How to service and repair the Drive Shaft on 2005 Toyota Tacoma?

The first step of servicing and repairing the rear propeller with center bearing shaft assembly in 2WD Access Cab and Double Cab types requires you to mark the propeller shaft flange and differential flange before you remove 4 nuts, 4 bolts and 4 washers to detach the propeller shaft. The first step includes removing the frame crossmember's 2 center support bearing bolts then pulling out the propeller shaft while inserting Special Service Tool: 09325-40010 into the transmission to stop oil leakage. The inspection of the propeller shaft universal joint spider bearing should include checks for wear and damage. Maximum axial play measurement must stay between 0 to 0.05 mm (0 to 0.002 inch). Replacement of the bearing is required if any failure issues occur. Follow these steps to extract the spider bearing by marking the propeller shaft then universal joint yoke followed by brass bar tapping before using needle nose pliers to uninstall the 4 snap rings. Special Service Tool: 09332-25010 should be used to push out the spider bearing from the propeller shaft while the shaft stays in a vise clamp position to avoid striking the shaft tube. Insert the removed spider bearings onto the spider before forcing it out of the yoke using the previous special tool. Besides checking for .6mm (0.024inch) maximum runout on the propeller with center bearing shaft assembly; perform another runout test on the propeller shaft. Procedure for center support bearing assembly No.1 includes fixing the yoke in a vice followed by chisel use to loosen lock nuts and then marking yoke and shaft before removing the center yoke, spacer, and center support bearing. Visual inspection of the center bearing must be done for normal function which includes a replacement if found defective. Place center support bearing assembly No.1 on the intermediate shaft before coating its splines with MP grease No.2 and positioning the matchmarks correctly to install the spacer. Place the yoke in a vice before installing the bearing with a new lock nut to 182 Nm (1,850 kgf-cm, 134 ft. lbs.) torque which should be followed by loosening then re-torquing to 69 Nm (700 kgf-cm, 51 ft. lbs.) before staking the lock nut last. To install the propeller shaft universal joint spider bearing start by applying MP grease No.2 to fresh components then inserting the spider into the flange yoke followed by measuring dimensions A and B for snap ring selection and pressing the spider bearing into the snap ring groove using Special Service Tool: 09332-25010. Next apply new snap rings to the grooves before evaluating the spider bearings for dimensional wear and their axial position. After removing the special service tool from the extension housing the propeller shaft assembly can be installed while keeping the matchmarks aligned and fastening it with 4 bolts, 4 nuts and 4 washers that must reach a torque of 88 Nm (899 kgf-cm, 65 ft. lbs.). Install center support bearing number one provisionally with two mounting bolts while directing the drain hole towards the bottom and adjust the bearing to sit between 0 and 1.0 mm (0 and 0.039 inch) of center line during unladen condition before tightening the bolts to 36 Nm (369 kgf-cm, 27 ft. lbs.). Check for transmission oil leaks after procedure completion.

