How to service and repair the Drive Shaft assembly on 2006 Toyota Tacoma?

The propeller shaft assembly servicing for Access Cab and Double Cab requires initial marking of propeller shaft flange and differential flange followed by the removal of 4 nuts and 4 bolts together with 4 washers to detach the shaft. First remove the two support bearing bolts from the frame crossmember then extract the propeller shaft into the transmission with Special Service Tool: 09325-40010 to avoid leaking oil. The universal joint spider bearings require inspection for wear and axial position; replace them when the maximum limits of 0 to 0.05 mm (0 to 0.002 inch) are exceeded. The procedure to remove the spider bearing involves first marking the propeller shaft and universal joint yoke and later tapping the spider bearing gently with a brass bar to allow the removal of the 4 snap rings with needle-nose pliers. Secure the propeller shaft within a vise before using Special Service Tool: 09332-25010 to apply pressure on the spider bearing which must remain away from striking the bearing. After flange and sleeve yoke removal you can extract center support bearing assembly No. 2 by loosening its lock nut then taking out the center yoke with spacer and support bearing. Check the propeller and center bearing shaft assembly for runout which should be less than 0.6 mm (0.024 inch). Evaluate the smooth function of center support bearing assembly No. 2 during inspections. Fasten the center support bearing onto the intermediate shaft using new MP grease No. 2 on its splines and position matchmarks correctly before torquing the new nut to 182 Nm (1,850 kgf-cm, 134 ft. lbs.) and loosening it and finally retightening to 69 Nm (700 kgf-cm, 51 ft. lbs.) while performing stake operation on the lock nut. To install a new spider apply MP grease No. 2 to its components before fitting it into the flange yoke for measuring dimensions A and B to determine proper snap ring selection. Always use new snap rings with the identical thickness. Attach the spider to the yoke followed by pressing the spider bearing into the snap ring groove using Special Service Tool: 09332-25010. Afterward, add new snap rings to finish the installation. Finally, install the propeller with center bearing shaft assembly by removing the Special Service Tool from the extension housing, aligning the matchmarks, and securing the propeller shaft with 4 bolts, 4 nuts, and 4 washers at 88 Nm (899 kgf-cm, 65 ft. lbs.), provisionally install the center support bearing with 2 mounting bolts ensuring the drain hole faces downwards, adjust the center support bearing to maintain the specified intervals, and torque the bolts to 36 Nm (369 kgf-cm, 27 ft. lbs.), concluding with an inspection for transmission oil leakage.

