How to install the front speed sensor on 2009 Toyota Venza?

Start by repeating the front speed sensor installation process for both left-hand (LH) and right-hand (RH) sides and then follow the next steps regarding the LH side. The front sensor rotor needs to replace at the same time when repairing the front drive shaft assembly. Fitting the resin clamp along with the front speed sensor requires applying an 8.0 Nm (82 kgf-cm, 71 in-lbf) torque on the bolt. Tightening the bolt needs to be done after the front speed sensor is properly inserted into the knuckle with no foreign matter attached to its tip. Furthermore, check for clearance and debris between the front speed sensor stay and knuckle. Begin by installing the No. 1 sensor clamp but only for brief installation which should penetrate the stopper hole with the claw. Install the front brake flexible hose together with the No. 1 sensor clamp to the shock absorber and use a bolt that requires 19 Nm (194 kgf-cm, 14 ft-lbf) torque while maintaining the front speed sensor wire harness straight and positioning the flexible hose over the sensor. Position the No. 2 sensor clamp to the body with a bolt and apply torque at 5.0 Nm (51 kgf-cm, 44 in-lbf). Then, install both clamps and connect the front speed sensor connector. Mount both the front fender liner LH and the front fender outside moulding LH. The installation process continues with attaching the front wheel using 103 Nm torque while following up with reconnecting the negative cable to the battery terminal and observing system requirements for post-reconnection procedures. The speed sensor signal needs to be tested as the final step.

OEM 2009 Toyota Venza Speed Sensor

Speed Control Sensor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

6 Speed Sensors found

View related parts
2009 Toyota Venza ABS Sensor, Rear Driver Side
Part Number: 89546-0T011
$174.12 MSRP: $246.49
You Save: $72.37 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor, Speed, Rear Left-Hand; ABS Wheel Speed Sensor, Rear Left; Rear Speed Sensor; Sensor, Speed, Rear Driver Side
- Position: Rear Driver Side
- Replaces: 89546-0T010
- Part Name Code: 89546
- Item Weight: 0.90 Pounds
- Item Dimensions: 10.0 x 6.6 x 2.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 89546-0T011
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2009 Toyota Venza Submodels:
- Base, LE, Limited, XLE | 4 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS
View related parts
2009 Toyota Venza ABS Sensor, Front Driver Side
Part Number: 89543-0T011
$174.12 MSRP: $246.49
You Save: $72.37 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor, Speed, Front Left-Hand; ABS Wheel Speed Sensor, Front Left; Front Speed Sensor; Sensor, Speed, Front Driver Side
- Position: Front Driver Side
- Replaces: 89543-0T010
- Part Name Code: 89543
- Item Weight: 0.90 Pounds
- Item Dimensions: 10.3 x 6.8 x 2.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 89543-0T011
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2009 Toyota Venza Submodels:
- Base, LE, Limited, XLE | 4 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS
View related parts
2009 Toyota Venza ABS Sensor, Front Passenger Side
Part Number: 89542-0T011
$174.12 MSRP: $246.49
You Save: $72.37 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor, Speed, Front Right-Hand; ABS Wheel Speed Sensor, Front Right; Front Speed Sensor; Sensor, Speed, Front Passenger Side
- Position: Front Passenger Side
- Replaces: 89542-0T010
- Part Name Code: 89542
- Item Weight: 0.90 Pounds
- Item Dimensions: 10.3 x 6.7 x 2.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 89542-0T011
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2009 Toyota Venza Submodels:
- Base, LE, Limited, XLE | 4 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS
View related parts
2009 Toyota Venza Vehicle Speed Sensor
Part Number: 89413-06010
$187.79 MSRP: $268.12
You Save: $80.33 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor, Transmission; Sensor, Transmission Revolution
- Manufacturer Note: (L)
- Replaces: 89413-73010
- Part Name Code: 89413B
- Item Weight: 0.60 Pounds
- Item Dimensions: 4.4 x 2.5 x 1.7 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 89413-06010
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2009 Toyota Venza Submodels:
- Base, LE, XLE | 4 Cyl 2.7 L GAS
View related parts
2009 Toyota Venza ABS Sensor, Rear Passenger Side
Part Number: 89545-0T011
$174.12 MSRP: $246.49
You Save: $72.37 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor, Speed, Rear Right-Hand; ABS Wheel Speed Sensor, Rear Right; Rear Speed Sensor; Sensor, Speed, Rear Passenger Side
- Position: Rear Passenger Side
- Replaces: 89545-0T010
- Part Name Code: 89545
- Item Weight: 0.90 Pounds
- Item Dimensions: 10.0 x 6.7 x 2.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 89545-0T011
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2009 Toyota Venza Submodels:
- Base, LE, Limited, XLE | 4 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS
View related parts
2009 Toyota Venza Sensor, Transmission Revolution
Part Number: 89413-0T010
$234.62 MSRP: $334.99
You Save: $100.37 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor, Transmission; Vehicle Speed Sensor
- Manufacturer Note: (L)
- Replaces: 89413-33030
- Part Name Code: 89413B
- Item Weight: 0.50 Pounds
- Item Dimensions: 9.7 x 6.2 x 3.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 89413-0T010
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2009 Toyota Venza Submodels:
- Base | 6 Cyl 3.5 L GAS

2009 Toyota Venza Speed Sensor

Looking for affordable OEM 2009 Toyota Venza Speed Sensor? Explore our comprehensive catalogue of genuine 2009 Toyota Venza Speed Sensor. All our parts are covered by the manufacturer's warranty. Plus, our straightforward return policy and speedy delivery service ensure an unparalleled shopping experience. We look forward to your visit!

2009 Toyota Venza Parts Questions & Experts Answers

Q: How to install the front speed sensor on 2009 Toyota Venza?
A: Start by repeating the front speed sensor installation process for both left-hand (LH) and right-hand (RH) sides and then follow the next steps regarding the LH side. The front sensor rotor needs to replace at the same time when repairing the front drive shaft assembly. Fitting the resin clamp along with the front speed sensor requires applying an 8.0 Nm (82 kgf-cm, 71 in-lbf) torque on the bolt. Tightening the bolt needs to be done after the front speed sensor is properly inserted into the knuckle with no foreign matter attached to its tip. Furthermore, check for clearance and debris between the front speed sensor stay and knuckle. Begin by installing the No. 1 sensor clamp but only for brief installation which should penetrate the stopper hole with the claw. Install the front brake flexible hose together with the No. 1 sensor clamp to the shock absorber and use a bolt that requires 19 Nm (194 kgf-cm, 14 ft-lbf) torque while maintaining the front speed sensor wire harness straight and positioning the flexible hose over the sensor. Position the No. 2 sensor clamp to the body with a bolt and apply torque at 5.0 Nm (51 kgf-cm, 44 in-lbf). Then, install both clamps and connect the front speed sensor connector. Mount both the front fender liner LH and the front fender outside moulding LH. The installation process continues with attaching the front wheel using 103 Nm torque while following up with reconnecting the negative cable to the battery terminal and observing system requirements for post-reconnection procedures. The speed sensor signal needs to be tested as the final step.