How to service and repair the drive shaft on 2004 Toyota Tacoma?

The drive/propeller shaft service process requires starting with flange matchmark placement before using 4 nuts and washers and bolts to remove the intermediate shaft. The 3-joint nut removal requires a chisel and hammer operation to unstake the nut part before using Special Service Tool: 09330-00021 to stabilize the flange when removing the nut alongside the spacer. To obtain the flange from the intermediate shaft apply Special Service Tool: 09950-30012 (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03020) after first marking both components. Next remove the spacer. To assess the propeller shaft and intermediate shaft quality inspect both components using a dial indicator which should detect less than 0.8 mm (0.031 inch) maximum runout thus requiring replacement in case of excessive runout values. Evaluate the spider bearings for damage and wear by checking their axial movement with a dial indicator while ensuring the result remains below 0.05 mm (0.0020 inch). If necessary, replace the bearings. When inspecting the center support bearing of 3-joint types one must check its ability to rotate freely and replace if it fails this requirement. The reassembly process requires placing the center support bearing and spacer with its tine cutout to the rear position before applying MP grease to the intermediate shaft splines and matching the marks and installing the flange. Ensure the replacement of center flange or intermediate shaft follows proper direction between the front yoke of intermediate shaft and the rear yoke of the propeller shaft. Special Service Tool: 09330-00021 should be used to secure the flange while tightening a new nut to 181 Nm (1,850 kgf-cm, 134 ft. lbs.) torque to position the bearing correctly. The nut should later be loosened to 69 Nm (700 kgf-cm, 51 ft. lbs.) before hammering a chisel stake. After properly orienting the propeller shaft and intermediate shaft flange matchmarks, secure them with four bolts and washers and nuts and tighten the nuts to 74 Nm (750 kgf-cm, 54 ft. lbs.).

