How to replace a Speed Sensor on 2003 Toyota Highlander?

The replacement process for the skid control sensor begins by removing the rear wheel and disconnecting the connector from its sensor. The skid control sensor replacement process starts by taking off the LH rear disc brake caliper assembly followed by the removal of the rear disc. Secure the 4 bolts from the rear axle hub & bearing assembly RH to remove it. Mount the rear axle hub inside a soft jaw vise while the assembly needs replacement if the hub experiences sudden strong impacts or drops. Use a pin punch and hammer together with Special Service Tool to drive out pins from both attachments which will allow the removal of the tools from their special attachment point. Movement of the skid control sensor from the rear axle hub requires Special Service Tool: 09520-00031 (09520-00040), 09521-00020, 09950-00020 and 2 bolts (Diameter: 12 mm, pitch: 1.5 mm) by following precise steps to protect the sensor rotor while preventing surface damage of the axle hub and speed sensor. Clear both the new skid control sensor and the axle hub's contact surface from all foreign substance that could remain on the sensor rotor. A proper orientation of the skid control sensor connector should be maintained before pressing it onto the axle hub using Special Service Tool. Use the press tool to mount the sensor without hitting it directly with a hammer. Position the skid control sensor so it enters directly and proceed with slow insertion. Under post-installation procedures use 4 bolts to fasten the rear axle hub & bearing assembly RH while tightening them to 56 Nm (571 kgf-cm, 41 ft. lbs.). The installation sequence continues with the rear disc followed by the rear disc brake caliper assembly LH then the skid control sensor wire. Finish by installing the rear wheel and torquing it to 103 Nm then check the wheel alignment before verifying the ABS speed sensor signal.

OEM 2003 Toyota Highlander Speed Sensor

Speed Control Sensor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

6 Speed Sensors found

View related parts
2003 Toyota Highlander Speed Sensor
Part Number: 89413-08020
$138.64 MSRP: $196.26
You Save: $57.62 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor, Transmission; Vehicle Speed Sensor; Automatic Transmission Speed Sensor; Sensor, Speed; Sensor, Transmission Revolution
- Replaces: 89413-33020, 89413-24010, 89411-33010
- Item Weight: 0.60 Pounds
- Item Dimensions: 3.6 x 2.9 x 2.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 89413-08020
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2003 Toyota Highlander Submodels:
- Base, Limited, Sport | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L GAS
View related parts
2003 Toyota Highlander ABS Sensor, Rear
Part Number: 89544-48010
$200.95 MSRP: $246.44
You Save: $45.49 (19%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor, Skid Control; ABS Wheel Speed Sensor Tone Ring, Rear; Rear Right/Left Sensor; Rear Speed Sensor; Sensor Ring; ABS Rotor; Sensor; ABS Wheel Speed Sensor
- Position: Rear
- Replaces: 89544-48020, 89544-06020, 89544-06010
- Part Name Code: 89544
- Item Weight: 0.80 Pounds
- Item Dimensions: 10.4 x 6.4 x 1.7 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 89544-48010
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2003 Toyota Highlander Submodels:
- Base, Limited | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS
View related parts
2003 Toyota Highlander Speed Sensor, Rear Driver Side
Part Number: 89546-48020
$291.94 MSRP: $416.82
You Save: $124.88 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor, Speed, Rear Left-Hand; ABS Wheel Speed Sensor, Rear Left; ABS Sensor; Rear Speed Sensor; Sensor, Speed, Rear Driver Side; ABS Wheel Speed Sensor
- Position: Rear Driver Side
- Part Name Code: 89546
- Item Weight: 0.70 Pounds
- Item Dimensions: 7.2 x 4.8 x 1.9 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 89546-48020
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2003 Toyota Highlander Submodels:
- Base, Limited | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS
View related parts
2003 Toyota Highlander Sensor, Speed, Rear Passenger Side
Part Number: 89545-48020
$283.20 MSRP: $404.35
You Save: $121.15 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor, Speed, Rear Right-Hand; ABS Wheel Speed Sensor; ABS Sensor
- Position: Rear Passenger Side
- Part Name Code: 89545
- Item Weight: 0.70 Pounds
- Item Dimensions: 7.2 x 4.8 x 1.9 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 89545-48020
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2003 Toyota Highlander Submodels:
- Base, Limited | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS
View related parts
2003 Toyota Highlander Speed Sensor, Front Driver Side
Part Number: 89543-48020
$279.82 MSRP: $399.52
You Save: $119.70 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor, Speed, Front Left-Hand; ABS Wheel Speed Sensor, Front Left; ABS Sensor; Sensor, Speed, Front Driver Side; ABS Wheel Speed Sensor
- Position: Front Driver Side
- Part Name Code: 89543
- Item Weight: 0.90 Pounds
- Item Dimensions: 10.3 x 6.6 x 2.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 89543-48020
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2003 Toyota Highlander Submodels:
- Base, Limited | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS
View related parts
2003 Toyota Highlander Speed Sensor, Front Passenger Side
Part Number: 89542-48020
Product Specifications
- Other Name: Sensor, Speed, Front Right-Hand; ABS Wheel Speed Sensor, Front Right; ABS Sensor; Sensor, Speed, Front Passenger Side; ABS Wheel Speed Sensor
- Position: Front Passenger Side
- Part Name Code: 89542
- Item Weight: 0.90 Pounds
- Item Dimensions: 10.2 x 6.5 x 2.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 89542-48020
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2003 Toyota Highlander Submodels:
- Base, Hybrid, Hybrid Limited, Limited | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L FULL HYBRID EV-GAS (FHEV)

