Other Name: Belt Assembly, Front Seat; Seat Belt Lap and Shoulder Belt, Front Right, Right; Belt & Retractor; Belt Assembly, Front Seat Outer, Passenger Side
Position: Passenger Side
Part Name Code: 73210
Item Weight: 4.40 Pounds
Item Dimensions: 10.3 x 7.1 x 6.2 inches
Condition: New
Fitment Type: Direct Replacement
SKU: 73210-02142-B1
Warranty: This genuine part is guaranteed by Toyota's
factory warranty.
Other Name: Belt Assembly, Front Seat; Seat Belt Lap and Shoulder Belt, Front Left, Left; Belt & Retractor; Belt Assembly, Front Seat Outer, Driver Side
Position: Driver Side
Part Name Code: 73220
Item Weight: 4.20 Pounds
Item Dimensions: 10.5 x 7.4 x 6.2 inches
Condition: New
Fitment Type: Direct Replacement
SKU: 73220-02132-B1
Warranty: This genuine part is guaranteed by Toyota's
factory warranty.
Other Name: Belt Assembly, Rear Seat; Seat Belt Lap and Shoulder Belt, Rear Right; Belt & Retractor; Belt Assembly, Rear Seat 3 Point Type, Outer Passenger Side
Manufacturer Note: DK. GRAY,TRIM13,14
Position: Outer Passenger Side
Part Name Code: 73360
Item Weight: 2.50 Pounds
Item Dimensions: 12.4 x 11.1 x 8.2 inches
Condition: New
Fitment Type: Direct Replacement
SKU: 73360-01100-B0
Warranty: This genuine part is guaranteed by Toyota's
factory warranty.
Other Name: Belt Assembly, Rear Seat; Seat Belt Lap and Shoulder Belt, Rear Left; Belt & Retractor; Belt Assembly, Rear Seat 3 Point Type, Outer Driver Side
Manufacturer Note: DK. GRAY,TRIM13,14
Position: Outer Driver Side
Part Name Code: 73370
Item Weight: 2.40 Pounds
Condition: New
Fitment Type: Direct Replacement
SKU: 73370-01100-B0
Warranty: This genuine part is guaranteed by Toyota's
factory warranty.
Other Name: Belt Assembly, Front Seat; Seat Belt Receptacle, Front Right; Latch; Belt Assembly, Front Seat Inner, Passenger Side
Manufacturer Note: DK.GRAY,TRIM13,14
Position: Passenger Side
Part Name Code: 73230
Item Weight: 1.00 Pounds
Item Dimensions: 14.1 x 11.3 x 2.2 inches
Condition: New
Fitment Type: Direct Replacement
SKU: 73230-01050-B0
Warranty: This genuine part is guaranteed by Toyota's
factory warranty.
More Info
Fits the following 2006 Toyota Matrix Submodels:
Base, XR, XRS | 4 Cyl 1.8 L GAS
2006 Toyota Matrix Seat Belt
Looking for affordable OEM 2006 Toyota Matrix Seat Belt? Explore our comprehensive catalogue of genuine 2006 Toyota Matrix Seat Belt. All our parts are covered by the manufacturer's warranty. Plus, our straightforward return policy and speedy delivery service ensure an unparalleled shopping experience. We look forward to your visit!
2006 Toyota Matrix Parts Questions & Experts Answers
Q: How to replace the rear seat belt on 2006 Toyota Matrix?
A: You must remove the rear door scuff plates from both sides together with the rear door opening trims while uninstalling the tonneau cover assembly followed by deck board No.2, deck board sub-assembly and deck floor box rear assembly; then take off the luggage compartment tray and back door Weather Strip and finally remove the deck trim cover rear. After removing the rear seat cushion assembly people should continue by removing the rear seat back assembly followed by the rear seat side garnishes (RH and LH) as well as the deck trim side panel assemblies (RH and LH). The rear seat 3-point type belt assembly outer should be disconnected by first removing the shoulder anchor cover with a screwdriver whose tip should be taped beforehand followed by the bolt removal to disconnect the assembly at both shoulder anchor and RH floor anchor points. Detach the rear seat belt assembly outer center through a procedure that includes removal of the rear seat back board RH and the rear seat shoulder belt cover and two bolts that secure this component. The rear seat inner assembly which contains the center belt on the LH side requires bolt removal for disconnection. Install the new child restraint seat anchor bracket sub-assembly RH by attaching its two bolts before tightening them to 18.1 N.m (185 kgf.cm, 13.3 ft.lbf). The rear seat belt assembly outer center (retractor) requires installation using two bolts tightened to 41.2 N.m (420 kgf.cm, 30 ft.lbf). Testing ELR requires gentle belt tilting followed by pulling until the restraint activates at 15 degrees of tilt yet locks beyond 45 degrees; a nonfunctional assembly needs replacement. Perform a belt lock test by quick belt extraction before verifying the child restraint system function that allows full belt retraction followed by successful belt extraction after complete retraction. Use the bolt to attach the floor anchor and rear seat belt assembly inner section while torquing it to 41.2 N.m (420 kgf.cm, 30 ft.lbf) and verify that the anchor section avoids contact with floor panel protrusions. Progress with the same installation procedure to mount the rear seat inner w/center belt assembly LH while applying 41.2 N.m (420 kgf.cm, 30 ft.lbf) torque before installing the rear seat 3-point type belt assembly outer component by following the child restraint system function checks described previously at 4.9 N.m (50 kgf.cm, 43 in.lbf) and 41.2 N.m (420 kgf.cm, 30 ft.lbf) torque values. To complete the installation process fit in the rear seat back assembly and rear seat cushion assembly.