How to install the Hood Cable Assembly on 2008 Toyota Tundra?

Pass the cable into the engine room and facilitate its movement through the grommet beginning from the rear side until the cable stopper secures itself. Push the front section of the cable through the upper radiator support before fitting it to the displayed clamp positions. After aligning the hood cable with the hood lock lever you should lock the hood lock lever by using two claws for attachment. The Hood Lock Assembly installation requires MP grease on its sliding components followed by cable connection before bolting it down using two steel bolts along with one nut at 8.0 Nm (82 kgf-cm, 71 in-lbf). Install a fresh hood cap then affix the connector when operating with Theft Deterrent System equipment. The clamp should be attached to mount the Hood Lock Control Cable Cover while using a screw and a nut to lock it in place.

OEM 2008 Toyota Tundra Hood Cable

Hood Release Cable

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

5 Hood Cables found

View related parts
2008 Toyota Tundra Release Lever, Gray, Front
Part Number: 53601-0C010-B0
$42.60 MSRP: $59.30
You Save: $16.70 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Lever Sub-Assembly, Hood; Hood Release Handle, Front; Release Handle; Lever Sub-Assembly, Hood Lock Control
- Manufacturer Note: GRAY,TRIM1#
- Position: Front
- Part Name Code: 53601
- Item Weight: 0.70 Pounds
- Item Dimensions: 13.2 x 11.1 x 1.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 53601-0C010-B0
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2008 Toyota Tundra Submodels:
- Base, Limited, Platinum, SR5 | 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L FLEX, 8 Cyl 5.7 L GAS
View related parts
2008 Toyota Tundra Release Cable, Front
Part Number: 53630-0C020
$31.95 MSRP: $44.48
You Save: $12.53 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assembly, Hood Lock; Hood Release Cable, Front; Cable Assembly, Hood Lock Control; Hood Release Cable
- Position: Front
- Part Name Code: 53630
- Item Weight: 0.80 Pounds
- Item Dimensions: 13.7 x 10.8 x 1.7 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 53630-0C020
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2008 Toyota Tundra Submodels:
- Base, Limited, Platinum, SR5 | 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L FLEX, 8 Cyl 5.7 L GAS
View related parts
2008 Toyota Tundra Release Lever, Beige, Front
Part Number: 53601-0C010-E1
$42.60 MSRP: $59.30
You Save: $16.70 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Lever Sub-Assembly, Hood; Hood Release Handle, Front; Release Handle; Lever Sub-Assembly, Hood Lock Control
- Manufacturer Note: SAND BEIGE,TRIM4#
- Position: Front
- Part Name Code: 53601
- Item Weight: 0.70 Pounds
- Item Dimensions: 12.8 x 11.0 x 1.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 53601-0C010-E1
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2008 Toyota Tundra Submodels:
- Base, Limited, Platinum, SR5 | 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L FLEX, 8 Cyl 5.7 L GAS
View related parts
2008 Toyota Tundra Release Lever, Red, Front
Part Number: 53601-0C010-E0
$42.60 MSRP: $59.30
You Save: $16.70 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Lever Sub-Assembly, Hood; Hood Release Handle, Front; Release Handle; Lever Sub-Assembly, Hood Lock Control
- Position: Front
- Part Name Code: 53601
- Item Weight: 0.50 Pounds
- Item Dimensions: 12.9 x 10.9 x 1.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 53601-0C010-E0
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2008 Toyota Tundra Submodels:
- Base, Limited, Platinum, SR5 | 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L FLEX, 8 Cyl 5.7 L GAS
View related parts
2008 Toyota Tundra Release Lever, Black, Front
Part Number: 53601-0C010-C0
$42.60 MSRP: $59.30
You Save: $16.70 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Lever Sub-Assembly, Hood; Hood Release Handle, Front; Release Handle; Lever Sub-Assembly, Hood Lock Control
- Position: Front
- Part Name Code: 53601
- Item Weight: 0.70 Pounds
- Item Dimensions: 12.9 x 10.8 x 1.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 53601-0C010-C0
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2008 Toyota Tundra Submodels:
- 1794 Edition, Base, Limited, Platinum, SR, SR5, TRD Pro | 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L FLEX, 8 Cyl 5.7 L GAS

2008 Toyota Tundra Hood Cable

Looking for affordable OEM 2008 Toyota Tundra Hood Cable? Explore our comprehensive catalogue of genuine 2008 Toyota Tundra Hood Cable. All our parts are covered by the manufacturer's warranty. Plus, our straightforward return policy and speedy delivery service ensure an unparalleled shopping experience. We look forward to your visit!

2008 Toyota Tundra Parts Questions & Experts Answers

Q: How to install the Hood Cable Assembly on 2008 Toyota Tundra?
A: Pass the cable into the engine room and facilitate its movement through the grommet beginning from the rear side until the cable stopper secures itself. Push the front section of the cable through the upper radiator support before fitting it to the displayed clamp positions. After aligning the hood cable with the hood lock lever you should lock the hood lock lever by using two claws for attachment. The Hood Lock Assembly installation requires MP grease on its sliding components followed by cable connection before bolting it down using two steel bolts along with one nut at 8.0 Nm (82 kgf-cm, 71 in-lbf). Install a fresh hood cap then affix the connector when operating with Theft Deterrent System equipment. The clamp should be attached to mount the Hood Lock Control Cable Cover while using a screw and a nut to lock it in place.