OEM 2005 Toyota Tacoma Drive Shaft

Axle Shaft

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

17 Drive Shafts found

View related parts
2005 Toyota Tacoma Drive Shaft
Part Number: 37100-04363
$951.35 MSRP: $1394.20
You Save: $442.85 (32%)
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft
- Replaces: 37100-04362, 37100-04361, 37100-04360
- Item Weight: 42.10 Pounds
- Item Dimensions: 90.5 x 7.1 x 7.2 inches
- Condition: New
- SKU: 37100-04363
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2005 Toyota Tacoma Submodels:
- Base, TRD Pro | 6 Cyl 4.0 L GAS
View related parts
2005 Toyota Tacoma Drive Shaft
Part Number: 37100-04321
$848.63 MSRP: $1243.68
You Save: $395.05 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft
- Replaces: 37100-04320
- Item Weight: 14.60 Pounds
- Item Dimensions: 33.7 x 6.8 x 5.6 inches
- Condition: New
- SKU: 37100-04321
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2005 Toyota Tacoma Submodels:
- Base, Pre Runner, X-Runner | 6 Cyl 4.0 L GAS
View related parts
2005 Toyota Tacoma Drive Shaft
Part Number: 37100-04352
$595.75 MSRP: $873.08
You Save: $277.33 (32%)
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft
- Replaces: 37100-04350, 37100-04351
- Part Name Code: 37110
- Item Weight: 46.60 Pounds
- Item Dimensions: 86.1 x 7.1 x 7.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 37100-04352
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2005 Toyota Tacoma Submodels:
- Base, Pre Runner, X-Runner | 6 Cyl 4.0 L GAS
View related parts
2005 Toyota Tacoma Drive Shaft
Part Number: 37100-04343
$924.11 MSRP: $1354.29
You Save: $430.18 (32%)
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft
- Replaces: 37100-04342, 37100-04341, 37100-04340
- Item Weight: 38.80 Pounds
- Item Dimensions: 76.2 x 7.4 x 7.1 inches
- Condition: New
- SKU: 37100-04343
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2005 Toyota Tacoma Submodels:
- Base, TRD Pro | 6 Cyl 4.0 L GAS
View related parts
2005 Toyota Tacoma Drive Shaft, Front
Part Number: 37140-04041
$293.57 MSRP: $419.14
You Save: $125.57 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft; Shaft Assembly, Propeller, Front
- Position: Front
- Replaces: 37140-04040
- Part Name Code: 37140
- Item Weight: 15.10 Pounds
- Item Dimensions: 34.7 x 6.7 x 5.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 37140-04041
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2005 Toyota Tacoma Submodels:
- Base, Pre Runner, TRD Pro, X-Runner | 6 Cyl 4.0 L GAS
View related parts
2005 Toyota Tacoma Drive Shaft
Part Number: 37100-04332
$923.77 MSRP: $1353.79
You Save: $430.02 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft
- Replaces: 37100-04330, 37100-04331
- Condition: New
- SKU: 37100-04332
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following 2005 Toyota Tacoma Submodels:
- Base, TRD Pro | 6 Cyl 4.0 L GAS
View related parts
2005 Toyota Tacoma Drive Shaft
Part Number: 37100-04282
$855.32 MSRP: $1253.49
You Save: $398.17 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft
- Replaces: 37100-04280, 37100-04281
- Item Weight: 44.00 Pounds
- Item Dimensions: 78.4 x 7.2 x 7.2 inches
- Condition: New
- SKU: 37100-04282
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2005 Toyota Tacoma Submodels:
- Base | 4 Cyl 2.7 L GAS
View related parts
2005 Toyota Tacoma Drive Shaft
Part Number: 37100-04311
$822.75 MSRP: $1205.75
You Save: $383.00 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft
- Replaces: 37100-04310
- Item Weight: 22.20 Pounds
- Item Dimensions: 84.2 x 7.1 x 7.1 inches
- Condition: New
- SKU: 37100-04311
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2005 Toyota Tacoma Submodels:
- Pre Runner | 4 Cyl 2.7 L GAS
View related parts
2005 Toyota Tacoma Drive Shaft
Part Number: 37100-04371
$620.72 MSRP: $909.68
You Save: $288.96 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft
- Replaces: 37100-04370
- Part Name Code: 37110
- Item Weight: 15.00 Pounds
- Item Dimensions: 33.7 x 6.7 x 5.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 37100-04371
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2005 Toyota Tacoma Submodels:
- X-Runner | 6 Cyl 4.0 L GAS
View related parts
2005 Toyota Tacoma Drive Shaft
Part Number: 37100-04291
$595.75 MSRP: $873.08
You Save: $277.33 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft
- Replaces: 37100-04290
- Part Name Code: 37110
- Item Weight: 15.00 Pounds
- Item Dimensions: 33.7 x 6.9 x 5.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 37100-04291
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2005 Toyota Tacoma Submodels:
- Base | 4 Cyl 2.7 L GAS
View related parts
2005 Toyota Tacoma Drive Shaft
Part Number: 37100-04302
$640.36 MSRP: $938.45
You Save: $298.09 (32%)
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft
- Replaces: 37100-04300, 37100-04301
- Part Name Code: 37110
- Item Weight: 49.10 Pounds
- Item Dimensions: 82.4 x 8.3 x 8.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 37100-04302
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2005 Toyota Tacoma Submodels:
- Base | 4 Cyl 2.7 L GAS
View related parts
2005 Toyota Tacoma Drive Shaft
Part Number: 37110-04172
$544.90 MSRP: $798.56
You Save: $253.66 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft
- Replaces: 37110-04170, 37110-04171
- Condition: New
- SKU: 37110-04172
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following 2005 Toyota Tacoma Submodels:
- Base | 4 Cyl 2.7 L GAS
View related parts
2005 Toyota Tacoma Drive Shaft
Part Number: 37110-04201
$458.30 MSRP: $671.65
You Save: $213.35 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft
- Replaces: 37110-04200
- Item Weight: 15.00 Pounds
- Item Dimensions: 33.7 x 6.9 x 5.4 inches
- Condition: New
- SKU: 37110-04201
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2005 Toyota Tacoma Submodels:
- Pre Runner | 4 Cyl 2.7 L GAS
View related parts
2005 Toyota Tacoma Drive Shaft
Part Number: 37110-04191
$408.70 MSRP: $598.96
You Save: $190.26 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft
- Replaces: 37110-04190
- Part Name Code: 37110
- Item Weight: 15.30 Pounds
- Item Dimensions: 33.4 x 6.7 x 5.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 37110-04191
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2005 Toyota Tacoma Submodels:
- Base | 4 Cyl 2.7 L GAS
View related parts
2005 Toyota Tacoma Drive Shaft
Part Number: 37110-04182
$396.22 MSRP: $580.66
You Save: $184.44 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft
- Replaces: 37110-04181, 37110-04180
- Part Name Code: 37110
- Item Weight: 22.00 Pounds
- Item Dimensions: 60.6 x 6.1 x 6.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 37110-04182
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2005 Toyota Tacoma Submodels:
- Base | 4 Cyl 2.7 L GAS
View related parts
2005 Toyota Tacoma Drive Shaft, Front
Part Number: 37140-04050
$319.90 MSRP: $456.74
You Save: $136.84 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft; Shaft Assembly, Propeller, Front
- Position: Front
- Part Name Code: 37140
- Item Weight: 14.90 Pounds
- Item Dimensions: 33.4 x 6.8 x 5.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 37140-04050
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2005 Toyota Tacoma Submodels:
- Base, Pre Runner, X-Runner | 4 Cyl 2.7 L GAS, 6 Cyl 4.0 L GAS
View related parts
2005 Toyota Tacoma Drive Shaft
Part Number: 37100-04382
$615.50 MSRP: $902.02
You Save: $286.52 (32%)
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft
- Replaces: 37100-04381, 37100-04380
- Part Name Code: 37110
- Item Weight: 93.50 Pounds
- Item Dimensions: 97.9 x 10.4 x 10.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 37100-04382
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2005 Toyota Tacoma Submodels:
- Base, Pre Runner, X-Runner | 6 Cyl 4.0 L GAS