OEM 2004 Toyota Tacoma Drive Shaft

Axle Shaft

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

16 Drive Shafts found

View related parts
2004 Toyota Tacoma Drive Shaft
Part Number: 37100-3D260
$1300.81 MSRP: $1906.35
You Save: $605.54 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft; Shaft Assembly, Propeller W/Center Bearing
- Manufacturer Note: TYPE B:REFER TO ILLUSTRATION
- Replaces: 37100-3D150
- Part Name Code: 37100
- Item Weight: 43.20 Pounds
- Item Dimensions: 59.3 x 11.9 x 7.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 37100-3D260
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2004 Toyota Tacoma Submodels:
- Base, DLX, Limited, Pre Runner, SR5, S-Runner | 6 Cyl 3.4 L GAS
View related parts
2004 Toyota Tacoma Drive Shaft
Part Number: 37100-3D230
$1274.82 MSRP: $1868.27
You Save: $593.45 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft; Shaft Assembly, Propeller W/Center Bearing
- Manufacturer Note: TYPE B:REFER TO ILLUSTRATION
- Replaces: 37100-35750
- Part Name Code: 37100
- Item Weight: 42.80 Pounds
- Item Dimensions: 75.9 x 8.2 x 7.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 37100-3D230
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2004 Toyota Tacoma Submodels:
- Base, DLX, Limited, Pre Runner, SR5, S-Runner | 4 Cyl 2.4 L GAS, 4 Cyl 2.7 L GAS, 6 Cyl 3.4 L GAS
View related parts
2004 Toyota Tacoma Drive Shaft
Part Number: 37100-3D220
$1159.39 MSRP: $1699.10
You Save: $539.71 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft; Shaft Assembly, Propeller W/Center Bearing
- Replaces: 37100-35740
- Part Name Code: 37100
- Item Weight: 45.90 Pounds
- Item Dimensions: 74.9 x 9.3 x 7.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 37100-3D220
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2004 Toyota Tacoma Submodels:
- Base, DLX, Limited, Pre Runner, SR5, S-Runner | 6 Cyl 3.4 L GAS
View related parts
2004 Toyota Tacoma Drive Shaft
Part Number: 37110-3D400
$696.25 MSRP: $1020.36
You Save: $324.11 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft
- Part Name Code: 37110
- Item Weight: 15.60 Pounds
- Item Dimensions: 33.4 x 6.9 x 5.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 37110-3D400
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2004 Toyota Tacoma Submodels:
- Base, Pre Runner | 4 Cyl 2.4 L GAS, 4 Cyl 2.7 L GAS
View related parts
2004 Toyota Tacoma Drive Shaft
Part Number: 37100-3D030
$648.12 MSRP: $949.83
You Save: $301.71 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft; Shaft Assembly, Propeller W/Center Bearing
- Part Name Code: 37100
- Item Weight: 43.60 Pounds
- Item Dimensions: 58.1 x 12.2 x 7.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 37100-3D030
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2004 Toyota Tacoma Submodels:
- Base, DLX, Limited, Pre Runner, SR5, S-Runner | 6 Cyl 3.4 L GAS
View related parts
2004 Toyota Tacoma Drive Shaft, Front
Part Number: 37140-35170
$439.37 MSRP: $643.90
You Save: $204.53 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft; Shaft Assembly, Propeller, Front
- Position: Front
- Part Name Code: 37140
- Item Weight: 16.10 Pounds
- Item Dimensions: 30.3 x 5.4 x 5.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 37140-35170
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2004 Toyota Tacoma Submodels:
- Base, DLX, Pre Runner, SR5 | 4 Cyl 2.4 L GAS, 4 Cyl 2.7 L GAS
View related parts
2004 Toyota Tacoma Drive Shaft
Part Number: 37110-04040
$392.13 MSRP: $574.68
You Save: $182.55 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft
- Manufacturer Note: DANA
- Replaces: 37110-3D200
- Part Name Code: 37110
- Item Weight: 14.60 Pounds
- Item Dimensions: 34.4 x 6.8 x 5.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 37110-04040
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2004 Toyota Tacoma Submodels:
- Base, DLX, Pre Runner, SR5 | 4 Cyl 2.4 L GAS, 4 Cyl 2.7 L GAS
View related parts
2004 Toyota Tacoma Drive Shaft, Front
Part Number: 37140-35180
$393.04 MSRP: $576.01
You Save: $182.97 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft; Shaft Assembly, Propeller, Front
- Position: Front
- Part Name Code: 37140
- Item Weight: 15.30 Pounds
- Item Dimensions: 29.5 x 5.3 x 5.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 37140-35180
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2004 Toyota Tacoma Submodels:
- Base, DLX, Limited, Pre Runner, SR5, S-Runner | 6 Cyl 3.4 L GAS
View related parts
2004 Toyota Tacoma Drive Shaft, Front
Part Number: 37140-60300
$380.78 MSRP: $558.04
You Save: $177.26 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft; Shaft Assembly, Propeller, Front
- Position: Front
- Part Name Code: 37140
- Item Weight: 16.70 Pounds
- Item Dimensions: 30.6 x 5.4 x 5.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 37140-60300
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2004 Toyota Tacoma Submodels:
- Base, DLX, Limited, Pre Runner, SR5, S-Runner | 6 Cyl 3.4 L GAS
View related parts
2004 Toyota Tacoma Drive Shaft, Front
Part Number: 37140-35160
$380.78 MSRP: $558.04
You Save: $177.26 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft; Shaft Assembly, Propeller, Front
- Position: Front
- Part Name Code: 37140
- Item Weight: 15.20 Pounds
- Item Dimensions: 30.3 x 5.5 x 5.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 37140-35160
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2004 Toyota Tacoma Submodels:
- Base, DLX, Pre Runner, SR5 | 4 Cyl 2.4 L GAS, 4 Cyl 2.7 L GAS
View related parts
2004 Toyota Tacoma Drive Shaft
Part Number: 37100-3D240
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft; Shaft Assembly, Propeller W/Center Bearing
- Manufacturer Note: TYPE B:REFER TO ILLUSTRATION
- Replaces: 37100-35790
- Part Name Code: 37100
- Item Weight: 40.40 Pounds
- Item Dimensions: 58.1 x 12.2 x 7.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 37100-3D240
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2004 Toyota Tacoma Submodels:
- Base, DLX, Pre Runner, SR5 | 4 Cyl 2.4 L GAS, 4 Cyl 2.7 L GAS
View related parts
2004 Toyota Tacoma Drive Shaft
Part Number: 37100-3D250
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft; Shaft Assembly, Propeller W/Center Bearing
- Manufacturer Note: TYPE B:REFER TO ILLUSTRATION
- Replaces: 37100-3D140
- Part Name Code: 37100
- Item Weight: 41.20 Pounds
- Item Dimensions: 59.9 x 12.1 x 7.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 37100-3D250
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2004 Toyota Tacoma Submodels:
- Base, DLX, Pre Runner, SR5 | 4 Cyl 2.4 L GAS, 4 Cyl 2.7 L GAS
View related parts
2004 Toyota Tacoma Drive Shaft
Part Number: 37110-3D390
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft
- Part Name Code: 37110
- Item Weight: 41.60 Pounds
- Item Dimensions: 58.1 x 12.1 x 7.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 37110-3D390
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2004 Toyota Tacoma Submodels:
- Base, Pre Runner | 4 Cyl 2.4 L GAS, 4 Cyl 2.7 L GAS
View related parts
2004 Toyota Tacoma Drive Shaft
Part Number: 37100-35820
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft; Shaft Assembly, Propeller W/Center Bearing
- Part Name Code: 37100
- Item Weight: 40.80 Pounds
- Item Dimensions: 58.7 x 12.1 x 7.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 37100-35820
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2004 Toyota Tacoma Submodels:
- Base, DLX, Pre Runner, SR5 | 4 Cyl 2.4 L GAS, 4 Cyl 2.7 L GAS
View related parts
2004 Toyota Tacoma Drive Shaft
Part Number: 37100-35830
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft; Shaft Assembly, Propeller W/Center Bearing
- Part Name Code: 37100
- Item Weight: 15.30 Pounds
- Item Dimensions: 34.0 x 6.8 x 5.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 37100-35830
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2004 Toyota Tacoma Submodels:
- Base, DLX, SR5 | 4 Cyl 2.4 L GAS, 4 Cyl 2.7 L GAS
View related parts
2004 Toyota Tacoma Drive Shaft
Part Number: 37110-3D410
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft
- Part Name Code: 37110
- Item Weight: 42.00 Pounds
- Item Dimensions: 57.6 x 11.8 x 7.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 37110-3D410
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2004 Toyota Tacoma Submodels:
- Base, Pre Runner | 4 Cyl 2.7 L GAS

