How to Service and Repair an Axle Shaft on 2005 Toyota Land Cruiser?

Begin the axle shaft servicing and repair procedures by taking off the rear wheel using 131 Nm (1,340 kgf-cm, 97 ft. lbs.) torque. The brake line needs Special Service Tool: 09023-00101 to disconnect it while applying 15 Nm (150 kgf-cm, 11 ft. lbs.) torque to remove the clip. After removing the brake caliper and its disc, disconnect the two bolts with their attached washers by applying torque of 103 Nm (1,050 kgf-cm, 76 ft. lbs.). Use a dial indicator to measure bearing backlash because values beyond 0.6 mm (0.024 inch) will require replacement of the bearing. The outside surface of the axle shaft should receive a deviation check at the proximity of the bolt hole using a 0.05 mm (0.0020 inch) limit. Replacing the axle shaft becomes necessary if the limit is exceeded. The axle shaft assembly removal procedure starts with removing the parking brake assembly and then proceeding with the four nuts at 123 Nm torque (1,250 kgf-cm, 91 ft. lbs.) until the axle shaft assembly can be extracted while protecting the oil seal from damage. You should remove the O-ring from inside the bearing case. The correct installation steps involve reversing the removal process and afterward filling the brake reservoir with fluid and conducting brake bleed procedures and leak checkups and testing the ABS speed sensor signal.

OEM 2005 Toyota Land Cruiser Axle Shaft

Car Axle Shaft

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

4 Axle Shafts found

View related parts
2005 Toyota Land Cruiser Axle Assembly, Front
Part Number: 43430-60040
$372.28 MSRP: $572.11
You Save: $199.83 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Front Drive; CV Axle Assembly, Front Left, Front Right; Joint Kit, Drive Shaft; GSP Cv Axle; Axle Shaft; Shaft Assembly, Front Drive, Passenger Side; Shaft Assembly, Front Drive, Driver Side; CV Axle Assembly
- Position: Front
- Item Weight: 33.30 Pounds
- Item Dimensions: 31.5 x 6.3 x 6.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 43430-60040
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2005 Toyota Land Cruiser Submodels:
- Base | 8 Cyl 4.7 L GAS
View related parts
2005 Toyota Land Cruiser Axle Shaft, Driver Side
Part Number: 41337-60010
$233.40 MSRP: $333.24
You Save: $99.84 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft, Differential Side Gear Intermediate; Drive Axle Shaft, Front Right; Axle Shafts; Output Shaft; Shaft Sub-Assembly, Differential Side Gear, Driver Side
- Position: Driver Side
- Part Name Code: 41304V
- Item Weight: 7.20 Pounds
- Item Dimensions: 7.4 x 6.9 x 5.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 41337-60010
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2005 Toyota Land Cruiser Submodels:
- Base | 8 Cyl 4.7 L GAS
View related parts
2005 Toyota Land Cruiser Shaft, Rear Axle, Driver Side
Part Number: 42302-60901
$824.73 MSRP: $1208.65
You Save: $383.92 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Sub-Assembly Rear Axle Right-Hand; Axle Shaft
- Position: Driver Side
- Part Name Code: 42312
- Item Weight: 15.60 Pounds
- Item Dimensions: 28.2 x 8.6 x 7.9 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 42302-60901
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2005 Toyota Land Cruiser Submodels:
- Base | 8 Cyl 4.7 L GAS
View related parts
2005 Toyota Land Cruiser Shaft, Rear Axle, Passenger Side
Part Number: 42301-60901
$698.06 MSRP: $1023.01
You Save: $324.95 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Sub-Assembly Rear Axle Right-Hand; Axle Shaft
- Position: Passenger Side
- Part Name Code: 42311L
- Item Weight: 15.20 Pounds
- Item Dimensions: 29.3 x 9.1 x 7.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 42301-60901
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2005 Toyota Land Cruiser Submodels:
- Base | 8 Cyl 4.7 L GAS

2005 Toyota Land Cruiser Axle Shaft

Looking for affordable OEM 2005 Toyota Land Cruiser Axle Shaft? Explore our comprehensive catalogue of genuine 2005 Toyota Land Cruiser Axle Shaft. All our parts are covered by the manufacturer's warranty. Plus, our straightforward return policy and speedy delivery service ensure an unparalleled shopping experience. We look forward to your visit!

2005 Toyota Land Cruiser Parts Questions & Experts Answers

Q: How to Service and Repair an Axle Shaft on 2005 Toyota Land Cruiser?
A: Begin the axle shaft servicing and repair procedures by taking off the rear wheel using 131 Nm (1,340 kgf-cm, 97 ft. lbs.) torque. The brake line needs Special Service Tool: 09023-00101 to disconnect it while applying 15 Nm (150 kgf-cm, 11 ft. lbs.) torque to remove the clip. After removing the brake caliper and its disc, disconnect the two bolts with their attached washers by applying torque of 103 Nm (1,050 kgf-cm, 76 ft. lbs.). Use a dial indicator to measure bearing backlash because values beyond 0.6 mm (0.024 inch) will require replacement of the bearing. The outside surface of the axle shaft should receive a deviation check at the proximity of the bolt hole using a 0.05 mm (0.0020 inch) limit. Replacing the axle shaft becomes necessary if the limit is exceeded. The axle shaft assembly removal procedure starts with removing the parking brake assembly and then proceeding with the four nuts at 123 Nm torque (1,250 kgf-cm, 91 ft. lbs.) until the axle shaft assembly can be extracted while protecting the oil seal from damage. You should remove the O-ring from inside the bearing case. The correct installation steps involve reversing the removal process and afterward filling the brake reservoir with fluid and conducting brake bleed procedures and leak checkups and testing the ABS speed sensor signal.