2005 Toyota Tacoma Drive Shaft

Looking for affordable OEM 2005 Toyota Tacoma Drive Shaft? Explore our comprehensive catalogue of genuine 2005 Toyota Tacoma Drive Shaft. All our parts are covered by the manufacturer's warranty. Plus, our straightforward return policy and speedy delivery service ensure an unparalleled shopping experience. We look forward to your visit!

2005 Toyota Tacoma Drive Shaft Parts Q&A

Q: How to service and repair the Drive Shaft on 2005 Toyota Tacoma?
A: The first step of servicing and repairing the rear propeller with center bearing shaft assembly in 2WD Access Cab and Double Cab types requires you to mark the propeller shaft flange and differential flange before you remove 4 nuts, 4 bolts and 4 washers to detach the propeller shaft. The first step includes removing the frame crossmember's 2 center support bearing bolts then pulling out the propeller shaft while inserting Special Service Tool: 09325-40010 into the transmission to stop oil leakage. The inspection of the propeller shaft universal joint spider bearing should include checks for wear and damage. Maximum axial play measurement must stay between 0 to 0.05 mm (0 to 0.002 inch). Replacement of the bearing is required if any failure issues occur. Follow these steps to extract the spider bearing by marking the propeller shaft then universal joint yoke followed by brass bar tapping before using needle nose pliers to uninstall the 4 snap rings. Special Service Tool: 09332-25010 should be used to push out the spider bearing from the propeller shaft while the shaft stays in a vise clamp position to avoid striking the shaft tube. Insert the removed spider bearings onto the spider before forcing it out of the yoke using the previous special tool. Besides checking for .6mm (0.024inch) maximum runout on the propeller with center bearing shaft assembly; perform another runout test on the propeller shaft. Procedure for center support bearing assembly No.1 includes fixing the yoke in a vice followed by chisel use to loosen lock nuts and then marking yoke and shaft before removing the center yoke, spacer, and center support bearing. Visual inspection of the center bearing must be done for normal function which includes a replacement if found defective. Place center support bearing assembly No.1 on the intermediate shaft before coating its splines with MP grease No.2 and positioning the matchmarks correctly to install the spacer. Place the yoke in a vice before installing the bearing with a new lock nut to 182 Nm (1,850 kgf-cm, 134 ft. lbs.) torque which should be followed by loosening then re-torquing to 69 Nm (700 kgf-cm, 51 ft. lbs.) before staking the lock nut last. To install the propeller shaft universal joint spider bearing start by applying MP grease No.2 to fresh components then inserting the spider into the flange yoke followed by measuring dimensions A and B for snap ring selection and pressing the spider bearing into the snap ring groove using Special Service Tool: 09332-25010. Next apply new snap rings to the grooves before evaluating the spider bearings for dimensional wear and their axial position. After removing the special service tool from the extension housing the propeller shaft assembly can be installed while keeping the matchmarks aligned and fastening it with 4 bolts, 4 nuts and 4 washers that must reach a torque of 88 Nm (899 kgf-cm, 65 ft. lbs.). Install center support bearing number one provisionally with two mounting bolts while directing the drain hole towards the bottom and adjust the bearing to sit between 0 and 1.0 mm (0 and 0.039 inch) of center line during unladen condition before tightening the bolts to 36 Nm (369 kgf-cm, 27 ft. lbs.). Check for transmission oil leaks after procedure completion.

Related 2005 Toyota Tacoma Parts

Alternate Year Models

2004 Toyota Tacoma Drive Shaft 2006 Toyota Tacoma Drive Shaft