2004 Toyota Tacoma Drive Shaft

Looking for affordable OEM 2004 Toyota Tacoma Drive Shaft? Explore our comprehensive catalogue of genuine 2004 Toyota Tacoma Drive Shaft. All our parts are covered by the manufacturer's warranty. Plus, our straightforward return policy and speedy delivery service ensure an unparalleled shopping experience. We look forward to your visit!

2004 Toyota Tacoma Parts Questions & Experts Answers

Q: How to service and repair the drive shaft on 2004 Toyota Tacoma?
A: The drive/propeller shaft service process requires starting with flange matchmark placement before using 4 nuts and washers and bolts to remove the intermediate shaft. The 3-joint nut removal requires a chisel and hammer operation to unstake the nut part before using Special Service Tool: 09330-00021 to stabilize the flange when removing the nut alongside the spacer. To obtain the flange from the intermediate shaft apply Special Service Tool: 09950-30012 (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03020) after first marking both components. Next remove the spacer. To assess the propeller shaft and intermediate shaft quality inspect both components using a dial indicator which should detect less than 0.8 mm (0.031 inch) maximum runout thus requiring replacement in case of excessive runout values. Evaluate the spider bearings for damage and wear by checking their axial movement with a dial indicator while ensuring the result remains below 0.05 mm (0.0020 inch). If necessary, replace the bearings. When inspecting the center support bearing of 3-joint types one must check its ability to rotate freely and replace if it fails this requirement. The reassembly process requires placing the center support bearing and spacer with its tine cutout to the rear position before applying MP grease to the intermediate shaft splines and matching the marks and installing the flange. Ensure the replacement of center flange or intermediate shaft follows proper direction between the front yoke of intermediate shaft and the rear yoke of the propeller shaft. Special Service Tool: 09330-00021 should be used to secure the flange while tightening a new nut to 181 Nm (1,850 kgf-cm, 134 ft. lbs.) torque to position the bearing correctly. The nut should later be loosened to 69 Nm (700 kgf-cm, 51 ft. lbs.) before hammering a chisel stake. After properly orienting the propeller shaft and intermediate shaft flange matchmarks, secure them with four bolts and washers and nuts and tighten the nuts to 74 Nm (750 kgf-cm, 54 ft. lbs.).

Related 2004 Toyota Tacoma Parts

Alternate Year Models

2003 Toyota Tacoma Drive Shaft 2005 Toyota Tacoma Drive Shaft