2003 Toyota Highlander Speed Sensor

Looking for affordable OEM 2003 Toyota Highlander Speed Sensor? Explore our comprehensive catalogue of genuine 2003 Toyota Highlander Speed Sensor. All our parts are covered by the manufacturer's warranty. Plus, our straightforward return policy and speedy delivery service ensure an unparalleled shopping experience. We look forward to your visit!

2003 Toyota Highlander Speed Sensor Parts Q&A

Q: How to replace a Speed Sensor on 2003 Toyota Highlander?
A: The replacement process for the skid control sensor begins by removing the rear wheel and disconnecting the connector from its sensor. The skid control sensor replacement process starts by taking off the LH rear disc brake caliper assembly followed by the removal of the rear disc. Secure the 4 bolts from the rear axle hub & bearing assembly RH to remove it. Mount the rear axle hub inside a soft jaw vise while the assembly needs replacement if the hub experiences sudden strong impacts or drops. Use a pin punch and hammer together with Special Service Tool to drive out pins from both attachments which will allow the removal of the tools from their special attachment point. Movement of the skid control sensor from the rear axle hub requires Special Service Tool: 09520-00031 (09520-00040), 09521-00020, 09950-00020 and 2 bolts (Diameter: 12 mm, pitch: 1.5 mm) by following precise steps to protect the sensor rotor while preventing surface damage of the axle hub and speed sensor. Clear both the new skid control sensor and the axle hub's contact surface from all foreign substance that could remain on the sensor rotor. A proper orientation of the skid control sensor connector should be maintained before pressing it onto the axle hub using Special Service Tool. Use the press tool to mount the sensor without hitting it directly with a hammer. Position the skid control sensor so it enters directly and proceed with slow insertion. Under post-installation procedures use 4 bolts to fasten the rear axle hub & bearing assembly RH while tightening them to 56 Nm (571 kgf-cm, 41 ft. lbs.). The installation sequence continues with the rear disc followed by the rear disc brake caliper assembly LH then the skid control sensor wire. Finish by installing the rear wheel and torquing it to 103 Nm then check the wheel alignment before verifying the ABS speed sensor signal.