OEM 2006 Toyota Tacoma Drive Shaft

Axle Shaft

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

17 Drive Shafts found

View related parts
2006 Toyota Tacoma Drive Shaft
Part Number: 37100-04321
$848.63 MSRP: $1243.68
You Save: $395.05 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft
- Replaces: 37100-04320
- Item Weight: 14.60 Pounds
- Item Dimensions: 33.7 x 6.8 x 5.6 inches
- Condition: New
- SKU: 37100-04321
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2006 Toyota Tacoma Submodels:
- Base, Pre Runner, X-Runner | 6 Cyl 4.0 L GAS
View related parts
2006 Toyota Tacoma Drive Shaft
Part Number: 37100-04352
$595.75 MSRP: $873.08
You Save: $277.33 (32%)
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft
- Replaces: 37100-04350, 37100-04351
- Part Name Code: 37110
- Item Weight: 46.60 Pounds
- Item Dimensions: 86.1 x 7.1 x 7.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 37100-04352
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2006 Toyota Tacoma Submodels:
- Base, Pre Runner, X-Runner | 6 Cyl 4.0 L GAS
View related parts
2006 Toyota Tacoma Drive Shaft
Part Number: 37100-04343
$924.11 MSRP: $1354.29
You Save: $430.18 (32%)
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft
- Replaces: 37100-04342, 37100-04341, 37100-04340
- Item Weight: 38.80 Pounds
- Item Dimensions: 76.2 x 7.4 x 7.1 inches
- Condition: New
- SKU: 37100-04343
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2006 Toyota Tacoma Submodels:
- Base, TRD Pro | 6 Cyl 4.0 L GAS
View related parts
2006 Toyota Tacoma Drive Shaft, Front
Part Number: 37140-04041
$293.57 MSRP: $419.14
You Save: $125.57 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft; Shaft Assembly, Propeller, Front
- Position: Front
- Replaces: 37140-04040
- Part Name Code: 37140
- Item Weight: 15.10 Pounds
- Item Dimensions: 34.7 x 6.7 x 5.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 37140-04041
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2006 Toyota Tacoma Submodels:
- Base, Pre Runner, TRD Pro, X-Runner | 6 Cyl 4.0 L GAS
View related parts
2006 Toyota Tacoma Drive Shaft
Part Number: 37100-04332
$923.77 MSRP: $1353.79
You Save: $430.02 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft
- Replaces: 37100-04330, 37100-04331
- Condition: New
- SKU: 37100-04332
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following 2006 Toyota Tacoma Submodels:
- Base, TRD Pro | 6 Cyl 4.0 L GAS
View related parts
2006 Toyota Tacoma Drive Shaft
Part Number: 37100-04282
$855.32 MSRP: $1253.49
You Save: $398.17 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft
- Replaces: 37100-04280, 37100-04281
- Item Weight: 44.00 Pounds
- Item Dimensions: 78.4 x 7.2 x 7.2 inches
- Condition: New
- SKU: 37100-04282
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2006 Toyota Tacoma Submodels:
- Base | 4 Cyl 2.7 L GAS
View related parts
2006 Toyota Tacoma Drive Shaft
Part Number: 37100-04311
$822.75 MSRP: $1205.75
You Save: $383.00 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft
- Replaces: 37100-04310
- Item Weight: 22.20 Pounds
- Item Dimensions: 84.2 x 7.1 x 7.1 inches
- Condition: New
- SKU: 37100-04311
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2006 Toyota Tacoma Submodels:
- Pre Runner | 4 Cyl 2.7 L GAS
View related parts
2006 Toyota Tacoma Drive Shaft
Part Number: 37100-04371
$620.72 MSRP: $909.68
You Save: $288.96 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft
- Replaces: 37100-04370
- Part Name Code: 37110
- Item Weight: 15.00 Pounds
- Item Dimensions: 33.7 x 6.7 x 5.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 37100-04371
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2006 Toyota Tacoma Submodels:
- X-Runner | 6 Cyl 4.0 L GAS
View related parts
2006 Toyota Tacoma Drive Shaft
Part Number: 37100-04291
$595.75 MSRP: $873.08
You Save: $277.33 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft
- Replaces: 37100-04290
- Part Name Code: 37110
- Item Weight: 15.00 Pounds
- Item Dimensions: 33.7 x 6.9 x 5.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 37100-04291
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2006 Toyota Tacoma Submodels:
- Base | 4 Cyl 2.7 L GAS
View related parts
2006 Toyota Tacoma Drive Shaft
Part Number: 37110-04172
$544.90 MSRP: $798.56
You Save: $253.66 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft
- Replaces: 37110-04170, 37110-04171
- Condition: New
- SKU: 37110-04172
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following 2006 Toyota Tacoma Submodels:
- Base | 4 Cyl 2.7 L GAS
View related parts
2006 Toyota Tacoma Drive Shaft
Part Number: 37110-04201
$458.30 MSRP: $671.65
You Save: $213.35 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft
- Replaces: 37110-04200
- Item Weight: 15.00 Pounds
- Item Dimensions: 33.7 x 6.9 x 5.4 inches
- Condition: New
- SKU: 37110-04201
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2006 Toyota Tacoma Submodels:
- Pre Runner | 4 Cyl 2.7 L GAS
View related parts
2006 Toyota Tacoma Drive Shaft
Part Number: 37110-04191
$408.70 MSRP: $598.96
You Save: $190.26 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft
- Replaces: 37110-04190
- Part Name Code: 37110
- Item Weight: 15.30 Pounds
- Item Dimensions: 33.4 x 6.7 x 5.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 37110-04191
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2006 Toyota Tacoma Submodels:
- Base | 4 Cyl 2.7 L GAS
View related parts
2006 Toyota Tacoma Drive Shaft
Part Number: 37110-04182
$396.22 MSRP: $580.66
You Save: $184.44 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft
- Replaces: 37110-04181, 37110-04180
- Part Name Code: 37110
- Item Weight: 22.00 Pounds
- Item Dimensions: 60.6 x 6.1 x 6.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 37110-04182
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2006 Toyota Tacoma Submodels:
- Base | 4 Cyl 2.7 L GAS
View related parts
2006 Toyota Tacoma Drive Shaft, Front
Part Number: 37140-04050
$319.90 MSRP: $456.74
You Save: $136.84 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft; Shaft Assembly, Propeller, Front
- Position: Front
- Part Name Code: 37140
- Item Weight: 14.90 Pounds
- Item Dimensions: 33.4 x 6.8 x 5.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 37140-04050
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2006 Toyota Tacoma Submodels:
- Base, Pre Runner, X-Runner | 4 Cyl 2.7 L GAS, 6 Cyl 4.0 L GAS
View related parts
2006 Toyota Tacoma Drive Shaft
Part Number: 37100-04363
$951.35 MSRP: $1394.20
You Save: $442.85 (32%)
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft
- Replaces: 37100-04362, 37100-04361, 37100-04360
- Item Weight: 42.10 Pounds
- Item Dimensions: 90.5 x 7.1 x 7.2 inches
- Condition: New
- SKU: 37100-04363
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2006 Toyota Tacoma Submodels:
- Base, TRD Pro | 6 Cyl 4.0 L GAS
View related parts
2006 Toyota Tacoma Drive Shaft
Part Number: 37100-04382
$615.50 MSRP: $902.02
You Save: $286.52 (32%)
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft
- Replaces: 37100-04381, 37100-04380
- Part Name Code: 37110
- Item Weight: 93.50 Pounds
- Item Dimensions: 97.9 x 10.4 x 10.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 37100-04382
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2006 Toyota Tacoma Submodels:
- Base, Pre Runner, X-Runner | 6 Cyl 4.0 L GAS
View related parts
2006 Toyota Tacoma Drive Shaft
Part Number: 37100-04302
$640.36 MSRP: $938.45
You Save: $298.09 (32%)
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft
- Replaces: 37100-04300, 37100-04301
- Part Name Code: 37110
- Item Weight: 49.10 Pounds
- Item Dimensions: 82.4 x 8.3 x 8.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 37100-04302
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2006 Toyota Tacoma Submodels:
- Base | 4 Cyl 2.7 L GAS

