Other Name: Belt Assembly, Front Seat; Seat Belt Lap and Shoulder Belt, Front Right, Right; Belt & Retractor; Belt Assembly, Front Seat Outer, Passenger Side
Position: Passenger Side
Part Name Code: 73210
Item Weight: 4.40 Pounds
Item Dimensions: 10.3 x 7.1 x 6.2 inches
Condition: New
Fitment Type: Direct Replacement
SKU: 73210-02142-B1
Warranty: This genuine part is guaranteed by Toyota's
factory warranty.
Other Name: Belt Assembly, Front Seat; Seat Belt Lap and Shoulder Belt, Front Left, Left; Belt & Retractor; Belt Assembly, Front Seat Outer, Driver Side
Position: Driver Side
Part Name Code: 73220
Item Weight: 4.20 Pounds
Item Dimensions: 10.5 x 7.4 x 6.2 inches
Condition: New
Fitment Type: Direct Replacement
SKU: 73220-02132-B1
Warranty: This genuine part is guaranteed by Toyota's
factory warranty.
Other Name: Belt Assembly, Rear Seat; Seat Belt Lap and Shoulder Belt, Rear Right; Belt & Retractor; Belt Assembly, Rear Seat 3 Point Type, Outer Passenger Side
Manufacturer Note: DK. GRAY,TRIM13,14
Position: Outer Passenger Side
Part Name Code: 73360
Item Weight: 2.50 Pounds
Item Dimensions: 12.4 x 11.1 x 8.2 inches
Condition: New
Fitment Type: Direct Replacement
SKU: 73360-01100-B0
Warranty: This genuine part is guaranteed by Toyota's
factory warranty.
Other Name: Belt Assembly, Rear Seat; Seat Belt Lap and Shoulder Belt, Rear Left; Belt & Retractor; Belt Assembly, Rear Seat 3 Point Type, Outer Driver Side
Manufacturer Note: DK. GRAY,TRIM13,14
Position: Outer Driver Side
Part Name Code: 73370
Item Weight: 2.40 Pounds
Condition: New
Fitment Type: Direct Replacement
SKU: 73370-01100-B0
Warranty: This genuine part is guaranteed by Toyota's
factory warranty.
Other Name: Belt Assembly, Front Seat; Seat Belt Receptacle, Front Right; Latch; Belt Assembly, Front Seat Inner, Passenger Side
Manufacturer Note: DK.GRAY,TRIM13,14
Position: Passenger Side
Part Name Code: 73230
Item Weight: 1.00 Pounds
Item Dimensions: 14.1 x 11.3 x 2.2 inches
Condition: New
Fitment Type: Direct Replacement
SKU: 73230-01050-B0
Warranty: This genuine part is guaranteed by Toyota's
factory warranty.
More Info
Fits the following 2005 Toyota Matrix Submodels:
Base, XR, XRS | 4 Cyl 1.8 L GAS
2005 Toyota Matrix Seat Belt
Looking for affordable OEM 2005 Toyota Matrix Seat Belt? Explore our comprehensive catalogue of genuine 2005 Toyota Matrix Seat Belt. All our parts are covered by the manufacturer's warranty. Plus, our straightforward return policy and speedy delivery service ensure an unparalleled shopping experience. We look forward to your visit!
2005 Toyota Matrix Seat Belt Parts Q&A
Q: How to replace the front seat belt on the RH side on 2005 Toyota Matrix?
A: Users should disconnect the negative terminal of the battery as their first step when replacing the RH-side front seat belt. Begin by removing the front seat assembly from the right-hand side then proceed to remove the front seat inner belt assembly RH with bolt and belt removal. Begin removing the front door scuff plate RH together with the rear door scuff plate RH, front door opening trim RH, rear door opening trim RH and center pillar garnish lower RH. Start seat belt pretensioner removal procedures at least 90 seconds after both engine shut-off and negative battery terminal detachment for the task. Start by using a screwdriver with its tip taped then carefully separate the shoulder anchor cover before removing the bolt that leads to disconnection at the front seat outer belt from its shoulder anchor placement. A screwdriver will help you take off the floor anchor cover before removing the bolt to disconnect the front seat outer belt assembly RH from the floor anchor. The lock section of the pretensioner connector must be pulled horizontally before extracting it. You must disconnect the front seat outer belt assembly RH through the removal of its 2 bolts. Proceed to remove the center pillar garnish RH along with the front shoulder belt anchor adjuster assembly by disconnecting its bolt. The front shoulder belt anchor adjuster assembly needs installation by bolting it in place while torquing to 41.2 N.m (420 kgf.cm, 30 ft.lbf). The front seat outer belt assembly RH should be installed without taking apart the retractor; during installation check the ELR through gentle belt tilting which should not lock under 15 degrees tilt yet should lock when reaching 45 degrees tilt or higher. If the assembly does not operate correctly replace it. Secure the retractor with two bolts where the upper fastener reaches 4.9 N.m (50 kgf.cm, 43 in.lbf) and the lower fastener reaches 41.2 N.m (420 kgf.cm, 30 ft.lbf). Begin installing the shoulder anchor with bolt before tightening it to 41.2 N.m (420 kgf.cm, 30 ft.lbf), and continue with the shoulder anchor cover then floor anchor and its bolt which needs 41.2 N.m (420 kgf.cm, 30 ft.lbf) torque and finishes with the floor anchor cover installation. Verify that the belt functions properly when you swiftly pull it after installing the ELR; replace the front seat outer belt assembly if the operation is not correct. End these procedures by installing the front seat inner belt assembly RH with its bolt and torquing it to 41.2 N.m (420 kgf.cm, 30 ft.lbf).