remove both screws and put the new grommets before you take apart the 5 clips and 7 screws.
Q: How to install the front Wheelhouse and related components on both the LH and RH sides on Toyota Highlander?
A:
Install the front fender liner LH by using 5 clips and 8 screws alongside 2 new grommets and securing them with a 4 mm hexagon wrench for the 2 screws and then use the screw and pin hold clip while tightening the fasteners to 3.0 Nm (31 kgf-cm, 27 in-lbf). Both front fender liners RH must be mounted with 5 clips and 7 screws and 2 new grommets and the same torque specifications should be used. The installation of the front wheel opening extension pad requires two screws on the LH side with identical procedures for the RH side. The factory should install the front fender moulding sub-assembly LH before moving on to install the front fender moulding sub-assembly RH by using identical installation methods. Place the No. 1 engine under cover and the engine under cover assembly as your conclusion.