2006 Toyota Tacoma Drive Shaft

Looking for affordable OEM 2006 Toyota Tacoma Drive Shaft? Explore our comprehensive catalogue of genuine 2006 Toyota Tacoma Drive Shaft. All our parts are covered by the manufacturer's warranty. Plus, our straightforward return policy and speedy delivery service ensure an unparalleled shopping experience. We look forward to your visit!

2006 Toyota Tacoma Drive Shaft Parts Q&A

Q: How to service and repair the Drive Shaft assembly on 2006 Toyota Tacoma?
A: The propeller shaft assembly servicing for Access Cab and Double Cab requires initial marking of propeller shaft flange and differential flange followed by the removal of 4 nuts and 4 bolts together with 4 washers to detach the shaft. First remove the two support bearing bolts from the frame crossmember then extract the propeller shaft into the transmission with Special Service Tool: 09325-40010 to avoid leaking oil. The universal joint spider bearings require inspection for wear and axial position; replace them when the maximum limits of 0 to 0.05 mm (0 to 0.002 inch) are exceeded. The procedure to remove the spider bearing involves first marking the propeller shaft and universal joint yoke and later tapping the spider bearing gently with a brass bar to allow the removal of the 4 snap rings with needle-nose pliers. Secure the propeller shaft within a vise before using Special Service Tool: 09332-25010 to apply pressure on the spider bearing which must remain away from striking the bearing. After flange and sleeve yoke removal you can extract center support bearing assembly No. 2 by loosening its lock nut then taking out the center yoke with spacer and support bearing. Check the propeller and center bearing shaft assembly for runout which should be less than 0.6 mm (0.024 inch). Evaluate the smooth function of center support bearing assembly No. 2 during inspections. Fasten the center support bearing onto the intermediate shaft using new MP grease No. 2 on its splines and position matchmarks correctly before torquing the new nut to 182 Nm (1,850 kgf-cm, 134 ft. lbs.) and loosening it and finally retightening to 69 Nm (700 kgf-cm, 51 ft. lbs.) while performing stake operation on the lock nut. To install a new spider apply MP grease No. 2 to its components before fitting it into the flange yoke for measuring dimensions A and B to determine proper snap ring selection. Always use new snap rings with the identical thickness. Attach the spider to the yoke followed by pressing the spider bearing into the snap ring groove using Special Service Tool: 09332-25010. Afterward, add new snap rings to finish the installation. Finally, install the propeller with center bearing shaft assembly by removing the Special Service Tool from the extension housing, aligning the matchmarks, and securing the propeller shaft with 4 bolts, 4 nuts, and 4 washers at 88 Nm (899 kgf-cm, 65 ft. lbs.), provisionally install the center support bearing with 2 mounting bolts ensuring the drain hole faces downwards, adjust the center support bearing to maintain the specified intervals, and torque the bolts to 36 Nm (369 kgf-cm, 27 ft. lbs.), concluding with an inspection for transmission oil leakage.

Alternate Year Models

2005 Toyota Tacoma Drive Shaft 2007 Toyota Tacoma Drive Shaft